================================================================================ ================================= Command to get and adjust Priamry CPICH Power (Default is 320) ================================================================================ ================================= RNRST08> get U08-BKK1536-1A pri.* RNRST08> set U08-BKK1536-1A primaryCpichPower 300 ================================================================================ ================================= Command to get and adjust Individualoffset (reccommeded is 0) ================================================================================ ================================= RNRST08> get U08-BKK2874-1A individualoffset.* RNRST08> set U08-BKK2874-1A individualOffset 30 RNRST08> set U08-BKK2874-1A individualOffset -30 ================================================================================ ================================= Command to get and set e-tilt ================================================================================ ================================= BKK1132-U08> get ret elect Result will be shown as below ================================================================================ ================================= MO Attribute Value ================================================================================ ================================= SectorAntenna=3,AuxPlugInUnit=2,RetuDeviceGroup=1,RetDeviceSet=1,RetDevice=1 ele ctricalAntennaTilt 60 SectorAntenna=1,AuxPlugInUnit=2,RetuDeviceGroup=1,RetDeviceSet=1,RetDevice=1 ele ctricalAntennaTilt 40 SectorAntenna=2,AuxPlugInUnit=2,RetuDeviceGroup=1,RetDeviceSet=1,RetDevice=1 ele ctricalAntennaTilt 40 ================================================================================ ================================= BKK1132-U08> set SectorAntenna=1,AuxPlugInUnit=2,RetuDeviceGroup=1,RetDeviceSet= 1,RetDevice=1 electricalAntennaTilt 60 ================================================================================ ================================= Command to get alarm ================================================================================ ================================= mobatch t 500 p 50 RBS.txt lt all;alt;lga --when u run mobatch it will read from your txt file if you put -p 50 it mean it will open every 50 sites in your list until finish it means it will run every 50 sites at same time -t is the expired time
after this amount of time (count by second) if there's no response it will close anyway, not so important I always put -t quite high but -p will effect, for node B & simple command you put p high is ok but if run mobatch for RNC & the data u wanna get is huge better reduce -p so the server wont be overload To learn the command you can start with type "h" ----================================================================================ ================================= Command to get & Set Primary CPICH power ================================================================================ ================================= RNRST08> get u08-bkk2874.* primarycpich.* ================================================================================ ================================= MO Attribute Value ================================================================================ ================================= UtranCell=U08-BKK2874-2A primaryCpichPower 320 UtranCell=U08-BKK2874-2B primaryCpichPower 320 UtranCell=U08-BKK2874-2C primaryCpichPower 320 UtranCell=U08-BKK2874-1A primaryCpichPower 320 UtranCell=U08-BKK2874-1B primaryCpichPower 320 UtranCell=U08-BKK2874-1C primaryCpichPower 320 ================================================================================ ================================= RNRST08> set u08-bkk2874-2B primarycpichpower 300 ================================================================================ ================================= Command to check whether cell is carring traffic. ================================================================================ ================================= BKK1352-U08> get radio Result ================================================================================ ================================= 1422 NodeBFunction=1,Sector=4,Carrier=1,RadioLin ks=1 ================================================================================ ================================= RadioLinksId 1 noOfRadioLinks 20 ================================================================================ ================================= ++++++ Command to check status of cell and channel ++++++++ ================================================================================ ================================= RNRST06> lst u08-bkk1664.* ( this will show adm and op state includding channel status including EUL channel.)
RNRST06> st u08-bkk1664.* ( this will show only adm and op state ) ================================================================================ ================================= ++++++ Command to check & Set admission control ++++++++ ================================================================================ ================================= RNSNK11> get BKK1132 sf8adm 130222-10:39:44 10.229.70.14 8.0v RNC_NODE_MODEL_M_1_200 stopfile=/tmp/16576 ================================================================================ ================================= MO Attribute Value ================================================================================ ================================= UtranCell=U08-BKK1132-1A sf8Adm 8 UtranCell=U08-BKK1132-1A sf8AdmUl 8 UtranCell=U08-BKK1132-1B sf8Adm 0 UtranCell=U08-BKK1132-1B sf8AdmUl 8 UtranCell=U08-BKK1132-2B sf8Adm 0 UtranCell=U08-BKK1132-2B sf8AdmUl 8 UtranCell=U08-BKK1132-2C sf8Adm 0 UtranCell=U08-BKK1132-2C sf8AdmUl 4 UtranCell=U08-BKK1132-1C sf8Adm 0 UtranCell=U08-BKK1132-1C sf8AdmUl 4 UtranCell=U08-BKK1132-2A sf8Adm 8 UtranCell=U08-BKK1132-2A sf8AdmUl 8 ================================================================================ ================================= RNSNK11> set UtranCell=U08-BKK1132-1B sf8Adm 8 130222-10:40:24 10.229.70.14 8.0v RNC_NODE_MODEL_M_1_200 stopfile=/tmp/16576 Set sf8Adm on following 1 MOs ? ================================================================================ === 17297 RncFunction=1,UtranCell=U08-BKK1132-1B ================================================================================ === Set sf8Adm on 1 MOs. Are you Sure [y/n] ? y ================================================================================ ============================ Id MO sf8Adm Result ================================================================================ ============================ 17297 UtranCell=U08-BKK1132-1B 8 >>> Set. ================================================================================ ================================= ++++++ Command to adjut out sync parameter ++++++++ ================================================================================ ================================= RNRST01> get u08-BKK2942.* noutsyncind
130226-18:12:59 10.229.66.4 8.0v RNC_NODE_MODEL_M_1_200 stopfile=/tmp/18678 ================================================================================ ================================= MO Attribute Value ================================================================================ ================================= UtranCell=U08-BKK2942-1B nOutSyncInd 20 UtranCell=U08-BKK2942-1C nOutSyncInd 10 UtranCell=U08-BKK2942-2A nOutSyncInd 20 UtranCell=U08-BKK2942-2B nOutSyncInd 20 UtranCell=U08-BKK2942-2C nOutSyncInd 10 UtranCell=U08-BKK2942-1A nOutSyncInd 20 ================================================================================ ================================= minPwrMax 0->10 minPwrRl -150 to -120 RNRST08 RNRST08> get u08-bkk2874.* minpwrmax 130313-11:15:57 10.229.66.11 8.0v RNC_NODE_MODEL_M_1_200 stopfile=/tmp/9950 ================================================================================ ================================= MO Attribute Value ================================================================================ ================================= UtranCell=U08-BKK2874-2A minPwrMax 0 UtranCell=U08-BKK2874-2B minPwrMax 20 UtranCell=U08-BKK2874-2C minPwrMax 20 UtranCell=U08-BKK2874-1A minPwrMax 0 UtranCell=U08-BKK2874-1B minPwrMax 20 UtranCell=U08-BKK2874-1C minPwrMax 20 ================================================================================ ================================= Total: 6 MOs RNRST08> get u08-bkk2874.* minpwrrl 130313-11:16:10 10.229.66.11 8.0v RNC_NODE_MODEL_M_1_200 stopfile=/tmp/9950 ================================================================================ ================================= MO Attribute Value ================================================================================ ================================= UtranCell=U08-BKK2874-2A minPwrRl -150 UtranCell=U08-BKK2874-2A minPwrRlTdd -24 UtranCell=U08-BKK2874-2B minPwrRl -150 UtranCell=U08-BKK2874-2B minPwrRlTdd -24 UtranCell=U08-BKK2874-2C minPwrRl -150 UtranCell=U08-BKK2874-2C minPwrRlTdd -24 UtranCell=U08-BKK2874-1A minPwrRl -150 UtranCell=U08-BKK2874-1A minPwrRlTdd -24 UtranCell=U08-BKK2874-1B minPwrRl -150 UtranCell=U08-BKK2874-1B minPwrRlTdd -24 UtranCell=U08-BKK2874-1C minPwrRl -150 UtranCell=U08-BKK2874-1C minPwrRlTdd -24 ================================================================================ ================================= Total: 6 MOs
RNRST08> pmx u08-bkk2874-1B -m 23 -h rabreleasespeech ================================================================================ ================================= ++++++ Command to check VSWR ++++++++ ================================================================================ ================================= BKK2874-U08> lh ru fui get vswr 130325-14:11:04 10.232.12.8 8.0v RBS_NODE_MODEL_N_1_50 stopfile=/tmp/82 ================================================================================ ============= $ lhsh 000100/port_0_dev_6 fui get vswr 0001p0d6: vswr: 25.3[dB] ================================================================================ ============= $ lhsh 000100/port_1_dev_7 fui get vswr 0001p1d7: vswr: 20.4[dB] ================================================================================ ============= $ lhsh 000100/port_2_dev_8 fui get vswr 0001p2d8: vswr: 23.8[dB]
RNRST08> h cedr ******************************************************************************** ******* ced[h][r][p] [-m |-c |-r ] [ | ] ******************************************************************************** ******* Print consumption of cell resources and rbs hw (RNC only). The following COLI commands are run on the module MPs in RNC: - celldata (ced/cedr) --> shows dynamic utrancell data, consumption of air inte rface resources - hwm (cedh/cedhp/cedhr) --> shows rbs Channel Elements consumption and number of RadioLinks/UEs Switches: - "r": re-read the data, otherwise, - "p": prints the CE consumption in nd). - "h": when the "h" switch is used, on Iub level, when the "h" switch is .
cached data is re-parsed. percentage (only applicable to "cedh" comma the resources consumption values are shown not used, they are shown on UtranCell level
Options: -m : only fetch/parse the data for certain RncModules, e.g. "-m 8" o r "-m 1,2,3" -c : only fetch/parse the data for specific UtranCells, e.g. "-c cel l304A" (not case sensitive) -r : only fetch/parse the data for specific IubLinks, eg. "-r iub_30 4" (not case sensitive) The output can be filtered by piping through some unix commands, eg. grep or sor
t. Examples: >> ced | grep 0019sp0 >> ced | sort -k 5 >> cedh -m 8,9,10 >> ced -r iub_304 ub_304 >> cedh -c cell304a ell304A
--> --> --> -->
print print print print
all cells configured on CC device 001900/sp0 cell data sorted on the fifth field CE usage for all sites in modules 8, 9, 10. cell data for all cells belonging to IubLink=I
--> print CE usage for the site connected to UtranCell=c
Printout format: > ced --------------------------------------------------------------------------------------------------------------------------------------------MOD CELL cid fro ro PwrDl/Adm dlCode ulInt sf8d sf8u sf16d sf16u sf32d sf4u dlASE ulASE HScnt EULs EULns CPMcnt CC_SP --------------------------------------------------------------------------------------------------------------------------------------------1 Iub-1-1 1031 0 0 7.0% 75% 6.2% -111.8 0/8 0/8 0/16 0/16 0/32 0/4 0/500 0/500 0/10 1/32 0/100 0/15 1:0019sp1 1 Iub-1-2 1032 1 2 7.0% 75% 6.2% -111.8 0/8 0/8 0/16 0/16 0/32 0/4 0/500 0/500 0/10 4/32 0/100 0/15 1:0021sp1 1 Iub-1-3 1033 2 3 7.0% 75% 22.9% -111.8 1/8 0/8 0/16 1/16 0/32 0/4 39/500 8/500 0/10 3/32 0/100 0/15 1:0019sp1 1 Iub-2-1 1037 6 1 7.0% 75% 24.6% -111.8 1/8 0/8 0/16 2/16 1/32 0/4 53/500 20/500 0/10 0/32 0/100 0/15 1:0019sp1 1 Iub-2-2 1038 7 4 7.0% 75% 10.8% -111.8 0/8 0/8 0/16 2/16 1/32 0/4 12/500 19/500 1/10 0/32 0/100 0/15 8:0023sp1(!) > cedh -----------------------------------------------------------------------------------------------------------------------------------------MOD GRP IUBLINK fro ro nCell usedCEdl usedCEul gHoCEdl gHoCEul OtherCEd l OtherCEul dlRL ulRL nrUE leakingCellFroIds -----------------------------------------------------------------------------------------------------------------------------------------1 0 b0157MDN 0 0 3 34/64 98/256 30/64 158/256 29/6 3 155/253 46 46 46 1 4 b0423MDN 5 2 2 2/64 6/128 62/64 122/128 61/6 3 120/126 3 3 3 1 8 b0407MDN 8 4 1 8/64 42/256 56/64 214/256 55/6 3 211/253 15 15 15 1 10 b0106MDN 9 5 3 40/96 125/256 56/96 131/256 55/9 5 128/253 48 48 49 147 > cedhp -----------------------------------------------------------------------------------------------------------------------------------------MOD GRP IUBLINK fro ro nCell usedCEdl usedCEul gHoCEdl gHoCEul OtherCEd l OtherCEul dlRL ulRL nrUE leakingCellFroIds -----------------------------------------------------------------------------------------------------------------------------------------1 0 b0157MDN 0 0 3 53.1% 38.3% 46.9% 61.7% 46.0 % 61.3% 46 46 46 1 4 b0423MDN 5 2 2 3.1% 4.7% 96.9% 95.3% 96.8 % 95.2% 3 3 3 1 8 b0407MDN 8 4 1 12.5% 16.4% 87.5% 83.6% 87.3 % 83.4% 15 15 15 1 10 b0106MDN 9 5 3 41.7% 48.8% 58.3% 51.2% 57.9
%
50.6%
48
48
49 147
The fields in the "ced" printout correspond to the following variables in the "c elldata" printout on Module MP: - MOD: RNC Module - cid: cId - fro: cellFroId (facade resource object, a unique id in the node) - ro: cell RO (resource object, a unique id in the module. Same as capsule inde x.) - PwrDl/PwrAdm: Filtered DL Power / pwrAdm - dlCode: DL Code Allocation Level - ulInt: UL Interference - sf8dl: SF8 RL DL Count / sf8Adm - sf8ul: SF8 RL UL Count / sf8AdmUl - sf16dl: SF16 RL DL Count / sf16Adm - sf16ul: SF16 RL UL Count / sf16AdmUl - sf32dl: SF32 RL DL Count / sf32Adm - sf4ul: SF4 RL UL Count / sf4AdmUl - dlASE: Total ASE DL / aseDlAdm - ulASE: Total ASE UL / aseUlAdm - HScnt: HSDPA UE Count / hsdpaUsersAdm - EULs: EUL UE Count serving / eulServingCellUsersAdm - EULns: EUL UE Count non-serving / eulNonServingCellUsersAdm - EUL2ms: EUL2ms UE Count serving / eulServingCellUsersAdmTti2 - Spch: Speech Only UE Count - CPMcnt: CPM RL Count / compModeAdm - Crn: Crnti allocation count - Hrn: Hrnti allocation count - CC_SP: The RncModule and SPM of the CC device handling the Cell. If the RncM odule controlling the CC device is different from the one controlling the cell, an exclamation mark (!) is printed, since this indicates that some performance p roblems may occur. The fields in the "cedh" printout correspond to the following variables in the " hwm print grp" printout on Module MP: - MOD: RNC Module - GRP: Cell Group (one or two per IubLink) - IUBLINK: the MO id of the IubLink - fro: the froId of the IubLink (facade resource object id, a unique id in the node) - ro: the RO Id of the IubLink (resource object id, unique in the module. Same as capsule index). - nCell: the number of UtranCells in the Cell Group - usedCEdl/usedCEul: Consumed Credit / Capacity Credit . The number of used CE out of the total amount of available CE. The total amount of available CE is cal culated in each RBS, based on the HW capability and the licensed capacity. - gHoCEdl/gHoCEul: Guaranteed, HO (Channel Elements availability for Guaranteed , Handover traffic) - OthrCEdl/OthrCEul: Other (Channel Elements availability for Other traffic) - dlRL, ulRL: number of Radio Links used in the RBS. The two values (downlink a nd uplink) should always be equal. - nrUE: number of UEs in the RBS. This should be equal to the number of Radio L inks. - leakingCellFroIds: the froId of Cells where dlRL, ulRL, nrUE are not equal. T his indicates that some resource has not been released properly in the cell. To release the resources in a leaking Cell, the corresponding IubLink MO must be lo cked and unlocked.
RNRST08> get bkk2874 ^remotecp 130325-14:50:33 10.229.66.11 8.0v RNC_NODE_MODEL_M_1_200 stopfile=/tmp/15980 ================================================================================ ================================= MO Attribute Value ================================================================================ ================================= IubLink=Iub_BKK2874-U08 remoteCpIpAddress1 10.23 3.12.8 IubLink=Iub_BKK2874-U08 remoteCpIpAddress2 ================================================================================ ================================= Total: 1 MOs RNRST08> get bkk2874 iub 130325-14:50:41 10.229.66.11 8.0v RNC_NODE_MODEL_M_1_200 stopfile=/tmp/15980 ================================================================================ ================================= MO Attribute Value ================================================================================ ================================= UtranCell=U08-BKK2874-2A iubLinkRef IubLin k=Iub_BKK2874-U08 UtranCell=U08-BKK2874-2B iubLinkRef IubLin k=Iub_BKK2874-U08 UtranCell=U08-BKK2874-2C iubLinkRef IubLin k=Iub_BKK2874-U08 UtranCell=U08-BKK2874-1A iubLinkRef IubLin k=Iub_BKK2874-U08 UtranCell=U08-BKK2874-1B iubLinkRef IubLin k=Iub_BKK2874-U08 UtranCell=U08-BKK2874-1C iubLinkRef IubLin k=Iub_BKK2874-U08 IubLink=Iub_BKK2874-U08 IubLinkId Iub_BK K2874-U08 IubLink=Iub_BKK2874-U08 iubLoadDlThresholdSpeech Struct{5} >>> 1.amr5900 = 100 >>> 2.amr7950 = 100 >>> 3.amr12200 = 100 >>> 4.amrWb8850 = 100 >>> 5.amrWb12650 = 100 IubLink=Iub_BKK2874-U08 iubLoadUlThresholdSpeech Struct{5} >>> 1.amr5900 = 100 >>> 2.amr7950 = 100 >>> 3.amr12200 = 100 >>> 4.amrWb8850 = 100 >>> 5.amrWb12650 = 100 ================================================================================ ================================= Total: 7 MOs RNRST08> cedr -r Iub_BKK2874-U08 130325-14:51:02 10.229.66.11 8.0v RNC_NODE_MODEL_M_1_200 stopfile=/tmp/15980
Trying password from ipdatabase file: /opt/ericsson/amos/moshell/sitefiles/ipdat abase... Checking available boards on node... ................ ......................... Created following board-groups: all, allp, mp, bp, tu, coremp, ommp, scb, sxb, s cx, sccpmp, et, etmfg, etmfx, aal2ap, aal2ncc, aal2cpsrc, aal2rh, xp, ranapmp, r nsapmp, mod, modact, modsb, modpdr, mod, mod, cc, cc, cc, dc, dc, dc, pdr, p dr, pdr, alld, spb, spb, spb. >>> Type "bp" to view available board-groups and "bp " to view group cont ents. Created following MO-groups: cc[0-9]dev, dc[0-9]dev, pdr[0-9]dev. >>> Type "mp" to view available MO-groups and "pr " to view group content s. ................................................................................ ................................................................................ ...................................................................... ..put /var/opt/ericsson/amos/moshell_logfiles/OS2133/logs_moshell/tempfiles/2013 0325-144908_15931/lhCmd15980 /d/usr/lhCmd15980 ... OK .... -----------------------------------------------------------------------------------------------------------------------------------------MOD CELL cid fro ro PwrDl/Adm dlCode ulInt sf8d sf8u sf16d sf16u sf32d sf4u dlASE ulASE CPMcn HScnt EULs EULns Eul2 Spch CC_SP -----------------------------------------------------------------------------------------------------------------------------------------1081 U08-BKK2874-1A 6493 465 24 54.6% 75% 38.1% -96.3 0/8 0/8 0/16 2/50 0/32 1/4 19/500 70/500 4/15 22/64 19/32 5/100 4/4 1 13 22 1081:00 20sp0 1081 U08-BKK2874-1B 6501 466 25 31.2% 75% 21.0% -98.2 0/8 0/4 0/16 0/50 0/32 0/0 5.0/500 3.6/500 1/15 6/64 6/32 0/100 3/4 0 1 6 1081:00 20sp0 1081 U08-BKK2874-1C 6502 467 26 33.9% 85% 20.4% -96.2 0/8 0/8 0/16 0/50 0/32 0/4 5.2/500 3.0/500 2/15 3/64 3/32 0/100 1/4 1 5 3 1081:00 20sp0 1081 U08-BKK2874-2A 6503 468 27 45.8% 75% 29.5% -94.7 0/8 0/0 0/16 3/50 0/32 0/0 14/500 21/500 1/15 15/64 12/32 2/100 0/0 3 13 15 1081:00 20sp0 1081 U08-BKK2874-2B 6511 469 28 27.4% 75% 15.3% -101.2 0/8 0/8 0/16 0/50 0/32 0/4 1.2/500 1.8/500 0/15 3/64 3/32 1/100 1/4 0 1 3 1081:00 20sp0 1081 U08-BKK2874-2C 6512 470 29 31.4% 85% 17.0% -94.5 0/8 0/8 0/16 2/50 0/32 0/4 2.6/500 17/500 1/15 4/64 2/32 1/100 0/4 0 2 4 1081:00 20sp0 -----------------------------------------------------------------------------------------------------------------------------------------Total (6 cells): 0 0 0 7 0 1 47 116.4 9 53 45 9 9 5 35 53 ------------------------------------------------------------------------------------------------------------------------------------------
