General Information Cavity Number
Tells which cavity used during multicavity production.
Lifting Eye Traceability Traceability Markings
Front
Back
Plane of the Eye
Forging Code
Identifies equipment used during forging operation.
Size
Shank diameter in inches.
Application: (a) Loads should always be applied to lifting eyes in the plane of the eye, not at some angle to this plane.
Heat Code
(b) Shoulder lifting eyes must be properly seated (should bear firmly against the mating part) otherwise the working loads must be reduced substantially. A steel washer or spacer may be required for proper seating.
Refers to specific heat of steel used. Diamond “D” Logo
Manufacturing trademark of the Edward W. W. Daniel Company
Physical Testing: Each lot of standard lifting eyes is manufactured and tested according to ASTM A489-93 A489-93 and ANSI B18. 15.
BREAKING BREAKING STRENGTH: STRENGTH: The threaded shank is screwed into one jaw of a testing machine and a pin secured to the other jaw passed through the eye.
BEND BEND TEST: TEST: Unthreaded parts must be capable of being bent to pressure or blows through 45˚ without showing cracks or indications of failure.
TENSILE TENSILE TEST: TEST: Per ASTM A489.
PLAI PLAIN N & SHOU SHOULD LDER ER LIFT LIFTIN ING G EYES EYES Material Data: Grade Grade . . . . . . . . . . . . . . C1030 C1030 Heat Treat . . . . . . . . . . . Quench & Draw Draw
Mechanical Properties: Grain Size Size . . . . . . . . . . . 5 or Finer Tensile . . . . . . . . . . . . . . 65,000 psi min. min. Yield . . . . . . . . . . . . . . . . 30,000 psi min. min. Elongation Elongation . . . . . . . . . . . 30% min. Reduction Reduction of Area Area . . . . . 60% min. Diamond “D” Lifting Eyes are processed and tested to the above requirements. Tests are performed on randomly selected lifting eyes from a given heat lot.
LIMITED WARRANTY: See page 36 . CERTIFICATIONS: Request for certification(s) must be made at time of order entry and there will be a charge associated with the certification.
FORGING TOLERANCES: TOLERANCES: Tolerances on all forged products is
(c) No greater load should be allowed than that given under rated capacity in each of the tables of dimensional data. (d) To obtain greatest strength from a lifting eye, it must fit reasonably tight in the hole into which it is screwed to prevent unscrewing due to twist of cable. Tightness Tightness and seating must be checked after initial load. (e) Lifting eyes should never be painted or otherwise coated when used for lifting, as such coatings will very likely cover up flaws. (f) To attain the rated capacity listed for regular lifting eyes, full thread engagement allowing 1/2 turn for alignment to the plane of the eye is necessary necessar y.
¹₃₂˝.
Lifting Eye Capacities RATED CAPACITY DIAMETER IN. MM ¹⁄₄ ⁵⁄₁₆ ³⁄₈ ⁷⁄₁₆ ¹⁄₂ ⁹⁄₁₆ ⁵⁄₈ ³⁄₄ ⁷⁄₈
1 1-¹⁄₈ 1-¹⁄₄ 1-¹⁄₂ 1-³⁄₄ 2 2-¹⁄₂
(M6) (M7) (M8) (M10) (M12) (M14) (M16) (M18) (M20) (M24) (M27) (M30) (M36) (M45) (M52) (M65)
0˚
45˚
LBS.
KGS
LBS.
KGS
500 900 1,300 1,800 2,400 3,200 4,000 5,000 7,000 9,000 12,000 15,000 21,000 28,000 38,000 56,000
(210) (370) (500) (740) (1,030) (1,600) (1,810) (2,140) (2,860) (3,850) (5,200) (6,400) (8,970) (11,960) (16,230) (24,200)
125 225 325 450 600 800 1,000 1,250 1,750 2,250 3,000 3,750 5,250 7,000 9,500 14,000
(52) (92) (125) (185) (257) (400) (452) (535) (715) (962) (1,300) (1,600) (2,242) (2,990) (4,057) (6,000)
over 45˚ N O T R E C O M M E N D E D
(Metric in Parenthesis)
NOTE ON LIFTING EYE & NUT EYE BOLT RATED CAPACITIES All rated lifting capacities included in the product charts are based on full sized shank and eye eye unaltered, and unaltered threading.
Lifting Eye Capacities & Safety information Rated Capacity: The maximum recommended load that should
Yield Strength: The maximum stress that can be applied to a material
be exerted on the item at zero zero degree vertical pull. All rated load values are for pulls exerted in the plane of the eye.
without permanent deformation of the material.
handbook is: the stress Ultimate Strength: As defined in the machinist’s handbook
i
at which a material in tension, compression, or shear will rupture or fracture.
Safety Factor: An industry term denoting theoretical capability . Lifting eye rated capacity is figured with a 5 to 1 safety factor for a zero degree straight vertical pull
Dimensions in Inches • Weight in Pounds Please include stock number and size when ordering
Eye Bolts Machinery Style Plain Pattern • Forged/ASTM A489 • 1030 Carbon Steel • Self-Colored** D
C E
B
Stock No.
Zink Plated Stock No.
13611 13621 13631 13638 13641 13650 13661 13672 13682 13702 13712 13723 13753 13770 13780 13790
ZP13611 ZP13621 ZP13631 ZP13638 ZP13641 ZP13650 ZP13661 ZP13672 ZP13682 ZP13702 ZP13712 ZP13723 ZP13753 ZP13770 ZP13780 ZP13790
Thread Size UNC-2A A
Shank Length B
1/4-20 5/16-18 3/8-16 7/16-14 1/2-13 9/16-12 5/8-11 3/4-10 7/8-9 1-8 1-1/8-7 1-1/4-7 1-1/2-6 1-3/4-5 2-4¹⁄ ² 2-1/2-4
I.D. Eye C
O.D. Eye D
Overall Length E
1
³⁄₄
1³⁄₁₆
2⁷⁄₃₂
1¹⁄₈
⁷⁄₈
1⁷⁄₁₆
2¹⁹⁄₃₂
1¹⁄₄
1
1¹¹⁄₁₆
3
1³⁄₈
1³⁄₃₂
1¹³⁄₁₆
3⁷⁄₃₂
1¹⁄₂
1³⁄₁₆
2¹⁄₈
3²¹⁄₃₂
1³⁄₄
1³⁄₈
2⁹⁄₁₆
4³⁄₈
1³⁄₄
1³⁄₈
2⁹⁄₁₆
4³⁄₈
2
1¹⁄₂
2¹³⁄₁₆
4⁷⁄₈
2¹⁄₄
1¹¹⁄₁₆
3³⁄₁₆
5¹₂
2¹⁄₂
1¹³⁄₁₆
3⁹⁄₁₆
6¹⁄₈
2³⁄₄
2
4¹⁄₁₆
6⁷⁄₈
3
2³⁄₁₆
4⁷⁄₁₆
7¹⁄₂
3¹⁄₂
2¹⁄₂
5³⁄₁₆
8³⁄₄
3³⁄₄
2⁷⁄₈
6
9¹³⁄₁₆
4
3¹⁄₄
6⁷⁄₈
11
5
4
8¹⁄₂
13⁵⁄₈
Approx. Wt. Per 100 Pcs.
5.0 10.0 15.0 20.0 35.0 60.0 60.0 90.0 145.0 200.0 285.0 390.0 635.0 1050.0 1470.0 2900.0
Rated Capacity Blanks*
500 900 1,300 1,800 2,400 3,200 4,000 5,000 7,000 9,000 12,000 15,000 21,000 28,000 38,000 56,000
R13611 R13621 R13631 R13638 R13641 R13650 R13661 R13672 R13682 R13702 R13712 R13723 R13753 R13770 R13780 —
Part #13650 dimensions not in accordance with ANSI B18.15.
A
8 Thread Pitch Machinery Style Plain Pattern • Forged/ASTM A489 • 1030 Carbon Steel • Self-Colored**
Stock No.
Thread Size UNC-2A A
Shank Length B
I.D. Eye C
O.D. Eye D
Overall Length E
Approx. Wt. Per 100 Pcs.
Rated Capacity
813712 813723
1-1/8-8 1-1/4-8
2³⁄₄ 3
2 2³⁄₁₆
4¹⁄₁₆ 4⁷⁄₁₆
6⁷⁄₈ 7¹⁄₂
285.0 390.0
12,000 15,000
813753 813770 813780 813790
1-1/2-8 1-3/4-8 2-8 2-1/2-8
3¹⁄₂
2¹⁄₂
5³⁄₁₆
8³⁄₄
3³⁄₄
2⁷⁄₈
6
9¹³⁄₁₆
4
3¹⁄₄
6⁷⁄₈
11
5
4
8¹⁄₂
13⁵⁄₈
635.0 1050.0 1470.0 2900.0
21,000 28,000 38,000 56,000
I.D. Eye C
O.D. Eye D
*Blanks have no rated capacity.
Plain Pattern
High Strength Eye Bolts
Stock No.
Thread Size UNC-2A A
1¹⁄₄
1
1¹¹⁄₁₆
3
1¹⁄₂
1³⁄₁₆
2¹⁄₁₆
3²¹⁄₃₂
13661LT
3/8 1/2 5/8
1³⁄₄
1³⁄₈
2⁹⁄₁₆
4³⁄₈
13672LT 13682LT 13702LT
3/4 7/8 1
2
1¹⁄₂
2¹³⁄₁₆
4⁷⁄₈
2¹⁄₄
1¹¹⁄₁₆
3³⁄₁₆
5¹⁄₂
2¹⁄₂
1¹³⁄₁₆
3⁹⁄₁₆
• Forged •8620 Alloy Steel • Low Temperature 13631LT Application 13641LT
Machinery Style Stainless Steel • 304 Stainless Steel D
C
SS13611 SS13621 SS13631 SS13641 SS13661 SS13672 SS13702
1/4-20 5/16-18 3/8-16 1/2-13 5/8-11 3/4-10 1-8
Shank Length B
I.D. Eye C
O.D. Eye D
Overall Length E
1
³⁄₄
1³⁄₁₆
2³⁄₈
1¹⁄₈
⁷⁄₈
1⁷⁄₁₆
2¹³⁄₁₆
1¹⁄₄
1
1¹¹⁄₁₆
3
1¹⁄₂
1³⁄₁₆
2¹⁄₈
3²¹⁄₃₂
1³⁄₄
1³⁄₈
2⁹⁄₁₆
4³⁄₈
2
1¹⁄₂
2¹³⁄₁₆
4⁷⁄₈
2¹⁄₂
1¹³⁄₁₆
3⁹⁄₁₆
6¹⁄₈
Overall Length E
6¹⁄₈
Approx. Wt. Per 100 Pcs.
5.0 9.6 14.0 29.5 58.0 88.5 226.0
Approx. Wt. Per 100 Pcs.
Rated Capacity
16.0 34.8 67.0
1,480 2,700 4,300
100.0 163.0 222.0
6,400 8,800 11,600
Rated Capacity
460 780 1,160 2,150 3,440 5,140 9,370
Blanks*
SSR13611 SSR13621 SSR13631 SSR13641 SSR13661 SSR13672 SSR13702
*Blanks have no rated capacity.
E B A
1
Stock No.
Thread Size UNC-2A A
Shank Length B
Plain Pattern
WARNING RATED CAPACITY IS DRASTICALLY REDUCED WHEN LOADING AT ANY ANGLE. LOADING MUST NEVER BE MADE AT AN ANGLE GREATER THAN 45° FROM BOLT CENTERLINE. AT AN ANGLE OF 45°, RATED CAPACITY IS REDUCED TO 1/4 OF THE TABULATED VALUE. Reference Page i
Dimensions in Inches • Weight in Pounds Please include stock number and size when ordering
Eye Bolts Nut Eye Bolts
Stock No.
• Forged • 1030 Carbon Steel • Hot Galvanized** • Plain Pattern A D
C B
NUT EYE BOLT SPECIFICATIONS Length of thread approximately four times the diameter of shank.Shanks 10 inches or longer are threaded 4 inches. Intermediate and longer sizes also available. 1/4" size only, electro-galvanized after threading. All other sizes hot galvanized. Available mechanical galvanized upon request. All standard stock eye bolts have UNC-2A threads and are supplied with American Standard Galvanized Oversized Hex Nuts (unassembled).
WARNING RATED CAPACITY IS DRASTICALLY REDUCED WHEN LOADING AT ANY ANGLE. LOADING MUST NEVER BE MADE AT AN ANGLE GREATER THAN 45° FROM BOLT CENTERLINE. AT AN ANGLE OF 45°, RATED CAPACITY IS REDUCED TO 1/4 OF THE TABULATED VALUE. Reference Page i RATED CAPACITY REFERS TO EYE BOLT ONLY. IMPROPER TORQUING, INFERIOR QUALITY NUTS AND OTHER FACTORS CAN SUBSTANTIALLY REDUCE RATED CAPACITY.
12310 12312 12314 12315*** 12316 12319 12321 12323 12325 12326 12330 12331 12333 12334*** 12335*** 12336 12338 12339 12340 12341 12343 12345 12347 12348 12350 12351 12352 12354 12356*** 12357 12358*** 12360 12362 12364 12366*** 12367 12368*** 12369*** 12370 12371 12373 12374 12375 12380 12382 12384 12385 12386*** 12387 12390 12391*** 12393 12396 12405
Thread Dia. A
1/4-20 1/4-20 1/4-20 1/4-20 1/4-20 5/16 -18 5/16 -18 5/16 -18 5/16 -18 5/16 -18 3/8-16 3/8-16 3/8-16 3/8-16 3/8-16 3/8-16 3/8-16 3/8-16 1/2-13 1/2-13 1/2-13 1/2-13 1/2-13 1/2-13 5/8-11 5/8-11 5/8-11 5/8-11 5/8-11 5/8-11 5/8-11 3/4-10 3/4-10 3/4-10 3/4-10 3/4-10 3/4-10 3/4-10 7/8-9 7/8-9 7/8-9 7/8-9 7/8-9 1-8 1-8 1-8 1-8 1-8 1-8 1-1/4-7 1-1/4-7 1-1/4-7 1-1/2-6 2
Shank Length B
2 3 4 5 6 2¹⁄₄ 3 4 5 6 2¹⁄₂ 3 4 4¹⁄₂ 5 6 8 10 3¹⁄₄ 4 6 8 10 12 4 5 6 8 10 12 15 4 6 8 10 12 15 18 5 6 8 10 12 6 8 10 12 15 18 6 8 12 12 12
I.D. Eye C
O.D. Eye D
Approx. Wt. Per 100 Pcs.
¹⁄₂
1
¹⁄₂
¹⁄₂
1 1 1 1
⁵⁄₈
1¹⁄₄
⁵⁄₈
1¹⁄₄
⁵⁄₈
1¹⁄₄
⁵⁄₈
1¹⁄₄
6.0 7.0 8.0 11.0 13.0 11.0 13.0 15.0 17.0 20.0 17.0 21.0 24.0 25.0 27.0 30.0 36.0 40.0 40.0 41.0 42.0 55.0 67.0 75.0 82.0 91.0 98.0 120.0 134.0 153.0 178.0 118.0 138.0 168.0 192.0 216.0 254.0 304.0 203.0 214.0 235.0 268.0 302.0 280.0 335.0 365.0 430.0 470.0 550.0 500.0 580.0 715.0 1080.0 1500.0
¹⁄₂ ¹⁄₂
⁵⁄₈
1¹⁄₄
³⁄₄
1¹⁄₂
³⁄₄
1¹⁄₂
³⁄₄
1¹⁄₂
³⁄₄
1¹⁄₂
³⁄₄
1¹⁄₂
³⁄₄
1¹⁄₂
³⁄₄
1¹⁄₂
³⁄₄
1¹⁄₂
1 1 1 1 1 1
2
1¹⁄₄
2¹⁄₂ 2¹⁄₂ 2¹⁄₂ 2¹⁄₂ 2¹⁄₂ 2¹⁄₂ 2¹⁄₂ 3 3 3 3 3 3 3 3¹⁄₂ 3¹⁄₂ 3¹⁄₂ 3¹⁄₂ 3¹⁄₂ 4 4 4 4 4 4 4⁷₁₆ 4⁷₁₆ 4⁷₁₆ 4⁷₁₆ 6⁷⁄₈
1¹⁄₄ 1¹⁄₄ 1¹⁄₄ 1¹⁄₄ 1¹⁄₄ 1¹⁄₄ 1¹⁄₂ 1¹⁄₂ 1¹⁄₂ 1¹⁄₂ 1¹⁄₂ 1¹⁄₂ 1¹⁄₂ 1³⁄₄ 1³⁄₄ 1³⁄₄ 1³⁄₄ 1³⁄₄ 2 2 2 2 2 2 2³⁄₁₆ 2³⁄₁₆ 2³⁄₁₆ 2¹⁄₂ 3¹⁄₂
2 2 2 2 2
*Blanks have no rated capacity. **Self-colored and other finishes available. Call for quote. Special bolt/thread lengths available. Call for quote. ***These products will be discontinued when stock is depleted.
5
Rated Capacity
500 500 500 500 500 800 800 800 800 800 1,200 1,200 1,200 1,200 1,200 1,200 1,200 1,200 2,100 2,100 2,100 2,100 2,100 2,100 3,200 3,200 3,200 3,200 3,200 3,200 3,200 4,500 4,500 4,500 4,500 4,500 4,500 4,500 7,000 7,000 7,000 7,000 7,000 8,500 8,500 8,500 8,500 8,500 8,500 13,500 13,500 13,500 20,000 35,000
Blanks*
R12316
R12326
R12336 R12339
R12343 R12348
R12352 R12357
R12362 R12367 R12369 R12371 R12375 R12380 R12385 R12387 R12390*** R12393 R12396 R12396
DIN 580/582 Eye Bolts & Nuts & Pad “D” Eyes E D
Metric Eye Bolts Manufactured to European Standards • DIN 580 • 1015 Carbon Steel • Self-Colored • Forged
A
Stock No.
Size
58006 58008 58010 58012 58014 58016 58020 58024 58030 58036 58042
6MM 8MM 10MM 12MM 14MM 16MM 20MM 24MM 30MM 36MM 42MM
O. D. Eye A
I .D. Eye B
Wi dt h of Shoulder C
Sh ank Length D
27 36 45 54 63 63 72 90 108 126 144
15 20 25 30 35 35 40 50 60 70 80
15 20 25 30 35 35 40 50 65 75 85
13 13 17 20.5 27 27 30 36 45 54 63
Ove ral l Length E
C
B
App rox . Wt . Ra te d Per C Capacity in Lbs. in Kgs.
27 36 45 53 62 62 71 90 109 128 147
4.9 13.2 24.2 39.6 55 61.6 100 162.8 365.2 583 886.6
70 140 230 340 490 700 1200 1800 3600 5100 7000
All dimensions are in millimeters. *Zinc Plating Special Order NOTE: These products are manufactured to Edward W. Daniel Co. quality standards via global contracts. E
Metric Eye Nuts Manufactured to European Standards • DIN 582 • 1015 Carbon Steel • Self-Colored • Forged
A
C D
B
C
Stock No.
58208 58210 58212 58214 58216 58220 58224 58230***
Size
O.D. Eye A
I.D. Eye B
Thread Dia. C
Width of Shoulder D
8MM 10MM 12MM 14MM 16MM 20MM 24MM 30MM
36 45 54 54 63 72 90 108
20 25 30 36 35 40 50 60
8-1.25 10-1.5 12-1.75 14-2 16-2 20-2.5 24-3 30-3.5
20 25 30 36 35 40 50 65
Overall Length E
36 45 53 52 62 71 90 109
Approx. Wt. Per C in Kgs.
10.6 19.4 31.7 38 49.3 80 130.3 292.2
All dimensions are in millimeters. Rated capacities are same as above when properly installed. (See DIN 580) *Zinc Plating Special Order NOTE: These products are manufactured to Edward W. Daniel Co. quality standards via global contracts. ***These products will be discontinued when stock is depleted.
Pad "D" Eyes • Forged Carbon Steel • Self-Colored B
A
C
D
Stock No.
41500 41502 41503 41504 41506 41507
O.D. Eye B
Width of Shoulder C
Overall Length D
³⁄₄
1³⁄₁₆
¹⁷⁄₃₂
1³⁄₈
⁷⁄₈
1⁷⁄₁₆
¹⁹⁄₃₂
1¹¹⁄₁₆
I.D. Eye A
1
1¹¹⁄₁₆
²¹⁄₃₂
2
1³⁄₁₆
2¹⁄₈
²⁹⁄₃₂
2⁷⁄₁₆
1³⁄₈
2⁹⁄₁₆
1¹⁄₃₂
3
1¹⁄₂
2¹³⁄₁₆
1³⁄₁₆
3¹⁄₄
Not recommended for Lifting.
7
Dimensions in Inches • Weight in Pounds Please include stock number and size when ordering
Approx. Wt. Per 100 Pcs.
7.5 9.4 11.0 16.0 56.0 86.0
