Frontier Manager Printer Controller Ver.2.0 (FRONTIER 350/370 System Disk Ver.7.7) (FRONTIER 355/375 System Disk Ver.1.7) (FRONTIER 570 System Disk Ver.1.7)
First Edition PP3-A1060E
distributed by www.minilablaser.com
INTRODUCTION This manual outlines the maintenance and servicing procedures, electrical diagram and parts list for the Frontier Manager Printer Controller (referred to as FMPC) for Fujifilm Digital Minilab FRONTIER 350/370/355/375/570. This manual is a professional publication provided for qualified service personnel or other persons fully trained in equipment service procedures. All other personnel and operators are restricted from servicing the FMPC. When maintenance service is needed, be sure to contact qualified service personnel. Precautions Generally Applying to All Servicing Operations When servicing internal machine parts, make sure the power switch and the main power supply on the power distribution board are both set to the OFF position. If the main power is left ON, electricity will flow as far as the power switch and power supply section, and this can cause electric shocks and/or short-circuiting. If the power is left on, there is also the possibility for the machine to be accidentally activated causing damage to the machine and/or bodily injury.
The light source section and dryer will be hot to the touch. Wait 15 minutes after turning off the power before commencing with servicing procedures. IMPORTANT IMPORTANT describes improper handling procedures that may adversely affect performance or damage the equipment. NOTE: NOTE designates those items, provisions, and supplementary explanations for which it is important to maintain methodical concern and consideration relative to operational procedures. : describes additional or useful information. Service Manual Appropriations 1. All rights are reserved by the Fuji Photo Film Co., Ltd. (FUJIFILM). 2. Manual usage is restricted to FUJIFILM equipment-related technical and service personnel. 3. This manual contains exclusive information relating to FUJIFILM equipment and is therefore proprietary. Unauthorized disclosure is prohibited. 4.FUJIFILM’s prior consent is required in regard to the following. KManual copying in whole or in part. KDisclosure of manual contents to unauthorized personnel. KManual uses for purposes other than technical service.
Recommended PC, Monitor Switcher, and Extension Cable for Keyboard ....................... 1.1.1 Recommended PC ................................................................................................. 1.1.2 Recommended Monitor Switcher ........................................................................... 1.1.3 Extension Cable for Keyboard................................................................................ 1.1.4 SP-3000 Monitor's Power Cable ............................................................................ 1.1.5 Ethernet Cable ....................................................................................................... Checking the Kit Contents ................................................................................................. Required Tools and CDs ................................................................................................... Power Souce Specification ................................................................................................
10 10 10 10 10 10 11 13 13
Installation for FRONTIER 570 ....................................................................................... 14 2.1 2.2
Installation Procedure List ................................................................................................. PC Preparations ................................................................................................................
2.2.1 IEEE1394 Board Installation .................................................................................. 2.2.2 Bios Setup .............................................................................................................. 2.2.3 Windows XP Installation and Partitioning............................................................... 2.2.4 Setup of Remaining Space in Hard Disk ................................................................ 2.2.5 Installing Other Driver Software ............................................................................. 2.2.6 User Registration.................................................................................................... 2.2.7 Windows Settings................................................................................................... 2.2.8 NetBEUI Setup ....................................................................................................... IEEE1394 Driver Pre-installation ....................................................................................... Copying Print Size Table from SP to FD ........................................................................... Creating Backup FD for SP-3000 and LP5700 .................................................................. Changing Mode from SP-3000 to FMPC ........................................................................... Connecting FMPC, FRONTIER, LAN Cable and Monitor Switcher ................................... Turning on LP5700 ............................................................................................................ Turning on FMPC and Installing LP5700 Driver ................................................................ Installing SP-3000 Driver ................................................................................................... Disabling Network Connection on SP Side ....................................................................... Installing FMPC Software [D20] ........................................................................................ Copying SP-3000 Print Size Table to FMPC ..................................................................... Installing DI Print/Data Writing Software [C4/C5] Client in FMPC ..................................... Turning on Imaging Controller ........................................................................................... Input/Output Device Setup for FMPC ................................................................................ Timer Setup in FMPC ........................................................................................................ Installation Information Setup in FMPC ............................................................................. Paper Condition Setup ...................................................................................................... FMPC Output Device Setting in Imaging Controller .......................................................... Operational Check ............................................................................................................. Creating Backup FD for FMPC/SP-3000 ........................................................................... System Shutdown ..............................................................................................................
Installation Procedure List ................................................................................................. PC Preparations ................................................................................................................ Disabling of “Rack Auto Cleaning” ..................................................................................... Creating Backup FD for SP-3000 and LP1500/2000 ......................................................... Replacing the ROM for Printer .......................................................................................... Connecting FMPC, FRONTIER, LAN Cable and Monitor Switcher ................................... Turning on FMPC .............................................................................................................. Disabling Network Connection on SP Side ....................................................................... IEEE1394 Driver Installation in SP .................................................................................... [A1] Stand-alone Version-up and DI Print/Data Writing Software Installation in SP .......... IEEE1394 Driver Pre-installation ....................................................................................... Installing IEEE1394 Driver for SP in FMPC ....................................................................... Starting-up LP in ROM Mode and Checking ROM Version (2.0-0x-000) .......................... Installing IEEE1394 Driver for LP in FMPC ....................................................................... FMPC [D20] Installation (Reinstall) with Printer’s Backup FD ........................................... DI Print/Data Writing Software [C4/C5] Client Installation in FMPC .................................. Installation Information Setup for FMPC ............................................................................ Output Device Setup for SP and Restarting SP ................................................................ Copying Print Size Table to FD then Copying SP-3000 Print Size Table to FMPC .......... FMPC Output Device Setting in Imaging Controller .......................................................... Enabling of “Rack Auto Cleaning” ..................................................................................... Paper Condition Setup ...................................................................................................... Creating Backup FD for FMPC, SP-3000 and LP1500/2000 ............................................ Operational Check ............................................................................................................. System Shutdown ..............................................................................................................
Installation Procedure List ................................................................................................. PC Preparations ................................................................................................................ Disabling of “Rack Auto Cleaning” ..................................................................................... Creating Backup FD for SP1500/2000, LP1500/2000 ....................................................... Replacing the ROM for Printer .......................................................................................... Connecting FMPC, FRONTIER, LAN Cable and Monitor Switcher ................................... Turning on FMPC .............................................................................................................. Disabling Network Connection on SP Side ....................................................................... [A1] Stand-alone Upgrade in SP [Ver.1.5 -> Ver.1.7] and DI Print/Data Writing Software [C4/C5] Client Installation in SP ....................................... IEEE1394 Driver Pre-installation ....................................................................................... Installing IEEE1394 Driver for SP in FMPC ....................................................................... Starting-up LP in ROM Mode and Checking ROM Version (2.0-0x-000) .......................... Installing IEEE1394 Driver for LP in FMPC ....................................................................... FMPC [D20] Software Installation (Reinstall) with Printer's Backup FD ............................ DI Print/Data Writing Software [C4/C5] Client Installation in FMPC ..................................
76 78 78 79 80 81 85 86 87 89 90 90 91 92 95
distributed by www.minilablaser.com
4.16 4.17 4.18 4.19 4.20 4.21 4.22 4.23 4.24
5
Installation Information Setup for FMPC ............................................................................ 96 Output Device Setup for SP and Restarting SP ................................................................ 97 Copying Print Size Table to FD then Copying LP1500/2000 Print Size Table to FMPC ... 98 FMPC Output Device Setting in Imaging Controller .......................................................... 99 Enabling of “Rack Auto Cleaning” ..................................................................................... 99 Paper Condition Setup ...................................................................................................... 99 Creating Backup FD for FMPC, SP1500/2000 and LP1500/2000 ..................................... 100 Operational Check ............................................................................................................. 101 System Shutdown .............................................................................................................. 101
Maintenance Menu (FRONTIER 350/370/355/375) .................................................. 102 5.1 5.2
5.3
5.4
Operational Procedure ...................................................................................................... 102 System Operation Setup and Check (41) .......................................................................... 103 5.2.1 Production Information 1 (411)............................................................................... 103 5.2.2 Production Information 2 (412)............................................................................... 5.2.3 Accumulated Production Information (413) ............................................................ 5.2.4 Timer Setup (414) ................................................................................................. 5.2.5 Error Information Check (415)............................................................................... 5.2.6 Installation Information Confirmation (416) ............................................................ 5.2.7 Data Backup (417) ................................................................................................. 5.2.8 Clear Error Log (41E) ............................................................................................. 5.2.9 Installation Information Setup (41F) ....................................................................... 5.2.10 DI Manager Administrative Setting (41l)................................................................. Print Condition Setup and Check (42) ............................................................................... 5.3.1 Paper Condition Setup ........................................................................................... 5.3.2 Processing Solution Temperature Check............................................................... 5.3.3 Control Strip Processing......................................................................................... 5.3.4 Print Size Setup (424) ............................................................................................ 5.3.5 Paper Condition Method Setup (42J) ..................................................................... 5.3.6 Back Print Setup (42O) .......................................................................................... Printer Adjustment/Maintenance (45) ................................................................................ 5.4.1 Paper Magazine Registration (451)........................................................................ 5.4.2 Paper Feed Length Adjustment (452) .................................................................... 5.4.3 Test Pattern Printing (453) ..................................................................................... 5.4.4 G, B Laser (SHG) Optimal Temperature Setup (454) ............................................ 5.4.5 Paper Feed (455) ................................................................................................... 5.4.6 Printer Temperature Display (456) ......................................................................... 5.4.7 Printer Input Check (457) ....................................................................................... 5.4.8 Image Position Fine Adjustment (458) ................................................................... 5.4.9 Printer I/O Check (45A) .......................................................................................... 5.4.10 Printer Function Select (45B) ................................................................................. 5.4.11 Laser Exposure Check (45C) ................................................................................. 5.4.12 R Laser (R-LD) Data (45D) .................................................................................... 5.4.13 G Laser (G-SHG) Data (45E) ................................................................................. 5.4.14 B Laser (B-SHG) Data (45F) ..................................................................................
Measures against FMPC Failures ................................................................................. 212 8.1 8.2
9
199 200 200 201 201 201 202
Error Messages and Countermeasures ..................................................................... 203 7.1
8
6.5.10 PS Liquid Concentration Management (46G) ........................................................ Option Adjustment / Maintenance (7) ................................................................................ 6.6.1 COM Port Setting (47A) ......................................................................................... Special Operations (9) ....................................................................................................... 6.7.1 Paint (49A) ............................................................................................................. 6.7.2 Explorer (49B) ........................................................................................................ 6.7.3 Command (49C).....................................................................................................
To Return to Direct-connecting Type in FRONTIER 350/370 ........................................... 212 To Return to Direct-connecting Type in FRONTIER 355/375 ........................................... 215
Index ......................................................................................................................................... 218
distributed by www.minilablaser.com
■ How to Read This Manual (1) Chapter Contents This manual consists of the following chapters. Chapter1 Preparations Describes the devices, tools and power source required for installation. Chapter2 Installation for FRONTIER 570 Describes the installing procedures for the FMPC for FRONTIER 570. Chapter3 Installation for FRONTIER 355/375 Describes the installing procedures for the FMPC for FRONTIER 355/375. Chapter4 Installation for FRONTIER 350/370 Describes the installing procedures for the FMPC for FRONTIER 350/370. Chapter5 Maintenance Menu (FRONTIER 350/370/355/375) Describes the maintenance menu (“Setup and Maintenance”) for the FMPC for FRONTIER 350/ 370/355/375. Chapter6 Maintenance Menu (FRONTIER570) Describes the maintenance menu (“Setup and Maintenance”) for the FMPC for FRONTIER 570. Chapter7 Error Messages and Countermeasures Lists up the FMPC error messages and their countermeasures. Chapter8 Measures against FMPC failures Describes how to connect SP to LP directly when the FMPC malfunctions. Chapter9 Index (2) Abbreviation for Devices The abbreviation of devices at the upper right-hand of the page (in the Chapter Title bar) shows where the current installing operation is done. The following abbreviations are used. • Frontier Manager Printer Controller: • Imaging Controller: • FRONTIER Scanner: • FRONTIER Printer: • FRONTIER 350/370: • FRONTIER 355/375: • FRONTIER 570: • FRONTIER 350/370/355/375/570:
Abbriviation
FMPC IC SP LP F350/370 F355/375 F570 F350/370/355/375/570
(3) Notation for Screen/Button Name • Screen name is enclosed within “ ”. • Button name is enclosed within [ ] parentheses. • Items on the screen is enclosed within [ ] parentheses.
9
distributed by www.minilablaser.com
1
Preparations Recommended PC, Monitor Switcher, and Extension Cable for Keyboard
1.1
1.1.1 Recommended PC • • • •
Model Main Body CPU Chip Set
: : : :
• • • • •
Memory HDD Network I/O Devices OS
: : : : :
Dell Optiplex GX280 (No monitor) Small Mini Tower Pentium-4 2.8GHz/800FSB (FSB800MHz) IntelR 915G Express IntelR Hyper-Threading Function disabled 1GB/DDR2 SDRAM 400MHz Serial ATA 80GB/7200rpm IntelR Pro/1000MT(10/100/1000) for interface 3.5˝ FDD, CD-ROM, Built-in Audio-speaker WindowsR XP Professional SP1/SP2
• PCI Bus : More than 3 (for IEEE1394 x 2 and 2nd Serial Adapter Card) • Dimension : (Width x Height x Depth) : 181 x 447 x 426 mm : IMPORTANT • To supply the power source to the FMP, make sure to use the power source cable, sharing the grounding with the printer as much as possible, so that the voltage deviation between the FMPC and printer does not occur. • Install the FMPC so shat their cables are not tightened. For example, if the 1394 board is loosened by pulling the cable, the communication error may occur.
1.1.2 Recommended Monitor Switcher • • • • • • •
CPU Auto-Switcher PC: IBM PC/AT Keyboard : PS/2 Keyboard Mouse : PS/2 Mouse Monitor : HD(3WAY)/Multi-scan display with 15pin connector OS : WindowsR XP, WindowsR 2000, WindowsR NT Method : Electric Control by pressing the select switches or pressing [Ctrl] key twice quickly (hot-key switching)/ Auto-scanning
1.1.3 Extension Cable for Keyboard • Extension cable for keyboard : KB-KYE2 (2m) • Supported keyboard : General keyboard (Mini-DIN 6pin-type)
1.1.4 SP-3000 Monitor's Power Cable 1.1.5 Ethernet Cable
10
distributed by www.minilablaser.com
1.2
Checking the Kit Contents
Check the kit contents. [FMPC Kit]
1
Part Name
Part No.
FMP Controller Kit
899C21583A2
Shape and Identification
F350/370 System Software [A1] Ver.7.7-0E-201
FMP Controller [D20] CD Ver.2.0-0E-101
F355/375/570 System Software [A1] CD Ver.1.7-0E-105
F355/375/570 Driver Disk
FMP Controller Driver Disk
Custom Button Setting Tools CD
Blank FD for Backup (3)
Instruction Manual
2
FMPC Software
899C21583A4
ROM (for CTL CB)
IEEE1394 Board x 2
IEEE1394 Cable (4.5m) x 1
Installation/ Service Manual/ Parts List
Operator Quick Reference Guide
F350/370 System Software [A1] Ver.7.7-0E-201
FMP Controller [D20] CD Ver.2.0-0E-101
F355/375/570 System Software [A1] CD Ver.1.7-0E-105
F355/375/570 Driver Disk
FMP Controller Driver Disk
Custom Button Setting Tools CD
11
distributed by www.minilablaser.com
[Each Part] Part Name
Part No.
1
IEEE 1394 Board
113C898440
2
ROM(for CTL CB)
114C898435
3
IEEE 1394 Cable (4.5m)
136C898441
4
FMP Controller [D20] CD Ver.2.0-0E-101
114C6006886E00
5
F355/375/570 System Software [A1] CD Ver.1.7-0E-105
114C2159701E03
6
FRONTIER 350/ 370 System Software [A1] CD Ver.7.7-E
114C6006883E01
7
F350/370 System Software [A1] CD Ver.7.7-0E-201 —
8
Installation/Service Manual/Parts List
—
12
Shape and Identification
distributed by www.minilablaser.com
Part Name 9
Part No.
Shape and Identification
Operator Quick Reference Guide
—
10
Custom Button Setting Tools CD
114C2159702E00
11
1394 Driver Disk for SP-3000
114C2159703X00
12
1394 Driver Disk for FMPC
114C6006884X00
13
Blank FD for Backup CD
114C1062675(FMPC) 114C1062676(SP) 114C1058873(LP)
1.3 • • • • • •
Required Tools and CDs
ROM remover or screw driver (-) Windows XP Professional SP1/SP2 CD DI Print/Data Writing Service Software [C4/C5] CD Insulating tape Print Size Set Tool Software (FD) “3KPrintsizeCopyTool” Software (FD) (used only in case of FRONTIER 355/375)
1.4
Power Souce Specification
Make sure that the AC power at the installation location is correct by checking the rated label of the PC.
13
distributed by www.minilablaser.com
2
Installation for FRONTIER 570
FMPC
Install the FMPC devices and software, and set them up for use.
2.1
Installation Procedure List
Install the FMPC using the following procedure. No.
Procedures FMPC
Refer to
1
IEEE1394 Board Installation
2
PC Preparations
FMPC
See Section 2.2 on page 15
3
IEEE1394 Driver Pre-installation
FMPC
See Section 2.3 on page 29
4
Copying Print Size Table from SP to FD
SP
See Section 2.4 on page 30
5
Creating Backup FD for SP-3000 and LP5700
SP
See Section 2.5 on page 30
6
Changing Mode from SP-3000 to FMPC
SP
See Section 2.6 on page 31
7
Connecting FMPC, FRONTIER, LAN cable and Monitor Switcher
SP, FMPC, LP, Monitor Switcher
See Section 2.7 on page 31
8
Turning on LP5700
LP
See Section 2.8 on page 35
9
Turning on FMPC and Installing LP5700 Driver
FMPC
See Section 2.9 on page 36
10
Installing SP-3000 Driver
FMPC
See Section 2.10 on page 37
11
Disabling Network Connection on SP Side
FMPC
See Section 2.11 on page 38
12
Installing FMPC Software [D20]
FMPC
See Section 2.12 on page 39
13
Copying SP-3000 Print Size Table to FMPC
FMPC
See Section 2.13 on page 40
14
Installing DI Print/Data Writing Software [C4/C5] Client in FMPC
2.2.1 IEEE1394 Board Installation Install the two 1394 boards in the FMPC.
1
Remove the second and third dummy covers from the left in the board section. Dummy Covers (2)
While pressing the two buttons on each side, open the upper cover slowly. Upper Cover
NMP003
4
Insert the 1394 board into the slot that is the third from the left, then pressing it on slowly, and then confirm that it is securely installed in the slot. 1394 Board
Buttons (2) NMP001
2
Lift up the board stopper while pressing the hook. Board Stopper
NMP004
5
In the same way, install another 1394 board in the slot that is the second from the left. 1394 Board
Hook NMP002
NMP005
15
distributed by www.minilablaser.com
FMPC
6
Lower the stopper until the click sounds to secure the boards.
2.2.2 Bios Setup Start up the FMPC, then press the [F2] key just when “Strike F1 to retry boot, F2 for setup utility”. Make sure that “Hyper - threading” is set to “Disabled”.
Board Stopper
If [Hyper-Threading] is changed to “Enabled”, the Windows must be installed again.
NMP006
7
2.2.3 Windows XP Installation and Partitioning Install the Windows XP Professional in the FMPC PC, then set up the partition.
Close the upper cover. Upper Cover
It is not necessary to install it when using a PC with Windows XP Professional already installed.
[Procedures]
1
Insert the Windows XP Professional installer CD into the CD drive.
NMP007
NMP012
16
distributed by www.minilablaser.com
FMPC
2
6
Set up the PC again.
7
When the message “The partition you tried to delete is a system partition” appears, press the [Enter] key, then the [L] key. After all partitions are deleted, select [Unpartitioned space], then press the [C] key. Windows XP Professional Setup The following list shows the existing partitions and unpartitioned space on this computer. Use the UP and DOWN ARROW keys to select an item in the list. • To set up Windows XP on the selected item, press ENTER. • To create a partition in the unpartitioned space, press C. • To delete the selected partition, press D. 76294 MB Disk 0 at Id 0 on bus 0 on atapi [MBR]
NMP010
3
When the message “Press any key to boot from CD” appears, press the [Enter] key.
Unpartitioned space
8
Press any key to boot from CD.
76293 MB
Set “10000MB” for the partition size, and press the [Enter] key. Windows XP Professional Setup You asked Setup to create a new partition on 76294 MB Disk 0 at Id 0 on bus 0 on atapi [MBR]. • To create the new partition, enter a size below and press ENTER.
4
• To go back to the previous screen without creating the partition, press ESC.
When the message “Windows XP Licensing Agreement” appears, press the [F8] key if you agree to the terms of the license.
The minimum size for the new partition is 8 megabytes (MB). The maximum size for the new partition is 76285 megabytes (MB). Create partition of size (in MB): 100000
9
Windows XP Licensing Agreement Microsoft Windows XP Professional. Microsoft (r) Windows (r) XP Tablet PC Edition and Microsoft (r) Windows (r) XP Media Center Editon END-USER LICENSE AGREEMENT IMPORTANT-READ CAREFULLY : This End-User License Agreement (“EULA”) is a legal agreement between you (either an individual or a single legal entity) and the manufacturer (“Manufacturer”) of the computer system or computer system component (“HARDWARE”) with which you acquired the Microsoft software product (s) identified on the Certificate of Authenticity (“COA”) affixed to the HARDWARE or on the associated product documentation (“SOFTWARE”). The SOFTWARE includes Microsoft computer software, and may include associated media, printed materials, “online” or electronic documentation, and Internet based services. Note, however, that any software, documentation, or web services that are included in the SOFTWARE, or accessible via the SOFTWARE, and are accompanied by their own license agreements or terms of use are governed by such agreements rather than this EULA. The terms of printed paper EULA, which may accompany the
5
Select the above “10000MB” partition, and press the [Enter] key. Windows XP Professional Setup The following list shows the existing partitions and unpartitioned space on this computer. Use the UP and DOWN ARROW keys to select an item in the list. • To set up Windows XP on the selected item, press ENTER. • To create a partition in the unpartitioned space, press C. • To delete the selected partition, press D. 76294 MB Disk 0 at Id 0 on bus 0 on atapi [MBR] C: Partition1 [New (Raw)] Unpartitioned space
When the message “The following list shows the existing partitions and unpartitioned space on this computer” appears, press the [D] key to delete all existing partition(s).
10
1001 MB (10001 MB free) 66292 MB
Format this partition with NTFS. Windows XP Professional Setup
Windows XP Professional Setup
The partition you selected is not formatted. Setup will now format the partition.
The following list shows the existing partitions and unpartitioned space on this computer. Use the UP and DOWN ARROW key to select an item in the list. • To set up Windows XP on the selected item, press ENTER. • To create a partition in the unpartitioned space, press C. • To delete the selected partition, press D.
Use the UP and DOWN ARROW key to select the file system you want, and then press ENTER. If you want to select a different partition for Windows XP, press ESC. Format Format Format Format
the the the the
partition partition partition partition
using using using using
the the the the
NIFS file system (quick) FAT file system (quick) NIFS file system FAT file system
76294 MB Disk 0 at Id 0 on bus 0 on atapi [MBR] C: Partition 1 [New (Raw)] Unpartitioned space
10001 MB ( 10001 MB free) 66292 MB
17
distributed by www.minilablaser.com
FMPC
11
After the format is completed, the PC is automatically restarted. Windows XP Professional Setup
2.2.4 Setup of Remaining Space in Hard Disk Set up the remaining space in the hard disk.
This portion of Setup has completed successfully. If there is a floppy disk in drive A:, remove it. To restart your computer, press ENTER. When your computer restarts. Setup will continue.
1
On the Desktop, select [Start] - [Control Panel] [Administrative Tool] - [Computer Management] to display the “Computer Management” screen.
Your computer will reboot in 2 secons....
12 13
14 15
After the restart, DO NOT press any key until the wizard screen appears even if “Press any key to boot from CD” is displayed. While following the Wizard instructions, complete [Regional and Language Options], [Personalize Your Software], [Computer Name and Administrator Password] and [Date and Settings]. After the system is restarted, Windows XP Desktop screen appears.
2
Restart the PC, and change the drive reading order at the start-up to [1. Diskette Drive] [2. Hard-disk Drive C:] - [3. IDE CD-ROM Device] (For procedures, See “2.2.2 Bios Setup” on page 16.).
3
18
Right-click on the unallocated area, then select [New Partition].
On the “Welcome to New...” screen, click the [Next] button.
distributed by www.minilablaser.com
FMPC
4
On the “New Partition Wizard” screen, select [Extended partition], then click the [Next] button.
5
Click the [Next] button.
6
Click the [Finish] button.
7
8
9
In the same area on the “Computer Management” screen, right-click, then select [New Logical Drive].
On the “Welcome to New...” screen, click the [Next] button.
On the “Select Partition Type” screen, select [Logical drive], then click the [Next] button.
19
distributed by www.minilablaser.com
FMPC
10
11
12
20
Click the [Next] button.
Specify “D” for [Assign the following...], then click the [Next] button.
Select [NTFS] for “File system”, then click the [Next] button.
13
14
15
Formatting is started.
After formatting is completed, check if “New Volume” is “Healthy”.
Right-click on the CD drive, then select [Change Drive Letter and Paths].
distributed by www.minilablaser.com
FMPC
16
Select “N”, and then click the [OK] button.
2.2.6 User Registration Register the following user name and password. USER NAME: FRONTIER PASSWORD: FRONTIER GROUP: Administrator
17
Click the [X] button to close the opened screens.
The following procedures are an example when using the Wizard.
1
On the Desktop, select [Start] - [Control Panel] [User Accounts], then on the “User Accounts” screen, click [Create a new account], then [Apply Options] button, then enter “FRONTIER” and then click the [Next] button.
2.2.5 Installing Other Driver Software Install other driver software provided in the DELL setup CD. (For details, see “Instruction Manual” for DELL PC.)
2
Select “Computer administrator”, then click the [Create Account] button.
21
distributed by www.minilablaser.com
FMPC
3
On the “User Accounts” screen, click [Change the way users log on or off], then enter “FRONTIER” both in the “Type a new password” and “Type a new password again...”, then click the [Create Password] button.
2.2.7 Windows Settings Set up the Windows functions. Log on with the user name “FRONTIER”, then start settings.
(1) Disabling of Windows XP Style
1
4
Open the “Control Panel” screen, then click [Switch to Classic View].
2
5
On the Desktop, select [Start] - [Run], then on the “Run” screen, enter “Services.msc”, then click the [OK] button.
Click the [User Account] button, then click [Change the way users log on or off], and then on the “Select logon and logoff options” screen, remove the checkmark [✓] from “Use the Welcome screen”, then click the [Apply options] button.
3
22
After the system is restarted, right-click on any part of the Desktop, then open the [Display Properties] screen, and then select [Windows Classic] for [Theme].
On the “Service” screen, double-click [Themes].
distributed by www.minilablaser.com
FMPC
4
On the “Themes Properties (Local Computer)” screen, select “Disabled” for [Startup type], then click the [Stop], then [OK] button.
(3) Long Date Format Setting
1
Double-click the [Regional and Language Options] on the “Control Panel” screen, then on the “Regional Options” tab screen, click the [Customize] button to set a long date format, then click the [Apply] - [OK] buttons.
(2) Password History Setting
1
On the Desktop, select [Start] - [Control Panel] [Administrative Tools] - [Local Security Policy] to open the “Local Security Settings” screen.
(4) System Error Setting
1
2
On the Desktop, select [Start] - [Control Panel] [System], then on the “System Properties” screen, click [Advanced] tab, then click the [Settings] button for [Startup and Recovery], then set up as shown below.
Select [Password Policy] - [Enforce password history], then in the “Enforce password history Properties” dialog, select “0” for [Password remembered], then click the [Apply], then [OK] button.
23
distributed by www.minilablaser.com
FMPC
[✔] : Write an event to the system log [✔] : Send an administrative alert [ ] : Automatically restart “Complete memory dump” for [Write debugging information] “D:\MEMORY.DMP” for [Dump file] [✔] : Overwrite any existing file
2
2
After the above items are set, click the [OK] button.
3
(5) Disabling of User Assistant Function
1
24
In the “Settings for StickyKeys” dialog, click the [Settings] for [FilterKeys], then remove all check marks [✓], then click the [OK] button.
On the Desktop, select [Start] - [Control Panel] [Accessibility Options], then in the “Settings for StickyKeys” dialog, click the [Settings] for [StickyKeys], then remove all checkmarks [✓], then click the [OK] button.
In the “Settings for StickyKeys” dialog, click the [Settings] for [ToggleKeys], then remove the checkmark [✓] in the “Use shortcut”, then click the [OK] button.
distributed by www.minilablaser.com
FMPC
4
Click the [OK] button to close the “Settings for StickyKeys” dialog.
2
Add the checkmark [✓] to “On-Screen Keyboard” dialog, then click the [OK] button.
(7) Disabling of Error Reporting
1
On the Desktop, select [Start] - [Control Panel] [System], then on the “System Properties” screen, click [Advanced] tab, then click the [Error Reporting] button.
(6) Non-display Setting of Screen Keyboard Dialog Box
1
On the Desktop, select [Start] - [All Programs] [Accessories] - [Accessibility] - [On-screen Keyboard].
25
distributed by www.minilablaser.com
FMPC
2
Select “Disable error reporting”, then remove the checkmark [✓] from “But notify me....”, then click the [OK] button.
(9) Screen Resolution
1
Right-click on any part of the Desktop, then on the “Settings” tab screen of the “Display Properties” screen, select more than “800 by 600 pixels” for “Screen area”, then more than 24 bit (True Color) for “Colors”, then click the [Apply] [OK] buttons.
(8) Non-display Setting for Taskbar
3
On the Desktop, select [Start] - [Control Panel] [Taskbar and Start Menu], add the checkmark [✓] to “Auto-hide the taskbar”, then click the [OK] button.
(10) Non-display Setting of Screen Saver
1
26
Right-click on any part of the Desktop, then on the “Screen Saver” tab screen of the “Display Properties” screen, set “None” for “Screen saver”, then click the [Apply] - [OK] buttons.
distributed by www.minilablaser.com
FMPC
(11) Disabling of Power Standby
1
Double-click the [Power Options] on the “Control Panel” screen, then on the “Power Options Properties” tab screen, select “Never” for “Turn off monitor”, “Turn off hard disks” and “System standby”, then click the [Apply] - [OK] buttons.
(12) Disabling of Auto Update
1
On the Desktop, select “Control Panel” “System” - “Automatic Updates”, then remove the checkmark [✓] from “Keep my computer up to date. ........”, then click the [Apply] - [OK] buttons.
(13) Disabling of Desktop Cleanup
1
Right-click on any part of the Desktop, then select “Desktop” tab - “Customize desktop”, then remove the checkmark [✓] from "Desktop cleanup", then click the [OK] button.
(14) “Visual Notification” to ON in Dr. Watson Dialog Box
1
On the Desktop, select [Start] - [Run], then enter “Drwtsn32” and then click the [OK] button. In the “Dr. Watson for Windows” dialog box, add the checkmark [✓] to “Visual Notification” in “Options”.
27
distributed by www.minilablaser.com
FMPC
(15) Non-display Setting of Internet Explorer Dialog Box
1
2.2.8 NetBEUI Setup Set up the NetBEUI protocol in the FMPC.
Select [Control Panel] - [Internet Options] [Security] tab, then click the [Custom Level...], then select [Miscellaneous] - [Submit nonencrypted form data], then select “Enable”.
[Required Files] To set up the NetBEUI, the following files stored in the Windows XP installer CD are required. CD Drive\Valueadd\Msft\Net\Netbeui They are to be copied in the following folders in the HD of the FMPC. File Name Target
Folder
1
Netnbf.inf
C:\windows\inf
2
nbf.sys
C:\windows\system32\drivers
NOTE: Make all files and their extensions visible by using [Tools]/[FolderOptions] before hand.
[Procedures] When using the Service Pack2 (SP2), also set up the following two items.
1
(16) Disabling the Windows Fire Wall
2
1 2 3
Open the [Control Panel]. Double-click the [Windows Fire Wall]. Select [Off], then click the [OK] button.
(17) Disabling the Security Center
1 2 3
28
On the Desktop screen, select [Start] -> [Run], then enter “service.msc”, and then click the [OK] button. Double-click the [Security Center] to open the properties screen, then select [Disabled] for [Startup type], and then click the [Stop] button. Click the [Apply], then [OK] button.
Right-click on the [My Network] icon to open the “My Network Properties” screen. Copy “Netnbf.inf” and “nbf.sys” in the CD to any folder in the hard disk.
3
Open the “Local Area Connection Properties”.
4
Click the [Install] button.
distributed by www.minilablaser.com
FMPC
5
Select [Protocol], then click the [Add] button.
6 7 8
2.3
1
Select [NetBEUI Protocol], then click the [OK] button. Make sure that the [NetBEUI Protocol] is added in the list. This completes the NetBEUI seup.
IEEE1394 Driver Pre-installation
Insert the FMPC driver CD into the CD-ROM, then in the “Device Drivers Disk [D-01]” dialog box, click the [OK] button. This completes the FMPC driver disk setup.
2
When the FMPC driver disk setup is completed normally, the “Device Drivers Disk [D-02]” dialog box appears. Remove the driver disk from the CD-ROM drive, then click the [OK] button to shut down the system. After shutdown, turn on the FMPC.
29
distributed by www.minilablaser.com
SP
2.4
Copying Print Size Table from SP to FD
Copy the print size table from SP to FD by using the dedicated print size copy tool.
1 2
Insert the print size copy tool FD into the FD drive of SP-3000, open the Explorer, then execute “PrintSizeTool.exe” in FD.
3
After copying, the following message appears.
When the FRONTIER model and System [A1] is proper, the following message appears. Click the [OK] button to start copying it to the system.
2.5
Creating Backup FD for SP-3000 and LP5700
Create a backup FD for SP-3000 and LP5700 in SP.
2 3
Insert the floppy disk into the floppy drive of the main control unit. Move the cursor to the “Destination” box and select “Film Scanner”, “Printer Processor” or “Pricing Unit”.
NOTE: Perform the data backup for the pricing unit when pricing unit data is changed. Data is backed up from the pricing unit to the hard disk of the main control unit. If the data backup is not performed, changed pricing unit data is canceled when starting up the system next time.
[Selection]
4
“4 Setup and Maintenance” - ”1 System Operation and Check” - ”7 Data Backup”
1
Prepare a new floppy disk for data backup when backing up data.
• The “Making the backup of the data” message appears.
5
NOTE: A floppy disk is unnecessary for pricing unit data backup because data is backed up to the hard disk of the main control unit.
30
Click the [OK] button.
Upon completion of the backup, click the [Cancel] button.
• Operation returns to the menu screen.
6
Remove the floppy disk from the drive.
distributed by www.minilablaser.com
SP
2.6
/
FMPC
SP
LP
Changing Mode from SP-3000 to FMPC
In SP, change the mode from SP-3000 to FMP Controller, then shut down the SP through the postoperational checks.
[Selection] “4 Setup and Maintenance” - ”1 System Operation Setup and Check” - ”F Installation Information Setup”
1 2
Change the output device from “LP-5700” to “FMP Controller”. Click the [OK] button.
• Operation returns to the menu screen.
3
Perform the post-operational checks to shut down the system and then restart the system.
• The new settings are activated.
2.7
Connecting FMPC, FRONTIER, LAN Cable and Monitor Switcher
Connect the SP-3000, FMPC, LP5700, LAN cable and the monitor switcher.
(1) IEEE1394 Cable Preparation
2 3
Remove the clamp from the cable. Bind the bared part of the cable with insulating tape. Clamp
Bind the bared part of the existing IEEE1394 cable connected between the printer (LP) and scanner (SP).
1
Disconnect the IEEE1394 cable from the scanner(SP). Insulating Tape IEEE1394 Cable MP006
MP047
31
distributed by www.minilablaser.com
SP
LP
FMPC
(2) IEEE1394 Cable Connection Preparations Connect the IEEE1394 cable from the LP to the connector in right-hand board, then connect the cable from the SP to the one in the left-hand board. IMPORTANT Do not connect the two cables to the same board in the FMPC.
Scanner (SP)
Printer (LP)
Existing IEEE1394 Cable (10m)
IEEE1394 Cable (4.5m)
IMPORTANT Make sure that the IEEE1394 cable from scanner (SP) is connected to the lower board, and the cable from printer (LP) to the upper board.
32
distributed by www.minilablaser.com
SP
LP
FMPC
(3) Monitor Switcher Connections Connect the FMPC, monitor switcher, and FRONTIER as follows. It is recommended that the monitor switcher be installed on the main control unit.
MP046
By placing the full keyboard as shown above, you can press the [Ctrl] key easily to switch the display.
33
distributed by www.minilablaser.com
SP
LP
FMPC
(4) Other Connections Connect the FMPC, FRONTIER and the monitor switcher and then connect the LAN cable from the HUB to which the Imaging Controller is connected as shown in the following connection diagram.
FRONTIER (SP) 4
5
3
1
2 IMPORTANT Connect the monitor’s power cable to the power supply directly. Do not connect the scanner’s power connector.
Monitor Switcher 3
Mouse
(Front)
To Imaging Controller
HUB
Power Supply
Keyboard
(Back)
4 Main Control Unit (SP)
34
1
FMPC
distributed by www.minilablaser.com
LP
2.8
Turning on LP5700
Turn on the LP5700.
L2987
35
distributed by www.minilablaser.com
FMPC
2.9
Turning on FMPC and Installing LP5700 Driver
Set the driver CD in the CD drive, then turn on the FMPC. Then log on with following user name and password.
NMP010
User Name: FRONTIER Password: FRONTIER
After the start-up, the “Found New Hardware Wizard” screen appears. Follow the screen instructions to complete the driver installation.
1
36
On the “Found New Hardware Wizard” screen, click the [Next] button.
2
On the “Completing the Found...” screen, click the [Finish] button. This completes the installation of the driver for LP5700 normally.
distributed by www.minilablaser.com
FMPC
2.10
Installing SP-3000 Driver
In FMPC, run and complete “VDEntry” to install the SP-3000 driver.
1
2
3
4
On the “Welcome to the Found...” screen, click the [Next] button.
On the Desktop, select [Start] - [Run], then enter “VDEntry” and then click the [OK] button.
In the “VirtualDriverEntry” dialog box, click the [Regist.] button.
5
When the “Completing the Found New...” screen appears, click the [Finish] button. This completes the SP-3000 driver installation.
After the registration, the following dialog box appears. Click the [OK] button to complete the VDEntry.
37
distributed by www.minilablaser.com
FMPC
2.11
Disabling Network Connection on SP Side
Disable the 1394 network connection on SP side.
1 2
Disconnect the IEEE1394 cable (for connecting to LP5700) from the FMPC. Select [Start] - [Control Panel], then click the [Network Connections].
3 4 5
IMPORTANT Check the settings are done as follows: 1394 Connection on SP: Disabled 1394 Connection on LP: Enabled
38
Right-click on the 1394 Connection whose status is “Enabled”, then set it to “Disabled”. Connect the IEEE1394 cable (for connecting to the LP5700) to the FMPC again. Shut down the FMPC from [Start] - [Shut Down...]
distributed by www.minilablaser.com
FMPC
2.12
1
2
Installing FMPC Software [D20]
Start up the FMPC, the log on to the FMPC PC with the user “FRONTIER” and with the password “FRONTIER”, then insert the installer CD into the CD drive. The installer is automatically started up. If the installer is not stared up, select the executable file “N:\Setup.exe” in the CD drive directly. Procedure Selection [A-001] On the “Procedure Selection [A-001]” screen, select “New Installation”, then click the [Next] button to start installation.
4
5
6
3
Copying of files in CD to HDD is started up.
In the “New Installation Completion [A-020]” dialog box, click the [OK] button.
In the “Setup Completion [A-030]” dialog box, remove the FMPC installer CD from the CD drive, then click the [OK] button to complete the installation.
Starting New Installation [A-010] [Yes]: Starts the new installation. [No]: Returns to the “Procedure Selection [A001]” screen.
IMPORTANT The “Setup Completion (A-030)” dialog box prompts you to install the DI Print/Data Writing Service [C4/C5] successively, but here click the [OK] button to close the installation, because the print size table must be copied first.
39
distributed by www.minilablaser.com
FMPC
2.13
Copying SP-3000 Print Size Table to FMPC
Copy the SP-3000 print size table that was copied to the FD in “2.4 Copying Print Size Table from SP to FD”, to the FMPC.
1
Insert the print size copy tool FD in which the sizes are stored in “2.4”, and then open the “Explorer”, then double-click “PrintSizeSetTool.exe” in FD drive. When the connections are properly done, the following message appears. To start copying, click the [OK] button.
2
3 4
5 2.14
1
40
Another confirmation message appears. Click the [OK] button to start copying.
Data is copied from the FD to FMPC. When copying is completed, the following message appears.
Remove the FD from the FD drive.
Installing DI Print/Data Writing Software [C4/C5] Client in FMPC
Insert the DI Print/Data Writing Software [C4/C5] installer CD into the CD drive of the FMPC, then start the installation.
2
Remove the [C4/C5] installer CD from the CD drive, then restart the FMPC PC.
distributed by www.minilablaser.com
IC
2.15
FMPC
Turning on Imaging Controller
Turn on the Imaging Controller.
C4C509
2.16
Input/Output Device Setup for FMPC
On the “[41F] Installation Information Setup” screen in “Setup and Maintenance”, set “SP-3000 (V1.7-)” to [Input Device], then “LP5700” to [Output Device], then shut down the FMPC PC through the “Post-operational Check”, then start it up again.
41
distributed by www.minilablaser.com
FMPC
2.17
Timer Setup in FMPC
Perform the “[414] Timer Setup” in “Setup and Maintenance” in the FMPC.
1) Select “YES” for “Preheat setting”. • The 1st and 2nd preheat setting boxes appear.
NOTE: The timer ON date/time of the scanner cannot be set.
1
To update “Present time setup”, change the date and time, and click [OK] button.
NOTE: To cancel the update, press the [Cancel] button.
2 3
3) Move the cursor to “2nd Preheat” and enter the time. NOTE:
To change the timer On date and time, check the day of the week and enter the time in the “Timer ON Date/Time Setting” box.
For preheating only once, set the same time for both the first and second times.
• Select “NO” when no preheat timer is used. • The second preheating timer is ignored if the first and second time overlap.
Set the preheat timer by follow the steps below, if necessary. IMPORTANT The ON time for a night-time preheating operation mist not overlap with the ON time of the weekly timer since night-time preheating takes priority and shuts down all power when it is set OFF. If, for instance, the calendar time is set to 5:00 AM and night-time preheating is turned ON at 3:30 AM, all the power will be shut down two hours later at 5:30 AM.
NOTE: Night-time preheating is usually conducted when the room temperature drops below 10°C (50°F) at night and the temperature is not controlled for 8 or more hours.
42
2) Move the cursor to “1st Preheat” and enter the time.
1st. preheat time: 2:00 AM 2nd. Preheat time: 3:00 AM With the above settings, nighttime preheating will occur from 2:00 AM to 4:00 AM (2 hours).
4
Click the [OK] button.
• Operation returns to the menu screen.
distributed by www.minilablaser.com
FMPC
2.18
Installation Information Setup in FMPC
Perform “[41F] Installation Information Setup” in “Setup and Maintenance” in the FMPC.
1
SP
Enter the same Delivery Date and Startup Date as the dates set in “[0140] Installation Information Setup” in the SP-3000.
2 3 4
Click the [OK] button. On the confirmation dialog box, click the [OK} button. After the setup, shut down the FMPC PC through the “Post-operational Check”, then start it up again.
NOTE: Make sure to restart the FMPC.
2.19
Paper Condition Setup
Perform “[421] Paper Condition Setup” in “Setup and Maintenance” in the FMPC. IMPORTANT Make sure to perform the paper condition setup for all paper to be used.
43
distributed by www.minilablaser.com
IC
2.20
FMPC Output Device Setting in Imaging Controller
Register the FMPC output device in the Imaging Controller.
■ Setup Example is DI Print/Data Writing [C4/C5] [Selection] “Print Service - Administration” - ”Output Device” Set up “sRGBFMPC” and “PDFMPC” for [Device].
IMPORTANT Installing of DI Import/Export Driver Software [C2} must be required. The default device names for “FMPC” are “sRGBFMPC” and “PDFMPC”.
44
distributed by www.minilablaser.com
IC
2.21
FMPC
Operational Check
Perform the film printing in the FRONTIER, then the DSC printing from Imaging Controller to check the operation.
3
In the [INPUT] field, click the icon of the media you inserted. Click the icon of the media you inserted.
(1) Printing from Imaging Controller [Imaging Controller Operation]
1
Set the media in the drive.
4
On the DSC Print Service screen, select the folder in which the images are stored. Select the folder.
FD121
2
In the [OUTPUT] field, select the FRONTIER device.
5
Select the images to be printed. Select the images.
Click the [Set] button.
6
Click the [Set] button. The image files are listed
45
distributed by www.minilablaser.com
IC
10
up in the [Order Specification Column].
FMPC
Registering of order is completed.
Click the [Set] button.
7
[FMPC Operation]
The ”Confirmation” dialog appears.
11
8
Remove the media from the drive.
12 FD124
9
Click the [OK] button.
Click.
13
46
On the Main Menu screen, select [2 Print], then click the [OK] button.
After the printing is completed, the order is
In the [Next Print] list on the “Print Status Notice” screen, the DI order with the status “Printing” is displayed, and then it is printed.
distributed by www.minilablaser.com
SP
moved to the [Done] list.
FMPC
15
Click the [Main Menu] button.
16
Control returns to the “Main Menu” screen.
[Sheets being processed] on the lower right-hand side of the screen shows where the current order is being processed.
14
After the printing is completed, click the [Next Order Stop] button.
(2) Printing from FRONTIER If the [Resume] button appears at the bottom of the screen, click it to switch to the [Next Order Stop] button. Then printing is started.
• The images of the first 6 frames appear on the screen.
47
distributed by www.minilablaser.com
SP
To skip the frames (not to be printed), select the frames, then press the [PASS] key.
2
Proceed with scanning of the images. IMPORTANT Do not touch the film while it is being fed through the carriage. Pulling out the film at this time will cause abnormal printing results.
• When the last frame is scanned, the “Order Data Display” dialog box appears automatically.
1
Press the [START/ENTER] key if the film feed mode is “Semi”.
• One-way scanning mode: The film is ejected from the right-hand side of the film carrier.
If the [Scan Cancel] key is pressed during prescanning, the order is not fixed automatically. To fix such orders, press the [Sort/Order] button.
• The message shown below appears.
Z2569
• Two-way scanning mode: The film is ejected from the left-hand side of the film carrier.
Z2065
• The green indicator lamp blinks when the finescanning is completed.
Indicator Lamp ZII062
48
distributed by www.minilablaser.com
FMPC
IMPORTANT The orders that are registered in the FMPC cannot be deleted with the [Print Stop] key. To delete them, select orders one by one, then click the [Cancel] button on the printing status screen.
5
In the [Next Print] list on the “Print Status Notice” screen, the film order with the status “Printing” is displayed, and then it is printed.
[FMPC Operation]
3
Press the button of the switcher to display the FMPC main menu screen. Also by pressing the [Ctrl] key twice quickly, the display can be switched between FRONTIER and FMPC.
MP019
4
On the Main Menu screen, select [2 Print], then click the [OK] button.
6
After the printing is completed, the order is moved to the [Done] list.
[Sheets being processed] on the lower right-hand side of the screen shows where the current order is being processed.
49
distributed by www.minilablaser.com
IC
7
8
After the printing is completed, click the [Next Order Stop] button.
9
SP
FMPC
Control returns to the “Main Menu” screen.
Click the [Main Menu] button.
2.22
Creating Backup FD for FMPC/SP-3000
Create a backup FD for FMPC/SP-3000. (See “2.3.3 Creating Backup FD for SP-3000 and LP5700”)
2.23
System Shutdown
Shut down the SP-3000, FMPC, then Imaging Controller in this order. This completes the FMPC installation and setup.
50
distributed by www.minilablaser.com
3
Installation for FRONTIER 355/375
FMPC
Install the FMPC devices and software, and set them up for use.
3.1
Installation Procedure List
Install the FMPC using the following procedure. [New Installation] No. 1 2 3 4 5 6 7 8 9
10
11 12 13 14 15 16 17 18 19
20 21 22 23 24 25
Procedures IEEE1394 Board Installation PC Preparations Disabling of “Rack Auto Cleaning” Creating Backup FD for SP-3000 and LP1500/2000 Replacing the ROM for Printer Connecting FMPC, FRONTIER, LAN Cable and Monitor Switcher Turning on FMPC Disabling Network Connection on SP Side IEEE1394 Driver Installation in SP(Ver.1.5 only) When the scanner (SP) has the System [A1] Ver.1.7, installing or updating of driver in SP is not required. [A1] Stand-alone Version-Up [Ver.1.5 -> Ver.1.7] and DI Print/Data Writing Software [C4/C5] Client Installation in SP IEEE1394 Driver Pre-installation Installing IEEE1394 Driver for SP in FMPC Starting-up LP in ROM Mode and Checking ROM Version (2.0-0X-000) Installing IEEE1394 Driver for LP in FMPC FMPC [D20] Installation (Reinstall) with Printer’s Backup FD DI Print/Data Writing Software [C4/C5] Client Installation in FMPC Installation Information Setup for FMPC Output Device Setup for SP and Restarting SP Copying Print Size Table to FD then Copping SP-3000 Print Size Table to FMPC (In use of 3KPrintsizeCopyTool) FMPC Output Device Setting in Imaging Controller Enabling of “Rack Auto Cleaning” Paper Condition Setup Creating Backup FD for FMPC, SP-3000 and LP1500/2000 Operational Check System Shutdown
FMPC FMPC SP SP
Location
Refer to See Section 2.2.1 on page 15 See Section 3.2 on page 53 See Section 3.3 on page 53 See Section 3.4 on page 54
LP SP,LP,FMPC, Monitor Switcher
See Section 3.5 on page 55 See Section 3.6 on page 56
(PW: FRONTIER) FMPC FMPC SP
See Section 3.7 on page 60 See Section 3.8 on page 60 See Section 3.9 on page 60
SP
See Section 3.10 on page 61
FMPC FMPC LP
See Section 3.11 on page 63 See Section 3.12 on page 64 See Section 3.13 on page 65
FMPC FMPC
See Section 3.14 on page 65 See Section 3.15 on page 66
FMPC
See Section 3.16 on page 69
FMPC SP
See Section 3.17 on page 70 See Section 3.18 on page 70
SP/FMPC
See Section 3.19 on page 71
IC
See Section 3.20 on page 72
SP FMPC FMPC/SP/LP
See Section 3.21 on page 73 See Section 3.22 on page 73 See Section 3.23 on page 74
FMPC/SP/LP/IC SP/FMPC/IC
See Section 3.24 on page 75 See Section 3.25 on page 75
PC Preparations Perform “(14) “Visual Notification” to ON in Dr. Watson Dialog Box” and (15) Non-display setting of Internet Explorer Dialog Box” in “2.2.7 Windows Settings”.
FMPC
See Section 3.2 on page 53
2
Disabling of “Rack Auto Cleaning”
SP
See Section 3.3 on page 53
3
Creating Backup FD for SP-3000, LP1500/2000 and FMPC
SP/LP
See Section 3.4 on page 54
4
Turning on FMPC
(PW: FRONTIER) FMPC
See Section 3.7 on page 60
5
IEEE1394 Driver Pre-installation in SP(Ver.1.5 only) When the scanner (SP) has the System [A1] Ver.1.7, installing or updating of driver in SP is not required.
SP
See Section 3.9 on page 60
6
[A1] Stand-alone Version-Up [Ver.1.5 -> Ver.1.7] and DI Print/Data Writing Software [C4/C5] Client Installation in SP
SP
See Section 3.10 on page 61
7
Inserting the IEEE1394 Driver Disk then Restarting FMPC
FMPC
See Section 3.11 on page 63
8
IEEE1394 Driver for SP Installation in FMPC
FMPC
See Section 3.12 on page 64
9
Starting-up LP in ROM Mode and Checking ROM Version (2.0-0X-000)
LP
See Section 3.13 on page 65
10
IEEE1394 Driver for LP Installation in FMPC
FMPC
See Section 3.14 on page 65
11
FMPC [D20] Installation (User Version-up)
FMPC
See Section 3.15 on page 66
12
Enabling of “Rack Auto Cleaning”
SP
See Section 3.21 on page 73
13
Paper Condition Setup
FMPC
See Section 3.22 on page 73
14
Creating Backup FD for FMPC, SP-3000 and LP1500/2000
(See “2.2 PC Preparations”) For the installing procedures for 1394 board, See “2.2.1 IEEE1394 Board Installation”.
3.3
Disabling of “Rack Auto Cleaning”
To minimize the waiting time for installation, select “No” for “Rack Auto Cleaning” in “[46B] Processor Operating Condition Setup”.
Select “No”.
NOTE: After the settings are completed, set to “Yes” again.
53
distributed by www.minilablaser.com
SP
3.4
Creating Backup FD for SP-3000 and LP1500/2000
The data backup FD should be kept in a fixed place near the machine because it is used after recovering from trouble or when installing FMPC.
5
6 1 2 3 4
Insert the floppy disk into the drive of the main control unit.
Click the [OK] button.
Select [Setup and Maintenance] - [01 System Operation Setup and Check] - [0122 Data Backup] Prepare a floppy disk for data backup when backing up film scanner or printer processor data.
7
Upon completion of the backup, click the [Cancel] button.
• Operation returns to the menu screen. Move the cursor to the "Destination" box and select “Film Scanner” or “Printer processor”.
8
Remove the floppy disk from the disk drive.
Click the [OK] button. IMPORTANT If FRONTIER has the system [A1] Ver.1.5 or Ver.1.6, insert the 1394 Driver Disk for SP-3000 (See “1.2 Checking the Kit Contents”), then perform the post-operational check.
• “Making the backup of the data” message appears.
9 10
54
FMPC
Perform the post-operational checks. In case of updating, use the same procedures as the above to perform creating backup FD for FMPC.
distributed by www.minilablaser.com
LP
3.5
Replacing the ROM for Printer
3
[ROM Replacement] Replace the ROM on the CTL 20 circuit board with adaptable ROM for FMPC.
1 2
Remove the five screws and open the control CB bracket.
Turn the power switch to STANDBY, and turn OFF the built-in circuit breaker and the main supply. Remove the 14 screws and then take off the printer control section cover. Screws (14)
Control Circuit Board Bracket
4
Printer Control Section Cover
Screws (5)
EZ177
Replace the ROM U16 (40 pins) on the CTL 20 circuit board with the adaptable ROM for FMPC.
EZ783
FMPC Adaptable ROM 4D005+*
55
distributed by www.minilablaser.com
SP
3.6
FMPC
Connecting FMPC, FRONTIER, LAN Cable and Monitor Switcher
3
(1) IEEE1394 Cable Preparation
Bind the bared part of the cable with insulating tape.
Bind the bared part of the existing IEEE1394 cable connected between the printer (LP) and scanner (SP).
1
LP
Clamp
Disconnect the IEEE1394 cable from the scanner (SP).
Insulating Tape IEEE1394 Cable MP006
MP047
2
56
Remove the clamp from the cable.
distributed by www.minilablaser.com
SP
LP
FMPC
(2) IEEE 1394 Cable Connection Preparations The connection from LP (printer) and SP (scanner) is as shown below. But in this step, do not connect them to the FMPC. IMPORTANT Do not connect the two cables to the same board in the FMPC..
Scanner (SP)
Printer (LP)
Existing IEEE1394 Cable (10m)
IEEE1394 Cable (4.5m)
IMPORTANT Make sure that the IEEE1394 cable from scanner (SP) is connected to the lower board, and the cable from printer (LP) to the upper board.
57
distributed by www.minilablaser.com
SP
LP
FMPC
(3) Monitor Switcher Connections Connect the FMPC, monitor switcher, and FRONTIER as follows. It is recommended that the monitor switcher be installed on the main control unit.
MP046
By placing the full keyboard as shown above, you can press the [Ctrl] key easily to switch the display.
58
distributed by www.minilablaser.com
SP
LP
FMPC
(4) Other Connections Connect the FMPC, FRONTIER and the monitor switcher and then connect the LAN cable from the HUB to which the Imaging Controller is connected. as shown in the following connection diagram.
FRONTIER (SP) 4
5
3
1
2 IMPORTANT Connect the monitor’s power cable to the power supply directly. Do not connect the scanner’s power connector.
Monitor Switcher 3
Mouse
(Front)
To Imaging Controller
HUB
Power Supply
Keyboard
(Back)
4 Main Control Unit (SP)
1
FMPC
59
distributed by www.minilablaser.com
FMPC
3.7
Turning on FMPC
Turn on the FMPC, with the password “FRONTIER”. NOTE: If the scanner's system disk version is 1.7, the above procedure is not necessary.
3.8
Disabling Network Connection on SP Side
Select [Start] - [Control Panel] - [Network Connections], then disable the 1394 network connection on SP side.
1
Select [Start] - [Control Panel], then click the [Network Connections].
3.9
2
2
3
After the SP is restarted, perform the preinstallation following the screen instructions.
Connect the FMPC to scanner (SP) with the 1394 cable. Restart the SP.
4
60
Right-click on the 1394 Connection whose status is “Enabled”, then set it to “Disabled”.
IEEE1394 Driver Installation in SP
Perform the pre-installation of the IEEE1394 driver in the scanner (SP). if the version of system disk [A1] in scanner is Ver.1.7, this procedures are not necessary.
1
IMPORTANT Check the setting as follows: 1394 Connection on SP: Disabled 1394 Connection on LP: Enabled
Replace the CD with the FRONTIER 355/375 System Software [A1] CD, then restart the SP.
distributed by www.minilablaser.com
SP
5
Perform the driver installation following the Wizard. (See “3.10 A1 Stand-alone Version-up in SP”) The following drivers are installed. • EZ2 1394 Device (for Scanner) • 1394 Client Device (for Printer)
3.10
[A1] Stand-alone Version-up and DI Print/Data Writing Software Installation in SP
If the scanner’s system disk version is 1.7, the following procedures are not necessary.
1
2
3
Select "Update stand-alone scanner", then click the [Next >] button.
When the following "(L-001) Simple Upgrade" screen appears after the SP(A1) is started up, click the [OK] button.
4
Click the [Yes] button.
5
Click the [Next >] button.
Select "SE maintenance", then click the [Next >] button.
61
distributed by www.minilablaser.com
SP
6
Select "Inherit data from HD", then click the [Next >] button.
After upgrading of A1 is completed, the SP(A1) is restarted. NOTE: The connection error message may appear after restarting, but this causes no problems.
9
7
Click the [OK] button.
8
Click the [OK] button.
62
Insert the DI Print/Data Writing Software [C4/C5] installer CD into the CD drive of the FMPC, then start the installation.
distributed by www.minilablaser.com
FMPC
3.11
1
IEEE1394 Driver Pre-installation
Insert the FMPC driver CD into the CD-ROM, then in the “Device Drivers Disk [D-01]” dialog box, click the [OK] button. This completes the FMPC driver disk setup. If the driver disk is not started up automatically, run “N:\EZ171\Setup.exe.” (“N:\” varies depending on your system.)
2
When the FMPC driver disk setup is completed normally, the “Device Drivers Disk [D-02]” dialog box appears. Remove the driver disk from the CD-ROM drive, then click the [OK] button to shut down the system. After shutdown, turn on the FMPC.
NOTE: If the FMPC Ver.1.0 is already installed, start up the FMPC while pressing the [Shift] key. (Start pressing the [Shift] key just when the Windows XP logo appears.)
63
distributed by www.minilablaser.com
FMPC
3.12
Installing IEEE1394 Driver for SP in FMPC
In FMPC, run and complete “VDEntry” to install the SP-3000 driver.
1
2
3
64
4
On the “Welcome to the Found...” screen, click the [Next] button.
On the Desktop, select [Start] - [Run], then enter “VDEntry” and then click the [OK] button.
In the “VirtualDriverEntry” dialog box, click the [Regist.] button.
After the registration, the following dialog box appears. Click the [OK] button to complete the VDEntry.
5
When the “Completing the Found New...” screen appears, click the [Finish] button. This completes the SP-3000 driver installation.
distributed by www.minilablaser.com
LP
3.13
1
Starting-up LP in ROM Mode and Checking ROM Version (2.0-0x-000)
Start up the Printer (LP) in the ROM mode. While counting-down is in progress, press [MENU] [<-] - [->] - [Enter] in this order, then check that the ROM version is displayed on the panel, and then check if the ROM Version is “(2.0-0x-000)”. [ ROM Version 2.0-0X-000
3.14
1 2
3
FMPC
] >
Installing IEEE1394 Driver for LP in FMPC
Connect the IEEE1394 cable from the printer (LP) to the connector of the upper board in FMPC.
4 5
On the “Found New Hardware Wizard” screen, click the [Next] button.
Remove the all checkmarks, then click the [Next] button.
6
7
New driver is installed. On the “Completing the Found...” screen, click the [Finish] button. This completes the installation of the driver for LP5700 normally.
Check if the device name “1394 Client Device (for printer)” is displayed on the “Device Manager” screen.
This completes the FMPC driver installation.
65
distributed by www.minilablaser.com
FMPC
3.15
FMPC [D20] Installation (Reinstall) with Printer’s Backup FD
NOTE: Make sure that the ROM version is displayed on the operation panel in the printer (LP).
1
3
Select [Re-Installation], then click the [Next >] button.
Insert the FMPC installer CD into the CD drive, then restart the FMPC.
In case of updating from Ver.1.0 to Ver.2.0, select "User Version up". NMP012
2
4
Click the [Yes] button.
5
Click the [OK] button.
The FMPC installer program is automatically started up. If the installer program is not started up, perform the following procedures.
(1) Move to [EZ171] folder in the CD drive. (2) Double-click [setup.exe].
66
distributed by www.minilablaser.com
FMPC
6
On the “Printers Selection (A-113)” screen, select [LP1500/LP2000], then click the [Next] button.
7
Installation is started.
8
Click the [Yes] button.
11
“Information” dialog box appears.
12
Insert the LP backup FD into the FD drive.
NMP014
13 9
Click the [OK] button.
Click the [No] button.
14
On the “Input Source Selection [A-135]” screen, select [SP3000 (V1.7-)], then click the [Next] button.
NOTE: In this case, select [No] because the FMPC backup FD is not prepared yet.
10
Click the [Yes] button.
67
distributed by www.minilablaser.com
FMPC
15
Click the [OK] button.
16
Click the [OK] button.
18
Remove the CD from the CD drive.
NMP013
IMPORTANT Do not start up the LP. If is is started, the LP parameters are initialized.
17
Remove the FD from the FD drive.
19
NMP015
68
Proceed to “3.16 DI Print/Data Writing Software Installation in FMPC”.
distributed by www.minilablaser.com
FMPC
3.16
1 2
3
DI Print/Data Writing Software [C4/C5] Client Installation in FMPC
Insert the DI Print/Data Writing [C4/C5] installer CD into the CD drive, then restart the FMPC.
5
The C4/C5 installer program is automatically started up. If the installer is not started up, double-click [setup.exe]. Enter the Imaging Controller name, then click the [Next >] button.
6 7
4
After the installation is completed, the “InstallShield Wizard Complete” screen appears.
Remove the installer CD from the CD drive. On the “InstallShield Wizard Complete” screen, select “Yes, I will restart ...”, then click the [Finish] button.
Click the [Next >] button.
69
distributed by www.minilablaser.com
FMPC
3.17
1
SP
Installation Information Setup for FMPC
Select “1) System Condition Setup and Check” - “2) Installation Information Setup”,then set up the “Delivery Date” and “Setup Date”, and then click the [OK] button.
You can check the delivery and startup dates for printer in the "41F Installation Information Setup" on the SP.
3.18
1
70
Output Device Setup for SP and Restarting SP
Restart the SP(Scanner), then open "Setup and Maintenance" - "System Condition Setup and Check" - "Installation Information Setup", and select "FMP Controller" as Output Device, then click the [OK] button.
2
Restart the SP. IMPORTANT To activate the settings, the SP must be restarted.
distributed by www.minilablaser.com
SP
3.19
Copying Print Size Table to FD then Copying SP-3000 Print Size Table to FMPC
Copy the print size table from the SP to the FD by using the dedicated print size copy tool. Then, copying it to the FMPC
NOTE: “3KPrintSizeCopyTool” changes the size settings for LP1500/2000 to those for LP5700. Although SP3000 ver.1.7 has both the tables for LP1500/2000 and LP5700, the FMPC system use the latter only. So the settings for LP1500/2000 must be changed to those for LP5700 using this tool.
(1) Running of “3KPrintsizeCopyTool”
1
Insert the print size setting tool FD into the FD drive of SP, then select [Setup and Maintenance] -> [Special Operation] -> [Explorer], and then double-click “3KPrintsizeCopyTool.exe” in the [F355_375] folder in the FD drive.
(2) Copy Table to FD
1
2
2
3
4
FMPC
On the copy starting screen, click the [Yes] button.
3
Insert the print size setting tool FD into the FD drive of SP, then select [Setup and Maintenance] -> [Special Operation] -> [Explorer], and then execute "PrintSizeTool.exe" in the FD. When the FRONTIER model and System [A1] is proper, the following message appears. Click the [OK] button to start copying it to the system.
After copying, remove the FD from the FD drive, then click the [OK] button.
After the copy is done, click the [Yes] button in the confirmation dialog box.
In the completion dialog box, click the [OK] button.
71
distributed by www.minilablaser.com
FMPC
(3) Copy Table from FD to FMPC
1
Copy the print size table to FMPC. On the FMPC, open [Setup and Maintenance] -> [Special Operation] -> [Explorer], then doubleclick “PrintSizeSetTool.exe” in FD drive. When the connections are properly done, the following message appears. To start copying, click the [OK] button.
2
3 4
3.20
Another confirmation message appears. Click the [OK] button to start copying.
Data is copied from the FD to the FMPC. When copying is completed, the following message appears.
FMPC Output Device Setting in Imaging Controller
Register the FMPC output device in the Imaging Controller. (For details of setting, see each manual.)
■ Setup Example is DI Print/Data Writing [C4/C5] [Selection] [Print Service - Administration] - [Output Device]
The default device names for “FMPC” are “sRGBFMPC” and “PDFMPC”. CAUTION Installing of DI Import/Export driver software must be installed. The output device name is automatically transferred to the Imaging Controller when opening the "Print Status Notice" screen in FMPC.
Set up “sRGBFMPC” and “PDFMPC” for [Device].
72
IC
distributed by www.minilablaser.com
FMPC
3.21
Enabling of “Rack Auto Cleaning”
Since the installation process is completed, return “Rack Auto Cleaning” to “Yes” in “[46B] Processor Operating Condition Setup”.
3.22
Paper Condition Setup
Set up the paper condition in the FMPC. NOTE: After the installation is completed, perform the condition setup for all magazines.
73
distributed by www.minilablaser.com
SP
3.23
Creating Backup FD for FMPC, SP-3000 and LP1500/2000
3
Back up the data both in the FMPC and FRONTIER. The following procedures are those used for the
4
Move the cursor to the “Destination” box and select “MP Controller” or “Printer” Click [OK]
FMPC. Also, perform the same procedures for the
• “Making the backup of the data” message appears.
FRONTIER.
[Selection] “4 Setup and Maintenance” - “1 System Operation Setup and Check” - “7 Data Backup”
[Procedure] Make a backup of unit data stored in the hard disk of the main control unit after changing the “Setup and Maintenance” data in case unit data is damaged.
1
5
• Operation returns to the “4 Setup and Maintenance” screen.
Prepare the data backup floppy disk “FMP Controller” or “LP1500/LP2000”
6
2
Insert the disk into the floppy drive of the main control unit.
NMP014
74
Upon completion of the backup, press the [Cancel] button.
Remove the FD from the drive.
NMP015
distributed by www.minilablaser.com
IC
3.24
SP
FMPC
Operational Check
Perform the operational check. (See “2.21 Operational Check”.)
3.25
System Shutdown
Shut down the SP-3000, FMPC, then Imaging Controller in this order. This completes the FMPC installation and setup.
75
distributed by www.minilablaser.com
4
Installation for FRONTIER 350/370
FMPC
Install the FMPC devices and software, and set them up for use.
4.1
Installation Procedure List
Install the FMPC using the following procedure. [New Installation] No.
Procedures
Refer to
IEEE1394 Board Installation
FMPC
See Section 2.2.1 on page 15
2
PC Preparations
FMPC
See Section 4.2 on page 78
3
Disabling of “Rack Auto Cleaning”
SP
See Section 4.3 on page 78
4
Creating Backup FD for SP-3000, LP1500/ 2000
SP/LP
See Section 4.4 on page 79
5
Replacing the ROM for Printer
LP
See Section 4.5 on page 80
6
Connecting FMPC, FRONTIER, LAN Cable and Monitor Switcher
SP,LP,FMPC, Monitor Switcher
See Section 4.6 on page 81
7
Turning on FMPC (PW: FRONTIER)
FMPC
See Section 4.7 on page 85
8
Disabling Network Connection on SP Side
FMPC
See Section 4.8 on page 86
9
[A1] Stand-alone Version-Up in SP and DI Print/Data Writing Software [C4/C5] Client Installation in SP
SP
See Section 4.9 on page 87
10
IEEE1394 Driver Preinstallation
FMPC
See Section 4.10 on page 89
11
Installing IEEE1394 Driver for SP in FMPC
FMPC
See Section 4.11 on page 90
12
Starting-up LP in ROM Mode and Checking ROM Version (2.0-0X-000)
LP
See Section 4.12 on page 90
13
Installing IEEE1394 Driver for LP in FMPC
FMPC
See Section 4.13 on page 91
14
FMPC [D20] Installation (Reinstall) with Printer’s Backup FD
FMPC
See Section 4.14 on page 92
15
DI Print/Data Writing Software [C4/C5] Client Installation in FMPC
FMPC
See Section 4.15 on page 95
16
Installation Information Setup for FMPC
FMPC
See Section 4.16 on page 96
17
Output Device Setup for SP and Restarting SP
SP
See Section 4.17 on page 97
18
Copying Print Size Table to FD then Copping LP1500/2000 Print Size Table to FMPC
SP/FMPC
See Section 4.18 on page 98
19
FMPC Output Device Setting in Imaging Controller
IC
See Section 4.19 on page 99
20
Enabling of “Rack Auto Cleaning”
SP
See Section 4.20 on page 99
21
Paper Condition Setup
FMPC
See Section 4.21 on page 99
22
Creating Backup FD for FMPC, SP1500/2000 and LP1500/2000
PC Preparations Perform “(14) “Visual Notification” to ON in Dr.Watson Dialog Box” and “(15) Nondisplay setting of Internet Explorer Dialog Box” in “2.2.7 Windows Settings”.
FMPC
Location
See Section 4.2 on page 78
Refer to
2
Disabling of “Rack Auto Cleaning”
SP
See Section 4.3 on page 78
3
Creating Backup FD for SP1500/2000, LP1500/2000 and FMPC
SP/LP
See Section 4.4 on page 79
4
Turning on FMPC(PW: FRONTIER)
FMPC
See Section 4.7 on page 85
5
[A1] Stand-alone Version-Up in SP with DI Print/Data Writing Software [C4/C5] Client Installation
SP
See Section 4.9 on page 87
6
Restarting SP (Connection error message may appear after restarting, but this causes no problems )
SP
7
IEEE1394 Driver Pre-installation
FMPC
8
Installing IEEE1394 Driver for SP in FMPC
FMPC
See Section 4.11 on page 90
9
Starting-up LP in ROM Mode and Checking ROM Version (2.0-0X-000)
LP
See Section 4.12 on page 90
10
Installing IEEE1394 Driver for LP in FMPC
FMPC
See Section 4.13 on page 91
11
FMPC [D20] Installation (User Version-up)
FMPC
See Section 4.14 on page 92
12
Restarting FMPC
FMPC
13
Enabling of “Rack Auto Cleaning”
SP
See Section 4.20 on page 99
14
Paper Condition Setup
FMPC
See Section 4.21 on page 99
15
Creating Backup FD for FMPC, SP1500/2000 and LP1500/2000
(See “2.2 PC Preparations”) For the installing procedures for 1394 board, See 2.2.1 IEEE1394 Board Installation .
4.3
Disabling of “Rack Auto Cleaning”
To minimize the waiting time for installation, select “No” for “Rack Auto cleaning” in “[46B] Rack Auto Cleaning”. (In case of updating from FMPC Ver.1.0, perform this setting in FMPC.)
After the installation, set to No again.
78
SP
distributed by www.minilablaser.com
SP
4.4
1 2
Creating Backup FD for SP1500/2000, LP1500/2000
Set to “No” for “Rack Auto Cleaning.
6
Click [OK].
• “Making the backup of the data” message appears.
Select “4 Setup and Maintenance” - “1 System Operation Setup and Check ” - “7 Data Backup ”
7 8 3 4 5
FMPC
Prepare a data backup floppy disk “SP1500/ SP2000” or “LP1500/LP2000”.
Upon completion of the backup, press the [Cancel] button. Insert the FRONTIER 350/370 System (A1) Disk into the CD-ROM drive. FRONTIER 350/370 System Disk (A1)
Insert a disk into the floppy drive of the main control unit. Move the cursor to the “Destination” box and select “Scanner”, “Printer” or “Pricing Unit”.
NOTE: Perform pricing data backup into the hard disk when pricing unit data is changed.
GD1621
9 10
Perform the post-operational checks, then shut down the FRONTIER. In case of updating, use the same procedures as the above to perform creating backup FD for FMPC.
79
distributed by www.minilablaser.com
LP
4.5
Replacing the ROM for Printer
4
[ROM Replacement] Replace the ROM on the CTL 20 circuit board with an adaptable ROM for FMPC.
1 2
Replace the ROM U16 (40 pins) on the CTL 20 circuit board with the adaptable ROM for FMPC.
Set the power switch to STANDBY, and turn OFF the built-in circuit breaker and the main supply. Remove the fourteen screws and then take off the printer control section cover. Screws (14)
FMPC Adaptable ROM 4D005+*
5
Printer Control Section Cover
3
Remove the five screws and open the control CB bracket.
Control Circuit Board Bracket
80
EZ783
Screws (5) EZ177
Close the control CB bracket, and then reinstall the printer control section cover.
distributed by www.minilablaser.com
FMPC
4.6
LP
Connecting FMPC, FRONTIER, LAN Cable and Monitor Switcher
4
(1) IEEE1394 Cable Preparation
Bind the bared part of the cable with insulating tape.
Bind the bared part of the existing IEEE1394 cable connected between the printer (LP) and scanner (SP).
1
SP
Clamp
Remove the scanner rear cover by loosening the four screws and removing the fifteen screws. Screws(15)(Remove)
Insulating Tape IEEE1394 Cable MP006
Scanner Rear Cover Screws(4)(Loosen) EZ900
2
Remove the clamp screw and then disconnect the IEEE1394 cable from the scanner (SP). Clamp Screw IEEE1394 Cable
MP004
3
Remove the clamp from the cable.
81
distributed by www.minilablaser.com
FMPC
SP
LP
(2) IEEE 1394 Cable Connection Preparations
1 2
Connect the Printer (LP) to the FMPC with the existing IEEE1394 cable (10m) that connected the Printer (LP) to the Scanner (SP). Connect the Scanner (SP) to the FMPC with the IEEE1394 cable (4.5m). IMPORTANT Do not connect the two cables to the same board in the FMPC.
Scanner (SP)
Printer (LP)
Existing IEEE1394 Cable (10m)
IEEE1394 Cable (4.5m)
FMPC
IEEE1394 Connectors IMPORTANT Make sure that the IEEE 1394 cable from scanner (SP) is connected to the lower board, and the cable from printer (LP) to the upper board.
82
distributed by www.minilablaser.com
FMPC
SP
LP
(3) Monitor Switcher Connections Connect the FMPC, monitor switcher, and FRONTIER as follows. It is recommended that the monitor switcher be installed under the monitor. Monitor
Scanner (SP)
Monitor Switcher MP007
83
distributed by www.minilablaser.com
FMPC
SP
LP
(4) Other Connections Connect the FMPC, FRONTIER and the monitor switcher and then connect the LAN cable from the HUB to which the Imaging Controller is connected. as shown in the following connection diagram.
FRONTIER (SP) 5
3
5
1 4 2
IMPORTANT Connect the monitor’s power cable to the power supply directly. Do not connect the scanner’s power connector.
Monitor Switcher 3
Keyboard Cable from the SP Extension Cable for Keyboard
Mouse
(Front)
To Imaging Controller
Power Supply HUB 2
(Back) 1
Keyboard Main Control Unit (SP) 4
FMPC
84
distributed by www.minilablaser.com
FMPC
SP
LP
(5) Cable Routing After the connections are completed, route the cables from FRONTIER as shown below. Mouse Cable Serial Cable for Monitor Switcher LAN Cable
Keyboard Cable Cable Bracket Keyboard/Mouse Cable from the front Keyboard Extention Cable MP016
4.7
Turning on FMPC
Turn on the FMPC, then log on with the password “FRONTIER”.
NMP010
IMPORTANT If the FMPC Ver.1.0 is already installed, start up the FMPC while pressing the [Shift] key. (Start pressing the [Shift] key just when the Windows XP logo appears.)
85
distributed by www.minilablaser.com
FMPC
4.8
Disabling Network Connection on SP Side
Disable the 1394 network connection on SP side.
1 2
Select [Start] - [Control Panel], then click the [Network Connections]. Right-click on the 1394 Connection whose status is “Enabled”, then set it to “Disabled”.
IMPORTANT Check the setting as follows: 1394 Connection on SP: Disabled 1394 Connection on LP: Enabled
86
3
Set to "Disabled" for another connection using the same procedure. The number of connection varies depending on your system.
distributed by www.minilablaser.com
FMPC
4.9
1
[A1] Stand-alone Upgrade in SP [Ver.1.5 -> Ver.1.7] and DI Print/Data Writing Software [C4/C5] Client Installation in SP
Press the scanner’s START switch to start up the FRONTIER.
4
Select “Update stand-alone scanner”, and click the [Next] button.
• The installer starts and the “[L-001] Simple Upgrade” screen appears.
2
In the confirmation dialog, click the [Yes] button.
6
Click the [Next] button.
Click the [OK] button.
• The “Procedure Selection 1 [C-001]” screen appears.
3
5
Select “SE maintenance” and click the [Next] button.
• The “Procedure Selection 2 [C-002]” screen appears.
87
distributed by www.minilablaser.com
FMPC
• Copying starts.
9
10
In the complete dialog, click the [OK] button.
Remove the CD from the CD drive, then restart the scanner (SP).
NOTE: The connection error message may appear after restarting, but this causes no problems.
7
8
Select “Inherit data from former version on HD”, and click the [Next] button.
11
Insert the DI Print/Data Writing Software[C4/C5] installer CD into the CD drive of the FMPC, then start the installation.
In the confirmation dialog, click the [OK] button. After restarting, the connection error message may appear, but this causes no problems.
88
distributed by www.minilablaser.com
FMPC
4.10
1
IEEE1394 Driver Pre-installation
Insert the FMPC driver CD into the CD-ROM, then in the “Device Drivers Disk [D-01]” dialog box, click the [OK] button. This completes the FMPC driver disk setup. If the driver disk is not started up automatically, run “N:\EZ171\Setup.exe.” (“N:\” varies depending on your system.)
2
When the FMPC driver disk setup is completed normally, the “Device Drivers Disk [D-02]” dialog box appears. Remove the driver disk from the CD-ROM drive, then click the [OK] button to shut down the system. After shutdown, turn on the FMPC.
NOTE: If the FMPC Ver.1.0 is already installed, start up the FMPC while pressing the [Shift] key. (Start pressing the [Shift] key just when the Windows XP logo appears.)
89
distributed by www.minilablaser.com
FMPC
4.11
1
2
Installing IEEE1394 Driver for SP in FMPC On the Desktop, select [Start] - [Control Panel] [System] - [Hardware] tab - [Device Manager], and then check if “1394 Client Device (For Scanner)” exists under “1394 Client Device”.
On the “Completing the Found...” screen, click the [Finish] button. This completes the installation of the driver for LP-5700 normally.
Starting-up LP in ROM Mode and Checking ROM Version (2.0-0x-000)
Start up the printer (LP) in the ROM mode. During the countdown press [MENU - [<-] - [->] - [Enter] in this order, then check that the ROM Version is displayed on the panel, then check if the ROM Version is “(2.0-0x000)”. [ ROM Version 2.0-0X-000
90
3
On the “Found New Hardware Wizard” screen, click the [Next] button.
4.12
1
LP
] >
distributed by www.minilablaser.com
FMPC
4.13
1
2
Installing IEEE1394 Driver for LP in FMPC
On the “Found New Hardware Wizard” screen, click the [Next] button.
3
On the Desktop, select [Start] - [Control Panel] [System] - [Hardware] tab - [Device Manager], and then check if “1394 Client Device (For Printer)” exists under “1394 Client Device”.
On the “Completing the Found...” screen, click the [Finish] button. This completes the installation of the driver for LP-5700 normally.
91
distributed by www.minilablaser.com
FMPC
4.14
FMPC [D20] Software Installation (Reinstall) with Printer's Backup FD
Install the FMPC software in the dedicated PC.
3
NOTE:
In the “Procedure Selection (A-001)” screen, select “Re-installation”, then click the [Next] button.
Before the installation, check if the ROM version is displayed in the operation panel in LP.
1
Insert the FMPC installer CD into the CD drive.
In case of updating from Ver.1.0 to Ver.2.0, select "User Versionup". NMP012
2
4
The FMPC installer program is automatically started up. If the installer program is not started up, perform the following procedures.
In the “Starting Re-installation (A-100)” dialog, click the [Yes] button.
(1) Move to [EZ171] folder in the CD drive. (2) Double-click [setup.exe].
5
92
In the “Information (A-110)” dialog, click the [OK] button.
distributed by www.minilablaser.com
FMPC
6
On the “Printer Selection” screen, select “LP1500/LP2000”, then click the [Next] button.
10
11
7
8
In the “Inserting Printer’s Backup FD (A-130)” dialog, click the [Yes] button.
The “Information” dialog appears.
Installation is started.
12
Insert the Printer’s Backup FD for LP into the FD drive of the FMPC PC.
In the “FD Confirmation (A-117)” dialog, click the [Yes] button.
NMP014
13
NOTE:
Click the [OK] button.
In this case, select [NO] because the FMPC backup FD is not prepared yet.
9
In the “Inserting Backup FD (A-120)” dialog, click the [No] button.
Click.
NOTE: In this case, select [NO] because the FMPC backup FD is not prepared yet.
93
distributed by www.minilablaser.com
FMPC
14
On the “Input Source Selection [A-135]” screen, select [SP1500/SP2000], then click the [Next] button.
17
In the “Setup Completion (A-150)” dialog, click the [OK] button.
IMPORTANT Do not restart the printer (LP). If it is restarted, all parameters are initialized.
15
18
Remove the FD from the FD drive.
NMP015
16
94
In the “Re-installation Completion(A-140)” dialog, click the [OK] button.
Proceed to “4.15 DI Print/Data Writing Software Installation in FMPC”.
distributed by www.minilablaser.com
FMPC
4.15
DI Print/Data Writing Software [C4/C5] Client Installation in FMPC
Install the DI Print/Data Writing [C4/C5] Client.
1
3
On the “Start Copying Files” screen, click the [Next] button.
Replace the FMPC installer CD with the C4/C5 installer CD.
NMP012
2
4
5
Installation is started.
Browse [Start] - [Shut Down], then select [Restart] to restart the PC.
After the PC is restarted, the C4/C5 installer screen appears. Click the [Next] button.
6
On the “...Wizard Complete” screen, select “Yes, I want to...”, then click the [Finish] button.
95
distributed by www.minilablaser.com
FMPC
7
Remove the C4/C5 installer CD from the CD drive.
8
On the “Install Shield Wizard Complete” screen, select “Yes, I will restart...”, then click the [Finish] button. After the FMPC is restarted, the LP parameter downloading message I-2305 appears.
NMP013
4.16
1 2
Installation Information Setup for FMPC
Open the "4 Setup and Maintenance" screen with “SE2” (Password : 7777). Select “1) System Condition Setup and Check” - “2) Installation Information Setup”, then set up the “Delivery Date” and “Setup Date”, and then click the [OK] button.
NOTE: If the settings are changed, restarting of SP is required to activate the new settings. For the delivery and setup dates of printer, check “41F Installation Information Setup” in the scanner (SP).
96
distributed by www.minilablaser.com
SP
4.17
1
Output Device Setup for SP and Restarting SP
Restart the SP(Scanner), then open "Setup and Maintenance" - "System Condition Setup and Check" - "Installation Information Setup", and select "FMP Controller" as Output Device, then click the [OK] button.
2
Select [350] or [370] for "System Name".(This selection is not required in case of SP-3000.) Default: 370
3
Restart the SP.
NOTE: If the settings are changed, restarting of SP is required to activate the new settings. To check the delivery and setup dates of printer, select “ON” in “Output Device”.
97
distributed by www.minilablaser.com
SP
4.18
Copying Print Size Table to FD then Copying LP1500/2000 Print Size Table to FMPC
Copy the print size table from the SP to the FD by using the dedicated print size setting tool. Then, copying it to the FMPC.
(2) Copy Table from FD to FMPC
1
(1) Copy Table to FD
1 2
Insert the print size setting tool FD into the FD drive of SP1500/2000, open the Explorer, then execute “PrintsizeSetTool.exe” in FD. When the FRONTIER model and System [A1] is proper, the following message appears. Click the [OK] button to start copying it to the system.
3
Copying the data from SP to FD is started.
4
After copying, the following message appears.
2
3 4
98
FMPC
Insert the print size setting tool FD into the FD drive of FMPC, open the “Explorer”, then doubleclick “PrintSizeSetTool.exe” in FD drive. When the connections are properly done, the following message appears. To start copying, click the [OK] button.
Another confirmation message appears. Click the [OK] button to start copying.
Data is copied from the FD to the FMPC. When copying is completed, the following message appears.
distributed by www.minilablaser.com
IC
4.19
FMPC
FMPC Output Device Setting in Imaging Controller
See “3.20 FMPC Output Device Setting in Imaging Controller”.
4.20
Enabling of “Rack Auto Cleaning”
When the installation process is completed, return “Rack Auto Cleaning” to “Yes” in “[46B] Processor Operating Condition Setup” in FMPC.
4.21
Paper Condition Setup
Set up the paper condition in the FMPC.
99
distributed by www.minilablaser.com
SP
4.22
FMPC
Creating Backup FD for FMPC, SP1500/2000 and LP1500/2000
3
Back up the data both in the FMPC and FRONTIER. The following procedures are those used for the FMPC. Also, perform the same procedures for the FRONTIER.
4
Move the cursor to the “Destination” box and select “MP Controller” or “Printer” Click [OK]
• “Making the backup of the data” message appears.
[Selection] “4 Setup and Maintenance” - “1 System Operation Setup and Check” - “7 Data Backup”
[Procedure] Make a backup of unit data stored in the hard disk of the main control unit after changing the “Setup and Maintenance” data in case unit data is damaged.
1
5
Prepare the data backup floppy disk “FMPC” or “LP1500/LP2000”
• Operation returns to the “4 Setup and Maintenance” screen.
6
2
Insert the disk into the floppy drive of the main control unit.
NMP014
100
Upon completion of the backup, press the [Cancel] button.
Remove the FD from the drive.
NMP015
distributed by www.minilablaser.com
IC
4.23
SP
FMPC
Operational Check
Perform the operational check. (See 2.21 Operational Check .) For the procedures of film scanning in FRONTIER 350/370, see “5.1.2 Printing from FRONTIER (135-size film example)” in the Instruction Manual.
4.24
System Shutdown
Shut down the SP1500/2000, FMPC, then Imaging Controller in this order. This completes the FMPC installation and setup.
101
distributed by www.minilablaser.com
5 5.1
1
2
Maintenance Menu (FRONTIER 350/370/355/375) Operational Procedure • The “Setup and Maintenance” screen appears.
Select “4 Setup and Maintenance” from the main menu.
3 Select “SE2” for the user name and enter “7777” for the password, and click the [OK] button.
Select the desired item from the item list and press its [+] button. • The sub-item list appears.
• “SE1” user name is prepared for the user who manages printing quality. The password is “6666”. • “SE2” user name is prepared for the service engineer.
4
Move the cursor to the desired item and press the [START] button. • Each screen appears.
5 6
Perform operations by following the instructions on the screen. Upon completion of the setup and maintenance operations, press the [OK] button to perform processing or [Cancel] to quit the screen. • Operation returns to the “Setup and Maintenance” screen.
102
7
Click the [END] .
8
Operation returns to the main menu.
distributed by www.minilablaser.com
F350/370/355/375
5.2
System Operation Setup and Check (41)
5.2.1 Production Information 1 (411)
2
To save the data in FD, click [FD Save].
[Selection]
3
Insert the blank FD into the drive.
“4 Setup and Maintenance” - “1 System Operation Setup and Check”. - “1 Production Information 1”.
4
In the confirmation dialog box, click [OK].
[Procedure]
5
The information can be changed by selecting “Negative”, “Reversal”, “Digital Image” or “All” from the “Input Type” box.
6
After the data is saved, remove the FD from the drive. Click [OK]. • Operation returns to the “4 Setup and Maintenance” screen.
7
Select the “END [1]” on the menu bar. • Operation returns to the “Main Menu” screen. This menu is convenient for saving the data in the FD periodically.
1
To clear the data, follow the steps below.
(1) Click [Clear]. • The “Clear production information?” dialog box appears.
(2) Click [OK]. • The production data is erased.
103
distributed by www.minilablaser.com
F350/370/355/375
5.2.2 Production Information 2 (412)
(3) Click [OK]. • The data is cleared and date of clearance appears.
[Selection] “4 Setup and Maintenance” - “1 System Operation Setup and Check” - “2 Production Information 2”
[Procedure] This menu is to view acumulative amount number of production. Confirm the production information for each input type. The data can be cleared on this menu. Input Type : Color Negative Reversal Black & White Negative
1
Record the production information.
2
To clear the data, follow the steps below.
(1) Use “Input Type” to choose which data you wish to clear. (2) Then press click [Clear]. • The “Clear production information?” dialog box appears.
104
3
To save the data in FD, click [FD Save].
4
Insert the blank FD into the drive.
5
In the confirmation dialog box, click [OK].
6 7
After the data is saved, remove the FD from the drive. Click [OK].
• Operation returns to the “4 Setup and Maintenance” screen.
distributed by www.minilablaser.com
F350/370/355/375
5.2.3 Accumulated Production Information (413)
(2) Insert the formatted floppy disk into the floppy disk drive of the main control unit.
This procedure displays the production information. The data can be cleared on this menu.
[Selection] “4 Setup and Maintenance” − “1 System Operation Setup and Check” − “3 Accumulated Production Information” NMP014
(3) Click the [OK] button. • The data is saved into the floppy disk.
1
Select Negative, Reversal, Digital Image or All from the Input Type box.
(4) Remove the floppy disk from the floppy disk drive.
• The information of the input type is displayed.
2 3
Record the accumulated production information. To save the data to a floppy disk, perform the following steps.
(1) Click the [FD Save] button.
NMP015
5) Click the [OK] button. • The dialog box disappears.
4
Click the [OK] button. • Operation returns to the menu screen.
105
distributed by www.minilablaser.com
F350/370/355/375
5.2.4 Timer Setup (414)
Night-time preheating is usually conducted when the room temperature drops below 10?C (50?F) at night and the temprature is not controlled for 8 or more hours.
[Selection] “4 Setup and Maintenance” - “1 System Operation Setup and Check” - “4 Timer Setup”
(1) Select “YES” for “Preheat Setting”.
[Procedure]
• The 1st and 2nd preheat setting boxes appear.
The present date/time, timer ON date/time and preheat setup times are setup.
1
(2) Move the cursor to “1st Preheat” and enter the time. To update “Present Date/Time”, change the date and time, and click [OK].
(3) Move the cursor to “2nd Preheat” and enter the time.
To cancel the update, press the [Cancel] button.
2 3
Setup the preheat timer by following steps in the next column, if necessary. IMPORTANT The ON time for a night-time preheating operation must not overlap with the ON time of the weekly timer since night-time preheating takes priority and shuts down all power when it is set OFF. If, for instance, the calendar timer is set to 5:00 and night-time preheating is turned ON at 3:30, all the power will be shut down two hours later at 5:30.
106
• For preheating once only, set the same time for both the first and second times. • Select “NO” when no the preheat timer is used. • The second preheating timer is ignored if the first and second times overlap.
To change the timer date and time, check the day of the week and enter the time in the “Timer ON Date/Time Setting” box.
1st. preheat time: 2:00 2nd. preheat time: 3:00 With the above settings, night-time preheating will occur from 2:00 to 4:00 (2 hours).
4
Click [OK]. • Operation returns to the “4 Setup and Maintenance” screen.
distributed by www.minilablaser.com
F350/370/355/375
5.2.5 Error Information Check (415)
3
• Accumulated error information is displayed in order of code and frequency.
[Selection] “4 Setup and Maintenance” - “1 System Operation Setup and Check” - “5 Error Information Check”
• Operation returns to the “Error log information” screen.
The system error log is listed up in order of date and time.
1
Click [Accum. Info].
5
Click [OK]. • Operation returns to the “4 Setup and Maintenance” screen.
Click [OK].
• The log file is relorded.
107
distributed by www.minilablaser.com
F350/370/355/375
5.2.6 Installation Information Confirmation (416)
5.2.7 Data Backup (417) [Selection]
[Selection] “4 Setup and Maintenance” - “1 System Operation Setup and Check” - “6 Installation Information Confirmation”
[Procedure] Check the scanner and printer installation information.
1
Check the installation information.
2
Click [Option].
3
4
“4 Setup and Maintenance” - “1 System Operation Setup and Check” - “7 Data Backup”
[Procedure] Make a backup of the unit data stored in the hard disk of the main control unit after changing the “Setup and Maintenance” mode data in case unit data is damaged.
Check the version of Frontier Manager, then click [OK].
1 Click [OK] • Operation returns to the “4 Setup and Maintenance” screen.
2
Prepare the data backup floppy disk “FMPC” or “LP1500/LP2000”. Insert the disk into the floppy drive of the main control unit.
NMP014
3 4
108
Move the cursor to the “Destination” box and select “FMP Controller” or “Printer”. Click [OK].
distributed by www.minilablaser.com
F350/370/355/375
5.2.8 Clear Error Log (41E)
• “Making the backup of the data” message appears.
[Selection] Select “4 Setup and Maintenance” - “1 System Operation Setup and Check” - “E Clear Error Log”. .
[Procedure]
5
Clear unwanted system and printer error information. Upon completion of the backup, press the [Cancel] button. • Operation returns to the “4 Setup and Maintenance” screen.
6
Remove the FD from the drive.
1 2
Select the item to be cleared and press the [Clear] button. In the confirmation dialog, click the [OK] button. • The selected information is cleared.
NMP015
3
Click the [OK] button. • Operation returns to the “Setup and Maintenance” screen.
109
distributed by www.minilablaser.com
F350/370/355/375
5.2.9 Installation Information Setup (41F)
5.2.10 DI Manager Administrative Setting (41l)
[Selection]
Set the time to delete the order that is completed on the DI Controller.
Select “4 Setup and Maintenance”-“1 System Operation Setup and Check”-“F Installation Information Setup”.
[Procedure] Set the installation information for printer.
[Selection] “4 Setup and Maintenance” - “1 System Operation Setup and Check” - “I DI Manager Administrative Setting”.
[Procedure]
1 2
Select the time to delete the order that is to be done on the DI Controller. Click [OK]. • Operation returns to the “4 Setup and Maintenance” screen.
110
distributed by www.minilablaser.com
F350/370/355/375
5.3
Print Condition Setup and Check (42)
5.3.1 Paper Condition Setup
• After about 5 minutes, an upkeep print is delivered to the large-size tray.
When new paper is to be loaded, follow the procedure described below to set up the new paper condition.
Densitometer AD100:
[Selection] “4 Setup and Maintenance” - “2 Print Condition Setup and Check” - “1 Paper Condition Setup”.
[Procedure]
1
Densitometer AD200:
Select the [Magazine Upper] or [Magazine Lower] to be set up.
3
2
After the condition setup print has come out, press the [Dens Measure] button.
Click [Print].
4
Adjust the guide of the densitometer according to the width of the condition setup print.
Densitometer Operation Panel: Indicator Light
Ready Measuring
Error
Power (Green) On
On
On
Ready (Green) On
Blinks
Off
Off
On
Error (Red)
Off
When an error occurs, press the orange [RESET] switch.
111
distributed by www.minilablaser.com
F350/370/355/375
5
• The measurement is automatically started and the density measurement result is displayed.
Insert the condition setup print into the densitometer. Densitometer
7
Click [OK]. • The density measurement result disappears.
Upkeep Print EZ635
6
If the “Density Measurement Result” is NG, the message below appears. Perform Steps 5 to 10 again until the result becomes OK.
Press the [START] button on the densitometer.
8
Click [Cancel].
[START] Button EZ636
If the message below appears, click [OK] and repeat the density measurement from Step 6 .
• The “4 Setup and Maintenance” screen appears.
9
Select the “END [1]” on the menu bar. • Control returns to the “Main Menu”.
112
distributed by www.minilablaser.com
F350/370/355/375
5.3.2 Processing Solution Temperature Check
5.3.3 Control Strip Processing
“4 Setup and Maintenance” - “2 Print Condition Setup and Check” - “2 Processor Temperature”.
The processing solution performance is evaluated by processing a control strip, measuring the processed strip densities, and comparing them with the reference strip densities.
[Procedure]
■ Control Strip Preparation
[Selection]
1
Click [OK].
1
Take the control strip package out of the freezer, and leave it for about one hour to bring it to room temperature.
EZ1841
2 • Operation returns to the “4 Setup and Maintenance” screen.
2
Take the inner bag out of the control strip package and place it on the control strip holder, with its seamed surface up, and put them both in the dark box. Close the dark box cover. Seamed Surface
Control Strip Inner Bag
Select the “END [1]” on the menu bar. • Control returns to the “Main Menu” screen.
Control Strip Holder EZ740
113
distributed by www.minilablaser.com
F350/370/355/375
3
• The message “Processing the control strip.” appears.
Pass your hands through the sleeves of the dark box, take one control strip out of the inner bag, and insert it into the control strip holder, as shown in the figure. Push it in until it reaches the far end. Emulsion Surface Upward
• The message “Set Holder” appears on the operating panel on the printer.
Control Strip
4
EZ741
2
Fold over the open end of the inner bag to prevent fogging of the unused control strips.
5
Take the control strip holder out of the dark box.
6
Return the control strip package to the freezer.
Open the cover of the control strip holder port in the processor cover, and position the holder so that its “EMULSION SURFACE” mark faces the processor side. Control Strip Holder Port Cover
Control Strip Holder
■ Control Strip Processing [Selection] “4 Setup and Maintenance” - “2 Print Condition Setup and Check” - “3 Control Strip Processing”.
Processor Cover
[Procedure]
“EMULSION SURFACE” Mark EZ742
1
Click [OK] to start the control strip processing.
3
Press the [ENTER] key on the operating panel of the printer.
7.7
EZ625
114
distributed by www.minilablaser.com
F350/370/355/375
• The processor starts and control strip processing begins.
■ Control Strip Storage and Handling Precautions
• After about 4 minutes, the control strip is fed out to the large size tray.
REFRENCE: A control strip is used for checking the performance of the processing solutions. The package contents are composed of exposed but unprocessed paper strips, one reference strip (processed and used as the density reference), and the correction factor chart for the reference strip. Process a control strip once a day, measure the reflection densities (R,G,B) using a densitometer and check for processing solution performance.
• The message “Control strip processing is completed.” appears on the screen.
4 5
Remove the control strip holder from the port in the processor cover. Click [OK]. • The message is cleared.
6
Click [Cancel].
IMPORTANT • Place the control strips inside a plastic bag and store them in a freezer (-10°C/14°F or below). Storage at room temperatures leads to deterioration in performance. • Moisture condensation occurs if the control strips are processed immediately after they have been taken out of freezer. This may give rise to uneven development. • Do not open the folded end of the inner bag under any light, or the control strips may become fogged and rendered useless.
• Control returns to the “4 Setup and Maintenance” screen. For the daily morning pre-operational checks, operation returns to the “Printing Condition Upkeep”.
7
Select the “END [1]” on the menu bar. • Control returns to the “Main Menu” screen.
115
distributed by www.minilablaser.com
F350/370/355/375
5.3.4 Print Size Setup (424)
No. 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34
[Selection] “4 Setup and Maintenance” - “2 Print Condition Setup and Check” - “4 Print Size Setup”
[Procedure] Set the print size to be used. • Normally, the size is registered as shown in the table.
Name Width [0.1mm] Length [0.1mm] Display 10R 2540 3050 OFF 10RW 2540 3810 OFF 3DSC 890 1190 OFF 3DSCf 890 1270 OFF 4DSC 1020 1360 OFF 4DSCf 1020 1520 OFF 5DSC 1270 1690 OFF 5DSCf 1270 1780 OFF 89Ix 890 1200 OFF CDIDX 1020 1200 OFF 127Ix 1270 1200 OFF 3.5x7 890 1780 OFF 4x5 1020 1270 OFF 4x8.5 1020 2160 OFF 4x8 1020 2030 OFF
• If you select “ON”, the description appears on the list. If you select “OFF”, nothing appears on the list. IMPORTANT Make sure to register the sizes for index printing.
NOTE: Make sure that the size names in the FMPC are the same as in the FRONTIER.
NOTE:
1
Select the print size to be modified or registered from the list. • ID [No.], Name, Width, Length, Border, four BD values and [Display(ON/OFF)] are displayed.
2
Move the cursor to the print size to be used, select “ON” or “OFF” shown in the “Display”.
Width [0.1mm] Length [0.1mm] Display 890 1270 ON 890 2540 ON 890 1580 ON 1020 1520 ON 1020 2540 ON 1020 1780 ON 1270 890 ON 1270 890 OFF 1270 1780 OFF 1270 1780 OFF 1520 1020 OM 1520 1020 OFF 1520 2030 OFF 1520 2160 OFF 2030 2540 ON 2030 3050 OFF 2100 1480 OFF 2100 2970 OFF 2540 2030 OFF
Click [OK] • Operation returns to the “4 Setup and Maintenance” screen.
distributed by www.minilablaser.com
F350/370/355/375
5.3.5 Paper Condition Method Setup (42J) [Selection] Select “4 Setup and Maintenance”- “2 Print Condition Setup and Check ”- “J Paper Condition Method Setup”.
[Procedure] Set the paper condition setup type.
5.3.6 Back Print Setup (42O) IMPORTANT This setting is available only for the DSC printing. For the film printing, perform the “Back Print Setup (42O)” in the scanner (SP).
[Selection] Select “4 Setup and Maintenance”-“2 Print Condition Setup and Check”-“O Back Print Setup”.
[Procedure]
1 2 3 4
1
Select “NO” or “YES” for “Back Print”.
2
Click the [OK] button.
Select “YES” or “NO” for the “Ambient variable” correction . Select “YES” or “NO” for the “Master magazine” registration . If “YES” is selected for Step “2”, set the ID, width, paper and type for the master magazine.
• Operation returns to the “Setup and Maintenance” screen.
Click the [OK] button. • Operation returns to the “Setup and Maintenance” screen.
117
distributed by www.minilablaser.com
F350/370/355/375
5.4
Printer Adjustment/Maintenance (45)
5.4.1 Paper Magazine Registration (451)
2
Remove the two screws and adjust the paper guide width in accordance with the paper width.
[Selection] “4 Setup and Maintenance” - “5 Printer Adjustment/ Maintenance” - “1 Paper Magazine Registration”
[Procedure] Register the Paper Magazine to be used.
Screws (2) Paper Guide EZ854
Do not loosen the red-painted screws.
3 1
Remove the two screws and adjust the flange width in accordance with the paper width. Paper Shaft
Open the paper magazine by releasing the latch. Screws (2)
Flange EZ855
Latch EZ643
118
distributed by www.minilablaser.com
F350/370/355/375
4
Select a paper ID referring to the table below, and enter the data. Magazine Paper Width ID (mm) 1 89 2 102 3 117 4 127 5 152 6 89 7 102 8 117 9 127 10 152 11 203 12 210 13 254 14 203 15 152 16 254 18 254
Install the ID chip on the paper magazine with the two screws.
Screws (2) EZ1218
7
Click [OK]
To register paper not listed in the table, use an unused magazine ID.
5
Click [Set].
• Operation returns to the “4 Setup and Maintenance” screen.
119
distributed by www.minilablaser.com
F350/370/355/375
5.4.2 Paper Feed Length Adjustment (452)
6
Add the increment to the value in “Fine adjust value” and enter it in the “Fine adjust value” box.
Fine adjust value = 1.0mm Increment = 0.4mm New Fine Adjust Value = 1.0 + 0.4 = 1.4
[Selection] Select “4 Setup and Maintenance”-“5 Printer Adjustment/Maintenance”-“2 Paper Feed Length Adjustment”.
[Procedure]
7
With Menu “453 Test Pattern Printing”, make a print with a 127.0mm feed length.
Adjust the paper feed length.
8
Measure the feed length of the print fed out and calculate the offset increment using the formula below.
Offset Increment = 127–Measured Value of 127mm Measured Value of 127mm =126.6mm Offset Increment Value = 127–126.6 = 0.4mm
1 2 3 4 5
Select the ID number of the magazine to be adjusted from the list on the screen and click it. Make sure the value in the “Set value (feed length)” is “254.0”. Enter the fine adjustment feed length value indicated on the label attached to the magazine in the “Fine adjust value” box. On Menu “453 Test Pattern Printing”, make two prints with 127mm and 381mm feed lengths. Measure the feed lengths of the prints fed out and calculate the increment using the formula below.
Increment = 254 – (Measured Value of 381mm – Measured Value of 127mm) Measured Value of 381mm = 380.0mm Measured Value of 127mm = 126.4mm Increment = 254 – (380 – 126.4) = 0.4
120
9
Add the offset increment to the value in “Offset value” and enter it in the “Offset value” box.
10
Repeat Steps 1 to 9 for all paper magazines.
11
Click [OK].
• Operation returns to the “4 Setup and Maintenance” screen
distributed by www.minilablaser.com
F350/370/355/375
5.4.3 Test Pattern Printing (453)
Bordered contact
[Selection] Select “4 Setup and Maintenance” - “5 Printer Adjustment/Maintenance”- “3 Test Pattern Printing”.
[Procedure] Create the test pattern prints.
Gradation
1
Step wedge
Move the cursor to the “Test pattern selection”, and select “Grid”, “Borderless contact”, “Bordered contact”, “Gradation” or “Step wedge”.
Grid
Borderless contact
121
distributed by www.minilablaser.com
F350/370/355/375
2 3
Move the cursor to the “Feed length” and enter “254” (mm).
5.4.4 G, B Laser (SHG) Optimal Temperature Setup (454)
Click the [Print] button.
[Selection]
• The message “Printing the test pattern print” appears.
“4 Setup and Maintenance” - “5 Printer Adjustment/ Maintenance” - “4 G, B Laser (SHG) Optimal Temperature Setup”
• After about 5 minutes, the print is output to the large size tray.
[Procedure] Setup the G, B laser (SHG) optimal temperature.
4
5
Move the cursor to the “Magazine”, select another magazine and press the [Print] button.
NOTE:
Perform test pattern prints for all the magazines to be used.
Perform this menu two hours after the LD has been ON. This provides sufficient time for the laser to warm up.
Use the magnifying lens (X25) to check that the vertical lines for judging the color skew are within 1/8 pixel width, and the horizontal lines within 1/4 pixel width.
1
Click [Enter].
REFERENCE: 1 pixel width = 0.08mm
6
Click the [End] button. • Operation returns to the “Setup and Maintenance” screen.
• The optimal temperature setup is started, and the result is displayed after 5 minutes.
2
Click [End].
• Operation returns to the “4 Setup and Maintenance” screen.
122
distributed by www.minilablaser.com
F350/370/355/375
5.4.5 Paper Feed (455)
5.4.6 Printer Temperature Display (456)
[Selection]
[Selection]
“4 Setup and Maintenance” - “5 Printer Adjustment/ Maintenance” - “5 Paper Feed”
“4 Setup and Maintenance” - “5 Printer Adjustment/ Maintenance” - “6 Printer Temperature Display”
[Procedure]
[Procedure]
Paper is fed without printing.
Printer temperature and its status are displayed.
1
Set the number of prints, feed length and select magazine. Quantity : 1 to 999 Feed Lengh : 82.5 to 381.0
2
Click [OK].
NOTE: The temperatures are updated every 5 seconds. Keep the “Abnormal temp. detection” to “ON”.
1
Click [OK].
• Operation returns to the “4 Setup and Maintenance” screen.
• Paper is fed.
3
Click [End]. • Operation returns to the “4 Setup and Maintenance” screen.
[Selection] “4 Setup and Maintenance” - “5 Printer Adjustment/ Maintenance” - “8 Image Position Fine Adjustment”
[Procedure] Check the status of the sensors.
1
Click [End].
• Operation returns to the “4 Setup and Maintenance” screen.
[Procedure] Adjustment of the image position for each paper magazine.
1 2
Make a bordered print to be adjusted. Select the paper magazine for print to be adjusted.
3
Check that the image is in the center of paper.
4
If necessary, adjust by following the steps below.
(1) On Menu 424 “Print Size Setup”, enter initial bordered width (4.0mm or 5.0mm) in “Upper BD”, “Lower BD”, “Left BD” and “Right BD” columns (see Subsection 9.3.4). (2) To move the image in the feed direction, decrease the value in the “Sub-scanning”. (3) To move the image in the reverse direction, increase the value in the “Sub-scanning”. (4) To move the image in the rear direction, decrease the value in the “Main scanning”. (5) To move the image in the front direction, increase the value in the “Main scanning”.
• Operation returns to the “4 Setup and Maintenance” screen.
[Procedure] Check the operation of the motors and solenoids, and status of the sensors.
The distribution section moves to the following position by choosing the button. [Waiting] : Waiting position [Rise] : Distribution position [Decent] : Absorption position
125
distributed by www.minilablaser.com
F350/370/355/375
5.4.10 Printer Function Select (45B) [Selection] Select “4 Setup and Maintenance” -“5 Printer Adjustment/Maintenance ”- “B Printer Function Select”.
[Procedure] Set the distribution function.
1
Click any buttons of the operation commands. • The selected operation is driven.
2
Click the [Cancel] button. • Operation returns to the “Setup and Maintenance” screen.
1
Select “YES” or “NO” for “Distribution”.
2
Click [OK]. • Operation returns to the “4 Setup and Maintenance” screen.
Select “4 Setup and Maintenance” - “5 Printer Adjustment/Maintenance” - “D R Laser(R-LD) Data”.
[Procedure]
[Procedure]
Perform the RGB test exposure and check the operation.
Display the R laser (R-LD) data on the EEPROM.
1
1
Click the [OK] button.
Click the [OK] button. • Operation returns to the “Setup and Maintenance” screen.
• Operation returns to the “Setup and Maintenance” screen.
127
distributed by www.minilablaser.com
F350/370/355/375
5.4.13 G Laser (G-SHG) Data (45E)
5.4.14 B Laser (B-SHG) Data (45F)
[Selection]
[Selection]
Select “4 Setup and Maintenance” - “5 Printer Adjustment/Maintenance” - “E G Laser (G-SHG) Data”.
Select “4 Setup and Maintenance” - “5 Printer Adjustment/Maintenance” - “F B Laser (B-SHG) Data”.
[Procedure]
[Procedure]
Display the G laser (G-SHG) data on the EEPROM.
Display the B laser (B-SHG) data on the EEPROM.
1
Click the [OK] button. • Operation returns to the “Setup and Maintenance” screen.
128
1
Click the [OK] button. • Operation returns to the “Setup and Maintenance” screen.
distributed by www.minilablaser.com
F350/370/355/375
5.4.15 Scanning Position/Scanning Home Position Parameter Setup (45G)
5.4.16 Main Scanning Position Adjustment/Laser Beam Sync. Rough Adjustment (45H)
[Selection] Select “4 Setup and Maintenance” - “5 Printer Adjustment/Maintenance” - “G Scanning Position/ Scanning Home Position Parameter Setup”.
[Procedure]
[Selection] Select “4 Setup and Maintenance” - “5 Printer Adjustment/Maintenance” - “H Main Scanning Position Adjustment/Laser Beam Sync. Rough Adjustment”.
Display the parameters for exposure positions.
[Procedure] Perform the scanning adjustment and laser beam synchronization rough adjustment.
1
Click the [OK] button. • Operation returns to the “Setup and Maintenance” screen.
1
Click the [OK] button.
129
distributed by www.minilablaser.com
F350/370/355/375
• After about 5 minutes, the print is output to the large size tray.
9
Find the best Y coordinate which has the least color skew on the output print for the horizontal lines using the magnifier (x20-40), and enter the coordinate value and drifted color (CMY) order from the top.
C
A
10
B Sub-scanning (Horizontal) Line
11 12
Main Scanning (Vertical) Line
13
Move the cursor to the “X(Width)” and enter the measured “X” value Move the cursor to the “Y(Width)” and enter the measured “Y” value. Press the [Enter] button of the “Coordinate” with least amount of color drift . Click the [End] button.
• Operation returns to the “Setup and Maintenance” screen.
Laser Beam Synchronizing Adjustment Block
2
Measure A, B and C shown on the screen and record each value.
Accuracy: 0.5mm
3 4 5 6 7 8
130
Move the cursor to the “A: Left measured value” and enter “A” value. Move the cursor to the “B: Right measured value” and enter “B” value. Press the [Enter] button. Move the cursor to the “C: Top measured value” and enter “C” value. Click the [Enter] button. Find the best X coordinate which has the least color skew on the output print for the vertical lines using the magnifier (x20-40), and enter the coordinate value and the drifted color (CMY) order from the left-hand side.
distributed by www.minilablaser.com
F350/370/355/375
5.4.17 Laser Beam Sync. Fine Adjustment Print (45J)
• The print is output to the large-size tray.
[Selection] Select “4 Setup and Maintence”-“5 Printer Adjustment/Maintenance”-“J Laser Beam Sync. Fine Adjustment Print”.
[Procedure] Perform the fine adjustment of the laser beam synchronization.
1
2
3
Move the cursor to the “Order of drifted colors for main scanning” and enter the measured X value measured in “Main Scanning Position Adjustment/Laser Beam Sync. Rough Adjustment (Menu 45H)”. Move the cursor to the “Order of drifted colors for sub-scanning” and enter the measured Y value measured in “Main Scanning Position Adjustment/Laser Beam Sync. Rough Adjustment (Menu 45H)”.
4
5 6 7
Find the best XY coordinate which has the least color skew on the output print for the horizontal lines using the magnifier (x20-40), and enter its number. Move the cursor to the “Best main scanning position” and enter its number. Move the cursor to the “Best sub-scanning position” and enter its number. Click the [OK] button.
Click the [Print] button. • Operation returns to the “Setup and Maintenance” screen.
131
distributed by www.minilablaser.com
F350/370/355/375
5.4.18 Laser History Display (45K)
5.4.19 Paper Condition Setup Table (LUT) Copy (45L)
[Selection] Select “4 Setup and Maintence”-“5 Printer Adjustment/Maintenance”-“K Laser History Display”.
[Selection] Select “4 Setup and Maintence”-“5 Printer Adjustment/Maintenance”-“L Paper Condition Setup Table (LUT) Copy”.
[Procedure] Display the exposure time and current value of RLD, G-SHG and B-SHG.
1
Click the [Switch display] to switch between the graph and numeric displays.
[Procedure] Copy the LUT (Look-up Table) between magazines.
1
Specify the ID of the source magazine.
2
Specify the ID of the destination magazine.
3
Click the [OK] button. • The copy is performed and operation returns to the “Setup and Maintenance” screen.
2
Click the [OK] button. • Operation returns to the “Setup and Maintenance” screen.
132
distributed by www.minilablaser.com
F350/370/355/375
5.4.20 Printer Mechanism Fine Adjustment (45M)
2
[Selection]
Enter the adjustment values indicated on the labels attached to the distribution unit for the Distribution section boxes. 2-line Front
Select “4 Setup and Maintence”-“5 Printer Adjustment/Maintenance”-“M Printer Mechanism Fine Adjustment”.
3-line Front
3-line Rear
2-line Rear
[Procedure] Perform fine adjustment of the width guide, distribution section and the sub-scanning motor speed.
Bottom EZ1599
Enter the “Front Up/Down Section Adjustment” value in the “Top” box.
3
Click the [OK] button. • Operation returns to the “Setup and Maintenance” screen.
Width guide : mm Bottom : pulse 2-line rear : pulse 2-line front : pulse Top : pulse 3-line rear : pulse 3-line front : pulse Subscan motor speed: 0.1%
1
Refer to the “Paper Width Guide Adjustment” for Width guide.
133
distributed by www.minilablaser.com
F350/370/355/375
5.4.21 Back Printer Test (45N)
5.4.22 Printer Operation Data Display (45P)
[Selection] Select “4 Setup and Maintence”-“5 Printer Adjustment/Maintenance”-“N Back Printer Test”.
[Procedure]
[Selection] Select “4 Setup and Maintenance”- “5 Printer Adjustment/Maintenance” - “P Printer Operation Data Display”.
Perform the test print of the back printer.
[Procedure] Check printer operation data.
1
Set the “Q’ty” and “Feed length”.
2
Select the magazine to be used. • The test print is output to the large-size tray.
3
Click the [Cancel] button. • Operation returns to the “Setup and Maintenance” screen.
134
1
Click the [OK] button. • Operation returns to the “Setup and Maintenance” screen.
distributed by www.minilablaser.com
F350/370/355/375
5.4.23 Data Saving (45T)
5.4.24 Data Download (45U)
[Selection]
[Selection]
Select “4 Setup and Maintence”-“5 Printer Adjustment/Maintenance”-“T Data Saving”.
Select “4 Setup and Maintence”-“5 Printer Adjustment/Maintenance”-“U Data Download”.
[Procedure]
[Procedure]
Store the printer data into the hard disk of the main control unit.
Download the printer data into the printer.
1
Select item to be saved.
2
Click the [OK] button.
1
Select item to be downloaded.
2
Click the [OK] button. • Data is downloaded.
• Data is saved. • Operation returns to the “Setup and Maintenance” screen.
3
Click Press the [OK] button. • Operation returns to the “Setup and Maintenance” screen.
Click the [End] button. • Value is registered. • Operation returns to the “Setup and Maintenance” screen.
136
distributed by www.minilablaser.com
F350/370/355/375
5.5
Processor Adjustment/Maintenance (46)
5.5.1 Replenisher Pump Output Measurement
2
Remove the sub-tank cover.
If the replenisher pump output is reduced, improper processing and drop in level of solution in the processing tank may result. Processing solutions may irritate the eyes and skin. When handling processing solutions, wear protective goggles, a rubber apron, rubber gloves, rubber boots and other protective gear as appropriate to prevent any solution from coming in contact with the body. Always wash hands well after handling processing solutions.
[Selection]
Sub-tank Cover EZ679
3
Click [Start] of the “PS-R” box. • The alarm beeps intermittently for 10 seconds.
Before the pump starts discharging, disconnect the PS-R replenisher nozzle and insert it into the measuring cylinder. PS-R Replenisher Nozzle
Prepare a measuring cylinder.
Measuring Cylinder EZ747
137
distributed by www.minilablaser.com
F350/370/355/375
• The replenisher pump starts discharging after the alarm beeps for 10 seconds.
5.5.2 Auto-cleaning Pump Output Measurement
• The alarm beeps when discharging is completed.
If the auto-cleaning pump output is reduced, improper processing and drop in processing tank solution may result.
5
Insert the PS-R replenisher nozzle into the PS sub-tank.
6
Place the measuring cylinder on a level surface, then read and record the output.
7
Pour the replenisher solution from the measuring cylinder into the waste recovery tank.
8
Select the “Measured value” box for “PS-R” using the mouse or field key, and enter the recorded output value using numeric keys or the [ ↑ ] and [ ↓ ] keys. The machine automatically measures and adjusts the pump outputs for P1-R, P2-RA and P2-RB.
9
Click [OK]. • Operation returns to the “4 Setup and Maintenance” screen.
10
Processing solutions may irritate the eyes and skin. When handling processing solutions, wear protective goggles, a rubber apron, rubber gloves, rubber boots and other protective gear, as appropriate, to prevent any solution from coming in contact with the body. Always wash hands well after handling the processing solutions.
Prepare two measuring vessels to measure the auto-cleaning pump output. Remove the processor cover.
Select the “END [1]” on the menu bar.
• Control returns to the “Main Menu” screen.
11
Reinstall the sub-tank cover.
12
Clean the measuring cylinder. Processor Cover EZ685
138
distributed by www.minilablaser.com
F350/370/355/375
3
6
Remove the dryer entrance rack cover.
Drain the auto-cleaning nozzles.
Dryer Entrance Rack Cover
Auto-cleaning Nozzle EZ1071 EZ690
4
Release the lock and remove the No.1 crossover rack.
7
Install each auto-cleaning nozzle into a measuring vessel. Auto-cleaning Nozzle
Lock Release Lever
No.1 Crossover Rack
Measuring Vessel EZ1067 EZ686
5
Release the locking hook and remove the two auto-cleaning nozzles from the No.1 crossover rack.
8
Install the measuring vessels on the processing rack by aligning their rubber joints with the washing solution tank holes. Measuring Vessel
Locking hook No.1 Crossover Rack
Rubber Joint EZ1068
Auto-cleaning Nozzles (2)
EZ687
If the rubber joints are not installed properly, the replenisher solution will splash. Push in each measuring cup until its locking hook engages the rack. If it is installed improperly, the replenisher solution will splash.
139
distributed by www.minilablaser.com
F350/370/355/375
9
11
Click [Start] for “P1”.
Hold the measuring vessels upright, read both vessels, add up the total volume and record it.
Measuring Vessels EZ1070
• The alarm beeps intermittently for 10 seconds.
12 13
Click [Cancel] to stop the operation.
14 15 • The alarm beeps once when the discharging is completed.
10
Remove the measuring vessels by releasing the locks.
16
Discard the solution. Reinstall the washing nozzles into the No.1 crossover rack, and reinstall the crossover rack on the P1 processing rack. Select “Measured value” for “P1”, and enter the recorded output value using numeric keys or the [ ↑ ] and [ ↓ ] keys. Select “P2”, “PS1”, and “PS3”, and perform Steps 11 through 16 for them successively. Click [OK].
• Control returns to the “4 Setup and Maintenance” screen.
17
Select the “END [1]” on the menu bar.
Measuring Vessel
• Control returns to the “Main Menu” screen.
18
Lock Release Lever EZ1069
140
Reinstall the dryer entrance rack cover and the processor cover.
distributed by www.minilablaser.com
F350/370/355/375
5.5.3 Processing Temperature Setting (463)
5.5.4 Replenisher Rate Setup (464) [Selection]
[Selection] “4 Setup and Maintenance” - “6 Processor Adjustment/Maintenance” - “3 Processing Temperature Setting”
Select “YES” to “Evaporation Correction”, and “Standard” to “Humidity”.
1
Select “YES” to “Low volume”.
2
Enter value in the “Min. processing amount” box. Range : 0.0 to 15.0
Click [OK].
3
• Operation returns to the “4 Setup and Maintenance” screen.
Enter value in the “Min. processing amount (last 8 days)” box. Range : 0.0 to 99.9
4
To clear the data, press the [Clear] button.
5
Click [OK]. • Operation returns to the “4 Setup and Maintenance” screen.
142
distributed by www.minilablaser.com
F350/370/355/375
3
5.5.7 Processor Temperature Calibration (467)
Measure the temperature of the processing solution and record it.
[Selection] “4 Setup and Maintenance” - “6 Processor Adjustment/Maintenance” - “7 Processor Temperature Calibration”
[Procedure] Perform the processor section temperature calibrations.
EZ749
4
Reinstall the filter by aligning the fastening tab with the notch, and turn it 90° clockwise. Fastening Tab
1 2
Check that the display values reach the “Setting” temperatures.
Filter Holder
notch EZ682
Turn the P1 filter holder 90° counterclockwise, remove the P1 circulation filter and place it on the tray.
5
P1 Filter Holder
If the “Setting” temperatures differ from the values displayed, move the cursor to the “Measured value” and enter the values recorded in Step 3. Range : 0.0 to 99.9
6 7
Click [Enter]. For P2, PS2 and PS4, perform Steps 1 through 6.
Select “4 Setup and Maintenance” - “6 Processor Adjustment/Maintenance” - “C Processor Operation Data Display”.
[Procedure]
[Procedure]
Set the processor’s operating condition.
The processor operation data is displayed. This data can be cleared on Menu 46D.
1 2 3 4 5
Select “YES” or “NO” for the dryer section preheat driving. Select “YES” or “NO” for the rack auto cleaning. Select “YES” or “NO” for the auto intermittent driving. Select “YES” or “NO” for the paper feed-out switch. Click the [OK] button. • Operation returns to the “Setup and Maintenance” screen.
146
1
Click the [OK] button. • Operation returns to the “Setup and Maintenance” screen.
distributed by www.minilablaser.com
F350/370/355/375
5.5.12 Processor Operation Data Display 2 (46E) [Selection] Select “4 Setup and Maintenance” - “6 Processor Adjustment/Maintenance” - “E Processor Operation Data Display 2”.
[Procedure] The processor operation data is displayed. This data can be cleared on Menu 46D.
1
Click the [OK] button. • Operation returns to the “Setup and Maintenance” screen.
147
distributed by www.minilablaser.com
F350/370/355/375
5.6
Special Operations (48)
5.6.1 Paint (48A)
5.6.2 Explorer (48B)
[Selection]
[Selection]
Select “4 Setup and Maintence”-“8 Special Operations”-“A Paint”.
Select “4 Setup and Maintence”-“8 Special Operations”-“B Explorer”.
[Procedure]
[Procedure]
Use the “Paint”.
Use the “Explorer”.
For operations of the “Paint”, see the WindowsR XP manual.
1
Click the [X] button in the upper right-hand corner of the screen.
NOTE:
For operations of the Explorer , see the WindowsR XP manual.
1
Click the [X] button in the upper right-hand corner of the screen. Be sure not to press the emergency button.
Be sure not to press the emergency button. • Operation returns to the “Setup and Maintenance” screen.
148
• Operation returns to the “Setup and Maintenance” screen.
distributed by www.minilablaser.com
F350/370/355/375
5.6.3 Command (48C) [Selection] Select “4 Setup and Maintence”-“8 Special Operations”-“C Command”.
[Procedure] Perform the MS-DOS command operations.
For operation of the “Command”, see the MSDOS(TM) manual.
1
Click the [X] button in the upper right-hand corner of the screen. • Operation returns to the “Setup and Maintenance” screen.
149
distributed by www.minilablaser.com
6 6.1
1
Maintenance Menu (FRONTIER 570)
F570
Operational Procedure
Select “4 Setup and Maintenance” from the main menu.
3
Select the desired item from the item list and press its [+] button. • The sub-item list appears
2
Select “SE2” for the user name and enter “7777” for the password, and click the [OK] button. • “SE1” user name is prepared for the user who manages printing quality. The password is “6666”. • “SE2” user name is prepared for the service engineer.
4
Move the cursor to the desired item and press the [START] button. • Each screen appears.
5 6
Perform the operation by following the instructions on the screen. Upon completion of the setup and maintenance operations, press the [OK] button to perform processing or [Cancel] to quit the screen. • Operation returns to the “Setup and Maintenance” screen.
• The “Setup and Maintenance” screen appears.
150
7
Click the [END] .
8
Operation returns to the main menu.
distributed by www.minilablaser.com
F570
6.2
System Operation Setup and Check (1)
6.2.1 Production Information 1 (411)
2) Insert the formatted floppy disk into the floppy disk drive of the main control unit.
This procedure displays the production information. The data can be cleared on this menu.
[Selection] “4 Setup and Maintenance” - “1 System Operation Setup and Check” − “1 Production Information 1”
NMP014
3) Click the [OK] button.
1
Select Negative, Reversal, Digital Image or All from the Input Type box. • The data is saved into the floppy disk. • The information of the input type is displayed.
2 3
Record the production information.
4) Remove the floppy disk from the floppy disk drive.
To save the data to a floppy disk, perform the following steps.
1) Click the [FD Save] button.
NMP015
5) Click the [OK] button. • The dialog box disappears.
151
distributed by www.minilablaser.com
F570
4
To clear the data, perform the following steps.
1) Click the [Clear] button. • The “Clear production information?” dialog box appears. 2) Click the [OK] button.
6.2.2 Production Information 2 (412) This procedure displays the production information. The data can be cleared on this menu.
[Selection] “4 Setup and Maintenance” − “1 System Operation Setup and Check” − “2 Production Information 2”
• The data is cleared and clearing date appears.
5
Click the [OK] button.
1
Select Negative, Reversal, Digital Image or All from the Input Type box. • The information of the input type is displayed.
2 3 • Operation returns to the menu screen.
152
Record the production information. To save the data to a floppy disk, perform the following steps.
1) Click the [FD Save] button.
distributed by www.minilablaser.com
F570
2) Insert the formatted floppy disk into the floppy disk drive of the main control unit.
4
To clear the data, perform the following steps.
1) Click the [Clear] button. • The “Clear production information?” dialog box appears. 2) Click the [OK] button. • The data is cleared and clearing date appears.
NMP014
5
Click the [OK] button.
3) Click the [OK] button.
• The data is saved into the floppy disk. 4) Remove the floppy disk from the floppy disk drive.
• Operation returns to the menu screen.
NMP015
5) Click the [OK] button. • The dialog box disappears.
153
distributed by www.minilablaser.com
F570
6.2.3 Accumulated Production Information (413)
2) Insert the formatted floppy disk into the floppy disk drive of the main control unit.
This procedure displays the production information. The data can be cleared on this menu.
[Selection] “4 Setup and Maintenance” − “1 System Operation Setup and Check” − “3 Accumulated Production Information” NMP014
3) Click the [OK] button. • The data is saved into the floppy disk.
1
Select Negative, Reversal, Digital Image or All from the Input Type box.
4) Remove the floppy disk from the floppy disk drive.
• The information of the input type is displayed.
2 3
Record the accumulated production information. To save the data to a floppy disk, perform the following steps.
1) Click the [FD Save] button.
NMP015
5) Click the [OK] button. • The dialog box disappears.
4
Click the [OK] button. • Operation returns to the menu screen.
154
distributed by www.minilablaser.com
F570
6.2.4 Timer Setup (414)
Night-time preheating is usually conducted when the room temperature drops below 10°C (50°F) at night and the temperature is not controlled for 8 or more hours.
This procedure sets the present date/time, timer ON date/time and preheat setup times.
[Selection] “4 Setup and Maintenance” − “1 System Operation Setup and Check” − “4 Timer Setup”
1) Select “YES” for “Preheat Setting”. • The 1st and 2nd preheat setting boxes appear.
1
To update “Present Date/Time”, change the date and time, and click the [OK] button.
2) Move the cursor to “1st Preheat” and enter the time. 3) Move the cursor to “2nd Preheat” and enter the time.
• To cancel the update, click the [Cancel] button. • If the OS uses the 24-hour system, “04 to 09” and “14 to 19” cannot be entered directly. Use the spin buttons to enter these hours.
2
3
NOTE: • For preheating once only, set the same time for both the first and second times. • Select “NO” when the preheat timer is not used. • The second preheating timer is ignored if the first preheat time and second preheat time overlap.
To change the timer date and time, enter a checkmark, [✔] in the day of the week boxes and enter the time in the “Timer ON Date/Time Setting” box.
1st. pre-heat time: 2:00AM
Set the preheat timer by performing the following steps, if necessary. IMPORTANT The ON time for a night-time preheating operation must not overlap with the ON time of the weekly timer since night-time preheating takes priority and shuts down all power when it is set OFF. If, for instance, the calendar timer is set to 5:00AM and night-time preheating is turned ON at 3:30AM, all the power will be shut down two hours later at 5:30AM.
2nd. pre-heat time: 3:00AM With the above settings, night-time preheating will occur from 2:00AM to 4:00AM (2 hours).
4
Click the [OK] button. • Operation returns to the menu screen.
155
distributed by www.minilablaser.com
F570
6.2.5 Error Information Check (415)
3
Click the [Accum. Info.] button.
The system error log is listed up in order of date and time.
[Selection] “4 Setup and Maintenance” − “1 System Operation Setup and Check” − “5 Error Information Check”
• Accumulated error information is displayed in order of code.
4 1
Click the [OK] button.
Click the [Log Info.] button. • The “Log File Re-reading Check” dialog box appears.
2
Click the [OK] button.
• Operation returns to the menu screen.
• The log file is read out and the latest information is displayed on the screen.
156
distributed by www.minilablaser.com
F570
6.2.6 Installation Information Reference (416) This procedure displays the scanner and printer installation information.
[Selection] “4 Setup and Maintenance” − “1 System Operation Setup and Check” − “6 Installation Information Reference”
6.2.7 Data Backup (417) This procedure makes a backup of the data stored on the hard disk of the main control unit when data, indicated on the data sheet located inside the front upper cover, is changed. The backup floppy disks are used when reinstalling or reverting to earlier system software.
[Selection] “4 Setup and Maintenance” − “1 System Operation Setup and Check” − “7 Data Backup”
1
Check the installation information.
2
Click the [Option] button.
1
• The “Optional Device Reference” dialog box appears.
3
Prepare a new floppy disk for data backup when backing up data.
NOTE: A floppy disk is unnecessary for pricing unit data backup because data is backed up to the hard disk of the main control unit.
Click the [OK] button.
2 3
Insert the floppy disk into the floppy drive of the main control unit. Move the cursor to the “Destination” box and select “FMP Controller” or “Printer”.
• The dialog box disappears.
4
Click the [OK] button. • Operation returns to the menu screen.
157
distributed by www.minilablaser.com
F570
4
Click the [OK] button.
6.2.8 Clear Error Log (41E) This procedure clears the system error and printer error information.
[Selection] “4 Setup and Maintenance” − “1 System Operation Setup and Check” − “E Clear Error Log” • The “Making the backup of the data” message appears.
5
Upon completion of the backup, click the [Cancel] button. • Operation returns to the menu screen.
1
Select the item to be cleared and click the [Clear] button. • The selected information is cleared.
2
Click the [OK] button.
• Operation returns to the menu screen.
158
distributed by www.minilablaser.com
F570
6.2.9 Installation Information Setup (41F)
6.2.10 DI Manager Administrative Setting (41I)
This procedure sets the installation information. After setting up, restart the system to activate the new settings.
This menu is used when connecting the optional Imaging Controller.
[Selection] [Selection] “4 Setup and Maintenance” − “1 System Operation Setup and Check” − “F Installation Information Setup”
“4 Setup and Maintenance” − “1 System Operation Setup and Check” − “I DI Manager Administrative Setting” “Delete Waiting Time”: Sets up the time until the order processed on the Imaging Controller is deleted.
1 2
3
Set the delivery date, startup date and lab ID. Make sure that Input Device and Output Device are set as follows. Intput Device: SP-3000 (V1.7-) Output Device: LP-5700
1
Click the [OK] button. Printer (sRGB)
• Operation returns to the menu screen.
4
Set up the logical device name as follows.
Logical Device Name
Device Name
sRGBFMPC
LP-5700
Printer (F-COLOR/PD) PDFMPC
Perform the post-operational checks to shut down the system and then restart the system.
2
LP-5700
Click the [OK] button.
• The new settings are activated.
159
distributed by www.minilablaser.com
F570
6.3
Print Condition Setup and Check (2)
6.3.1 Paper Condition Setup (421)
Condition Setup Print
When new paper is to be loaded, follow this procedure to set up the new paper condition.
[Selection] “4 Setup and Maintenance” − “2 Print Condition Setup and Check” − “1 Paper Condition Setup”
3
Adjust the guide of the densitometer according to the width of the condition setup print. Densitometer
1
Guide
Install the paper magazine to be set up and select “Magazine (upper)” or “Magazine (lower)”. Click the [Initialize] button to initialize condition setup data.
2
EZ634
Click the [Print] button.
If an error occurs, press the orange [RESET] switch.
4
Insert the condition setup print into the densitometer. Densitometer [START] Button
• After about three minutes, a condition setup print is fed out.
L2997
160
distributed by www.minilablaser.com
F570
5
Click the [Dens. Measure] button.
NOTE: If the “Density Measurement Result” is not acceptable, the message shown below appears. Repeat Steps 2 to 6 until the result becomes OK.
• The measurement is started and the density measurement result is displayed.
6
Click the [OK] button.
7
Click the [Close] button. • Operation returns to the menu screen.
• The density measurement result dialog box disappears.
161
distributed by www.minilablaser.com
F570
6.3.2 Print Size Setup (424) This procedure sets the print size to be used.
[Selection] “4 Setup and Maintenance” − “2 Print Condition Setup and Check” − “4 Print Size Setup”
Select the print size to be modified or registered from the list. • ID [No.], Name, Width, Length, Border, four BD values and [Display (ON/OFF)] are displayed.
2
Move the cursor to the print size to be used, select “ON” or “OFF” shown in the “Display”. • If you select “ON”, the description appears in the list. If you select “OFF”, nothing appears in the list.
3
6.3.3 Paper Condition Method Setup (42J) This procedure sets the paper condition setup method.
[Selection] “4 Setup and Maintenance” − “2 Print Condition Setup and Check” − “J Paper Condition Method Setup”.
Click the [OK] button. • Operation returns to the menu screen.
↓ [Next page] [Prev. page] ↑
↓ [Next page] [Prev. page] ↑
163
distributed by www.minilablaser.com
F570
1 2 3
Select “YES” or “NO” for the ambient variable correction. Select “YES” or “NO” for the master magazine registration. If “YES” is selected in Step 2, set the ID, width, paper and type for the master magazine.
NOTE: • Ambient variable correction: When there is a sudden change in temperature during the day, it influences the color formation stability of color papers. To maintain constant printing quality in that condition, select “YES”. • Master magazine registration: Paper condition setup must be performed for all papers if NO is selected.
4 5
6.3.4 Back Printing Setup (42O) IMPORTANT This setting is available only for the DSC printing. For the film printing, perform the “Back Print Setup (42O)” in the scanner (SP).
[Selection] Select “4 Setup and Maintenance” − “2 Print Condition Setup and Check” − “O Back Print Setup”.
[Procedure]
1
Select “NO” or “YES” for “Back Print”.
2
Choose the [OK] button.
Click the [Next Page] button, then enter the password “1234”, and then click the [OK] button. Enter “Density correction value” for “Patch No.” and “Temperature correction value” of the AD300 densitometer, if necessary.
6
Click the [Set] button.
7
Click the [OK] button. • Operation returns to the menu screen.
• Operation returns to the “Setup and Maintenance” screen.
164
distributed by www.minilablaser.com
F570
6.3.5 Paper Surfaces Display Setup (42R) Set the surface name display.
[Selection] “4 Setup and Maintenance” − “2 Print Condition Setup and Check” − “R Print Surfaces Display Setup”
165
distributed by www.minilablaser.com
F570
6.4
Printer Adjustment/Maintenance (5)
6.4.1 Paper Magazine Registration (451) This procedure registers the paper magazine to be used. Change the dryer temperature if necessary.
[Selection] “4 Setup and Maintenance” − “5 Print Condition Setup and Check” − “1 Paper Magazine Registration”
Type
: Select the paper type correctly. The paper type is indicated on the paper package. [Set] button : Click this button to register the entered items. ID : Enter the magazine ID. P1R : Enter the P1R replenishment rate. P2R : Enter the P2R replenishment rate. PSR : Enter the PSR replenishment rate. Correct value:Enter the correction value of the dryer temperature. [Set] button : Click this button to register the entered items. Do not change the “P1R“, “P2R”, “PSR” and “Correct value” values.
1
Release the latches and open the paper magazine. Latches (2)
↓ [Next page] [Prev. page] ↑
Paper Magazine L2360
ID Width Paper Length Remain BP
: Enter the magazine ID. : Enter the paper width (mm). : Select the paper surface type. : Enter the roll paper length (m). : Enter remaining paper length (m). : Select “YES” or “NO” for back printing. Line speed : Selected automatically according to the “Type”.
166
distributed by www.minilablaser.com
F570
2
Remove the two screws and adjust the width of the paper guides. Tighten the two screws.
4
Align the holes in the paper flange bosses with the paper width marks visible from the hole and tighten the four screws.
Screws (2) Paper Guides
Paper Flanges Hole/Width Mark
L2361
Screws (4)
Use the appropriate guides for paper width. Guide C is available as an optional accessory. Guide
L2368
NOTE:
Paper Width
A
Except B and C
B
95/120/130/210
C
114/216
Be careful not to overtighten the screws.
5
Find the appropriate paper from the table on the screen and install its ID chip to the magazine using the screw. ID Chip
Screw L2366
3
L2367
Loosen the four screws securing the paper flanges to the paper shaft.
6
Click the [Close] button. • Operation returns to the menu screen.
167
distributed by www.minilablaser.com
F570
6.4.2 Paper Magazine Feeding Fine Adjustment (452)
3
Click the [Print] button.
This menu should be executed for all paper magazines when installing the machine, or when a new magazine is registered.
[Selection]
Print 1
“4 Setup and Maintenance” − “5 Printer Adjustment/ Maintenance” − “2 Paper Magazine Feeding Fine Adjustment”
Print 2
• After about three minutes, Prints 1 and 2 are output to the sorter.
1 2
4
Set a new magazine on the upper magazine deck.
5
Select “Upper” for “Magazine”.
6
Enter new magazine ID in the “Magazine ID” box. Measure the feed lengths of Prints 1 and 2 at the center and record them. Enter the feed lengths recorded in the “Print 1” and “Print 2” boxes.
7
Click the [Set] button. • Feed length is adjusted automatically.
8
Install the magazine in the upper deck to the lower deck.
9
Repeat Steps 3 through 7 for the lower magazine.
10
Click the [Close] button.
• Operation returns to the menu screen.
168
distributed by www.minilablaser.com
F570
1
Enter the magazine ID to be adjusted in the “Magazine ID” box.
6.4.3 Test Pattern Printing (453) This procedure creates test pattern prints.
[Selection]
2
Select “Upper deck” or “Lower deck”.
3
Enter the value (mm) in the “New value” box.
4
Click the [Set] button.
“4 Setup and Maintenance” − “5 Printer Adjustment/ Maintenance” − “3 Test Pattern Printing”
• The feed length is changed.
5
Click the [Close] button. • Operation returns to the menu screen.
1
2 3 4
Move the cursor to “Test pattern selection”, and select “Grid”, “Borderless contact”, “Bordered contact”, “Gradation”, “Back print 1 (wedge)”, “Back print 2 (line)”, “Back print 3 (character)” or “Frame print”. Move the cursor to “Length” and enter the feed length (mm). Move the cursor to “Q’ty” and enter the number of prints. Click the [Print] button. • After about three minutes, the print is output to the sorter.
■ Color Drift Inspection 1) Make a grid test print. 2) Use a magnifying lens (X25) to check that the vertical line for the color drift is 1/8 pixel or less in width, and the horizontal line is 1/4 pixel or less in width. Reference: 1 pixel width = 0.08mm
5
Click the [Close] button. • Operation returns to the menu screen.
169
distributed by www.minilablaser.com
F570
Grid: For color drift and feed length inspection
Borderless contact: For exposure and processing unevenness inspection
Bordered contact: For exposure and processing unevenness, or white border inspection
Back print 1 (wedge)
Back print 2 (line)
Frame print
170
Gradation: For gradation inspection
Back print 3 (character)
distributed by www.minilablaser.com
F570
6.4.4 G Laser (SHG) Optimal Temperature Setup (454)
• The result is displayed.
The G laser optimal temperature setting message appears every three months. Set up the optimal temperatures on this screen.
[Selection] “4 Setup and Maintenance” − “5 Printer Adjustment/ Maintenance” − “4 G Laser (SHG) Optimal Temperature Setup”
2
Click the [Close] button. • Operation returns to the menu screen.
1
Click the [Enter] button.
171
distributed by www.minilablaser.com
F570
6.4.5 Paper Feed (455)
6.4.6 Printer Temperature Display (456)
This procedure feeds and processes unexposed sheets of paper.
This procedure displays the printer temperature and printer status.
[Selection]
[Selection]
“4 Setup and Maintenance” − “5 Printer Adjustment/ Maintenance” − “5 Paper Feed”
“4 Setup and Maintenance” − “5 Printer Adjustment/ Maintenance” − “6 Printer Temperature Display” NOTE: The temperatures are updated every five seconds. Always keep “ON” for “Working” of “Abnormal temp. detection”.
1
Enter the number of sheets in “Q’ty” box and the feed length in “Length” box.
Number of sheets: 1 to 999 Feed length: 82.5 to 381.0
1
Click the [Close] button. • Operation returns to the menu screen.
2
Click the [Enter] button. • The sheets of paper are fed and processed.
3
Click the [Close] button. • Operation returns to the menu screen.
172
distributed by www.minilablaser.com
F570
6.4.7 Printer Input Check (457)
6.4.8 Image Position and Tilt Fine Adjustment (458)
This procedure displays the status of the sensors.
[Selection]
This procedure adjusts the white border and image position in a template for each magazine ID.
[Selection] “4 Setup and Maintenance” − “5 Printer Adjustment/ Maintenance” − “8 Image Position and Tilt Fine Adjustment”
↓ [Next page] [Prev. page] ↑
1 2 3 1
4
Install the paper magazine to be adjusted on the upper paper deck. Select “Upper” or Lower for “Magazine”. Enter the feed length to be adjusted in the “Feed length” box. Click the [Print] button.
Click the [Close] button. • After about three minutes, the adjustment print is output.
• Operation returns to the menu screen.
5
Select the magazine ID to be adjusted.
173
distributed by www.minilablaser.com
F570
6
Measure the “X”, “Y”, “d” and “f” dimensions of the adjustment print and record them. y d
Feeding Direction
6.4.9 Printer I/O Check (45A) This procedure displays the status of the motors, solenoids and sensors.
Enter the recorded “X” and “Y” values (mm) in the appropriate “Main (X)” and “Sub (Y)” boxes.
8
Calculate “d - f” and enter the value in the “Tilt (d - f)” box.
9
Click the [Set] button.
10
Install the magazine to be adjusted on the lower magazine deck.
11
Select “Lower” for “Magazine”.
12
Repeat Steps 3 through 9.
13
Click the [Close] button.
↓ [Next page] [Prev. page] ↑
• Operation returns to the menu screen.
↓ [Next page] [Prev. page] ↑
174
distributed by www.minilablaser.com
F570
↓ [Next page] [Prev. page] ↑
6.4.10 Printer Function Select (45B) [Selection] “4 Setup and Maintenance” − “5 Printer Adjustment/ Maintenance” − “B Printer Function Select”
1
Click the required operation button. • The respective motor or solenoid operates if it is normal.
2
Click the [Close] button. • Operation returns to the menu screen.
1
Select “Both” for “Magazine” normally.
2
Select “YES” for “Registration”.
NOTE: Select “No” for “Registration” to use temporarily when the error “W-2414” or “W-2450” occurred.
3
Select “YES” for “Distribution”.
NOTE: Select “No” for “Distribution” to use temporarily when the error “W-2419” or “W-2455” occurred and adjust the pipe slider position of the distribution unit as described below. Large size prints cannot be printed. 1) Open the magazine door. 2) Open the distribution section inner cover. 3) Align the “ ”marks on the pipe slider and the distribution unit. 4) Close the distribution section inner cover. 5) Close the magazine door.
175
distributed by www.minilablaser.com
F570
6.4.11 Laser Exposure Check (45C)
Pipe Slider
This procedure performs an RGB test exposure and displays the results.
NOTE: When paper overlap feed has occurred, select “Change” for “Cut interval”. If the higher level is selected (from Level 1 to 3), the cut interval is increased and the processing ability is decreased.
5
Click the [OK] button. • Operation returns to the menu screen.
176
1
Click the [Close] button. • Operation returns to the menu screen.
distributed by www.minilablaser.com
F570
6.4.12 R Laser (R-LD) Data (45D)
6.4.13 G Laser (G-SHG) Data (45E)
This procedure displays the R laser (R-LD) data in the EEPROM.
This procedure displays the G laser (G-SHG) data in the EEPROM.
[Selection]
[Selection]
“4 Setup and Maintenance” − “5 Printer Adjustment/ Maintenance” − “D R Laser (R-LD) Data”
“4 Setup and Maintenance” − “5 Printer Adjustment/ Maintenance” − “E G Laser (G-SHG) Data”
1
Click the [Close] button. • Operation returns to the menu screen.
1
Click the [Close] button. • Operation returns to the menu screen.
177
distributed by www.minilablaser.com
F570
6.4.14 B Laser (B-LD) Data (45F) This procedure displays the B laser (B-LD) data in the EEPROM.
[Selection] “4 Setup and Maintenance” − “5 Printer Adjustment/ Maintenance” − “F B Laser (B-LD) Data”
6.4.15 Scan/Scan Home Position Parameter (45G) This procedure displays the parameters for exposure positions. Normally parameter changing is unnecessary. When the result of Menu 0547 “Main Scanning Position Adjustment/Laser Beam Synchronous Rough Adjustment” should be altered purposely, change the parameters.
[Selection] “4 Setup and Maintenance” − “5 Printer Adjustment/ Maintenance” − “G Scan/Scan Home Position Parameter”
1
Click the [Close] button. • Operation returns to the menu screen.
1
Enter the scanning position/scanning home position parameters by clicking the [ ] and [ ] buttons. Unit Main scanning : Pixel Sub-scanning : Raster
2
Click the [Set] button to set the parameters.
3
Click the [OK] button. • Operation returns to the menu screen.
178
distributed by www.minilablaser.com
F570
6.4.16 Main Scan/Laser Beam Sync. Rough Adjustment (45H)
3
Measure the dimensions of A, B and C, then record them. ←→
This procedure performs the scanning adjustment and laser beam synchronization rough adjustment. A→ ←
→
C
←B
[Selection]
Sub-Scanning Line
“4 Setup and Maintenance” − “5 Printer Adjustment/ Maintenance” − “H Main Scan/Laser Beam Sync. Rough Adjust”
Rough Adjustment Block
Perform this adjustment after processing three or more sheets of paper because the feed length may not stabilize immediately after setting paper. Tolerance of measurement: Within 0.5mm
4 5 6 1 2
Install the paper magazine for the narrowest paper width being used.
7
Move the cursor to “A: Left measured value” and enter the measured A value. Move the cursor to “B: Right measured value” and enter the measured B value. Click the [Set] button of “Width direction (main scanning position)”. Click the [OK] button.
Click the [Print] button.
8 • The print is output in about three minutes.
9
Move the cursor to “C: Top measured value“ and enter the measured C value. Click the [Set] button of “Feeding direction (subscanning position)”.
179
distributed by www.minilablaser.com
F570
10
Click the [OK] button.
6.4.17 Laser Beam Sync. Fine Adjustment Print (45J) This procedure performs the fine adjustment of the laser beam synchronization.
[Selection]
11
12 13 14 15
Find the X coordinate which has the minimum color drift on the print for the vertical lines using an inverted magnifier (x20-40), and record the coordinate value and the drifted color (CMY) order from the left.
“4 Setup and Maintenance” − ”5 Printer Adjustment/ Maintenance” − “J Laser Beam Sync. Fine Adjustment Print”
Check and record the drifted color (CMY) order of the sub-scanning line from the top using an inverted magnifier (x20-40). Move the cursor to “X(Width)” and enter the measured X value. Move the cursor to “Y(Feed)” and enter the measured Y value.
1
Click the [Set] button of “Coordinate with least amount of color drift”.
16
Click the [OK] button.
17
Click the [Close] button.
2
• Operation returns to the menu screen.
3
Move the cursor to “Order of drifted colors for main scanning” and enter the drifted color order from the left recorded in “Main Scanning Position Adjustment/Laser Beam Sync. Rough Adjustment (Menu 0547)”. Move the cursor to “Order of drifted colors for sub-scanning” and enter the drifted color order from the top recorded in “Main Scanning Position Adjustment/Laser Beam Sync. Rough Adjustment (Menu 0547)”. Click the [Print] button.
• The print is output in about three minutes.
180
distributed by www.minilablaser.com
F570
NOTE: The adjustment print has twenty or twenty-five vertical and horizontal lines.
4
Find numbers that have the minimum color drift on the output print for the vertical and horizontal lines using the magnifier (x20-40).
6.4.18 Laser History Display (45K) Display the exposure time and current value of RLD, G-SHG and B-SHG.
[Selection] “4 Setup and Maintence” − “5 Printer Adjustment/ Maintenance” − “K Laser History Display”
5 6
Move the cursor to the “Best main scanning position” and enter the number of the vertical lines found.
1
Click the [Switch display] button to switch between the graph and numeric displays.
Move the cursor to the “Best sub-scanning position” and enter the number of the horizontal lines found.
7
Click the [Set] button.
8
Click the [OK] button.
2
Click the [Close] button. • Operation returns to the menu screen.
9
Click the [Close] button. • Operation returns to the menu screen.
181
distributed by www.minilablaser.com
F570
6.4.19 Paper Condition Setup Table (LUT) Copy (45L)
6.4.20 Printer Mechanical Fine Adjustment (45M)
This procedure copies the LUT (Look-up Table) from one magazine to another.
This procedure adjusts the printer mechanism.
[Selection] [Selection] “4 Setup and Maintence” − “5 Printer Adjustment/ Maintenance” − “L Paper Condition Setup Table(LUT) Copy”
“4 Setup and Maintenance” − “5 Printer Adjustment/ Maintenance” − “M Printer Mechanical Fine Adjustment”
1
1
Specify the ID of the source magazine.
2
Specify the ID of the destination magazine.
3
Click the [Enter] button.
2
• Copying is performed.
4
Click the [OK] button.
3
4 5
“Cutter: Feed motor stop timing”: Sets up the feed motor stop timing when supplying paper. Click the [Set] button. “Eject: Right/left speed control start timing”: Sets up the speed control start timing of the M665 motor when feeding sheet paper with single lane. Click the [Set] button. “Setup of precut length”: Sets up the leading end cut-off length of paper for each magazine when the new roll paper is set, or printing is performed after eight hours have elapsed from the last printing (rewinding paper). Click the [Set] button. “Adjustment for distributing position”: Adjusts distribution position and nip timing for each magazine. Click the [Set] button. Click the [Close] button. • Operation returns to the menu screen.
5
Click the [Close] button. • Operation returns to the menu screen.
182
distributed by www.minilablaser.com
F570
6.4.21 Printer Operation Data Display (45P) This procedure displays the printer operation data.
[Selection] “4 Setup and Maintenance” − “5 Printer Adjustment/ Maintenance” − “P Printer Operation Data Display”
6.4.22 Data Saving (45T) The parameters displayed can be written from the memory on the printer’s circuit board to the HD in the main control unit.
[Selection] “4 Setup and Maintence” − “5 Printer Adjustment/ Maintenance” − “T Data Saving”
1
Select the item to be saved.
2
Click the [OK] button.
↓ [Next page] [Prev. page] ↑
• The data is saved. • Operation returns to the menu screen.
↓ [Next page] [Prev. page] ↑
1
Click the [Close] button. • Operation returns to the menu screen.
183
distributed by www.minilablaser.com
F570
6.4.23 Data Download (45U)
6.4.24 Filter Replacement History (45a)
The parameters displayed can be written from the HD in the main control unit to the memory on the printer’s circuit board.
The laser optical unit air filter replacement history is displayed.
[Selection] [Selection] “4 Setup and Maintence” − “5 Printer Adjustment/ Maintenance” − “U Data Download”
1
Select the item to be downloaded.
2
Click [OK].
“4 Setup and Maintenance” − “5 Printer Adjustment/ Maintenance” − “a Filter Replacement History” [Replace] button : Click this button when the filter has been replaced. [Initialize] button : Click this button to initialize the replacement history.
• The data is downloaded.
3
Click the [OK] button.
1
Click the [Close] button. • Operation returns to the menu screen.
• Operation returns to the menu screen.
4
184
Shut down and restart the system.
distributed by www.minilablaser.com
F570
6.4.25 Feeding Position Sensor Fine Adjustment (45b)
6
Select “All IDs” or “Selected ID only”.
This procedure adjusts paper leading end position for supply process on the basis of the sensors.
[Selection] “4 Setup and Maintenance” − “5 Printer Adjustment/ Maintenance” − “b Feeding Position Sensor Fine Adjustment” NOTE: Perform this procedure for both upper and lower magazine decks.
7
Enter ID in the “ID” box if “Selected ID only” is selected.
8
Enter new adjustment value in the “New” box.
9
Click the [Set] button.
10
Click the [Close] button.
• Operation returns to the menu screen.
1
Select “Upper” or “Lower” for “Magazine”.
2
Click the [Print] button. • After about three minutes, adjustment Prints 1 and 2 are output.
3 4 5
Measure the feed length of Prints 1 and 2 and record them. Enter the recorded values in the “Measured” boxes for “Print 1” and “Print 2”. Click the [Calculate] button. • New adjustment values appear in the “Calculated” box.
185
distributed by www.minilablaser.com
F570
6.4.26 Image Position Initial Setting (45c)
Print 3 : Measure the B to F dimensions and enter them in appropriate boxes.
This procedure sets up the initial image position for all magazines.
A C
C
[Selection] D
“4 Setup and Maintenance” − “5 Printer Adjustment/ Maintenance” − “c Image Position Initial Setting” B
D
F
E Print 2
E Print 1
C
1 2
Install the narrowest paper magazine on the upper deck and the widest paper magazine on the lower deck. D
Click the [Print] button.
B
• After about three minutes, adjustment Prints 1 and 2 for the upper magazine and Print 3 for the lower magazine are output.
3
Print 1 : Measure the A to F dimensions and enter them in the appropriate boxes. Print 2 : Measure the C and E dimensions and enter them in the appropriate boxes.
E Print 3
4
Click the [Set] button.
5
Click the [Close] button. • Operation returns to the menu screen.
186
F
distributed by www.minilablaser.com
F570
6.4.27 Sub-scan Feeding Speed Adjustment (45d) This procedure adjusts the feeding speed of the sub-scanning unit.
This procedure adjusts the soft nip timing, nip position and motor current value of the subscanning unit.
[Selection] “4 Setup and Maintenance” − “5 Printer Adjustment/ Maintenance” − “e Sub-scanning Soft Nip Fine Adjustment”
Select “Upper” or “Lower” for “Magazine”. Click the [Print] button. • After about three minutes, the adjustment print is output.
3
6.4.28 Sub-scanning Soft Nip Fine Adjustment (45e)
1
Enter the feed length in the “Feed length” box.
2
Select “Upper” or “Lower” for “Magazine”.
3
Click the [Print] button.
Measure the “A” dimension of the adjustment print and record it. Enter the recorded value in the “Measured” box. Click the [Calculate] button. • New adjustment value is displayed in the “Calculated (%)” box.
6
Enter the magazine ID in the “ID” box.
7
Enter the calculated value in the “New” box.
8
Click the [Set] button.
9
Click the [Close] button.
• After about three minutes, adjustment Prints 1 to 9 are output.
4 5 6
Select optimum prints for unevenness level at the leading and trailing ends from nine adjustment prints. Enter the optimum print numbers in the “Tip No. 1 to 9” and “End No. 1 to 9” boxes. Click the [Convert] button. • Timing, new pulse adjustment and motor current values are displayed.
7
Select “Selected ID only” or “All IDs”.
• Operation returns to the menu screen.
187
distributed by www.minilablaser.com
F570
8
Enter the ID in the “Magazine ID” box if “Selected ID only” is selected.
6.4.29 Sensor Calibration (Initial) (45f) This procedure calibrates the paper sensors.
2) Loosen the screw and remove the water supply port inner cover. Screw
This procedure measures and corrects the replenisher pump output. Normally measure only PSR. NOTE: The machine automatically measures and adjusts the pump output for P1R, P2RA and P2RB. When executing this menu to confirm pump operation for the P1R, P2RA or P2RB, return the discharged replenisher into the replenisher tank.
Perform the following steps for P1R, P2RA or P2RB.
1) Open the replenisher box door. 2) Remove the circulation filter tray.
1
Prepare a measuring cylinder.
2
Perform the following steps for PSR.
Circulation Filter Tray
1) Open the water supply port door.
190
LII232
distributed by www.minilablaser.com
F570
6
3) Remove the screw and then the splashprevention cover. Screw
Before the pump starts discharging, disconnect the replenisher nozzle, insert it into the measuring cylinder and hold it at the same height as its setting position. PSR Replenisher Nozzle
Measuring Cylinder Splash-prevention Cover
4
• The replenisher pump starts discharging after the countdown.
Click the [Start] button for the pump to be measured. • The message below appears on the printer operation panel. #PSR MEASURE #START
5
L21050
L21051
[YES]
?
Press the [Enter] key on the printer operation panel. • The alarm beeps intermittently for ten seconds.
• The alarm beeps when discharging is completed.
7 8 9
Insert the replenisher nozzle into the sub-tank. Place the measuring cylinder on a level surface, and then read and record the output. PSR : Dispose of the liquid in the measuring cylinder. P1R, P2RA or P2RB : Return the discharged replenisher into the replenisher tank through the cartridge box opening. P2RB Replenisher Nozzle P1W Replenisher Nozzle P1R Replenisher Nozzle
NOTE: Click the [Cancel] button to stop the operation.
Measuring Cylinder
P2RA Replenisher Nozzle L21052
191
distributed by www.minilablaser.com
F570
10
Select the “Measured value” box, and enter the recorded output value.
6.5.2 Auto Cleaning Output Measurement/Setting (462)
11
Clean the measuring cylinder.
12
Click the [OK] button.
This procedure measures and corrects autocleaning pump output.
• Operation returns to the menu screen.
13
Reinstall the removed parts.
[Selection] “4 Setup and Maintenance” − “6 Processor Adjustment/Maintenance” − “2 Auto Cleaning Output Measurement/Setting”
1 2 3
Prepare the two measuring cups for autocleaning output measurement. Open the dryer unit and support it with Stopper 2 (yellow). Remove the No.2 crossover rack. No.2 Crossover Rack
No.3 Crossover Rack L21121
NOTE: Do not remove the other crossover racks to prevent splashing of washing water.
192
distributed by www.minilablaser.com
F570
4
Install the measuring cups instead of the No.2 crossover rack as shown.
7
Remove the measuring cups. Measuring Cups
Measuring Cups
L21116
5
Click the [Start] button for “No.2”. • The message bellow appears on the printer operation panel. #No.2 MEASURE #START
6
[YES]
?
Press the [Enter] key on the printer operation panel. • The pump discharges washing water after the ten second countdown.
NOTE: To stop discharging, press the [Enter] key. • The alarm beeps once when the discharging is completed.
L21117
8 9 10 11 12
Place the measuring cups on a horizontal surface, read the liquid amount and record it. Dispose of the water from the measuring cups. Enter the recorded value in the “Measured value” box for the “No.2”. Reinstall the No.2 crossover rack and remove the No.3 crossover rack. Install the measuring cups instead of the No.3 crossover rack.
13
Repeat Steps 5 through 10 for No.3.
14
Reinstall the No.3 crossover rack.
15
Repeat Steps 5 and 6 for “Dryer entrance rack”. Dryer Entrance Rack
L2236
193
distributed by www.minilablaser.com
F570
16 17 18
Remove the dryer entrance rack and check that it is wet completely with washing water.
6.5.3 Processing Temperature Setting (463)
Reinstall the dryer entrance rack and close the dryer unit.
This procedure sets the processing temperatures.
Click the [OK] button.
• Operation returns to the menu screen.
[Selection] “4 Setup and Maintenance” − “6 Processor Adjustment/Maintenance” − “3 Processing Temperature Setting”
1
2
Enter the numerical values of the “P1”, “P2” and “PS” processing temperatures. Range
Initial Value
P1
40.0 to 45.0
43.0
P2
35.0 to 45.0
43.0
PS
42.0 to 47.0
45.0
Click the [OK] button. • Operation returns to the menu screen.
194
distributed by www.minilablaser.com
F570
6.5.4 Low Volume Processing Setup (466)
6.5.5 Processor Temperature Calibration (467)
This procedure sets up low volume processing.
This procedure calibrates the processor section temperatures.
Enter minimum processing amount in the box. Range: 0.0 to 25.0
3
Enter minimum processing amount for the last eight days in the box. Range: 0.0 to150.0
[Selection] “4 Setup and Maintenance” − “6 Processor Adjustment/Maintenance” − “7 Processor Temperature Calibration”
1 2
Check that the display values have reached the “Setting” temperatures. Open the dryer unit and support it with Stopper 2 (yellow).
3
Open the replenisher box door.
4
Remove the circulation filter tray. P1 Circulation Filter
NOTE: Click the [Clear] button to clear all data.
4
Click the [OK] button. • Operation returns to the menu screen.
Circulation Filter Tray L2233
195
distributed by www.minilablaser.com
F570
5 6
Remove the P1 circulation filter and put it on the circulation filter tray.
11
Measure the PS1/2/3 solution temperature at the PS2 processing tank and record it.
Measure the temperature of the P1 processing solution and record it. P1 Sub-tank
Thermometer
Thermometer
PS2 Sub-tank L21048
12 P2 Sub-tank L21047
7 8
13
Reinstall the filter by aligning the fastening tab with the notch, and then turn it 90° clockwise.
Repeat Steps 8 and 9 for the PS1/2/3 solution temperature. Remove the water supply port inner cover and rubber plug from the PS4 sub-tank. PS4 Sub-tank
If the “Setting” temperatures differ from the values displayed, move the cursor to the “Measured value” and enter the values recorded in Step 6. Range: 0.0 to 99.9
9 10
Click the [Enter] button. Thermometer
Repeat Steps 4 through 9 for the P2 solution temperature.
L21049
14 15 16 17
Measure the PS4 solution temperature and record it. Repeat Steps 8 and 9 for the PS4 solution temperature. Reinstall the rubber plug, water supply port inner cover and circulation filter tray. Click the [Close] button.
• Operation returns to the menu screen.
196
distributed by www.minilablaser.com
F570
6.5.6 Processor Input Check (468)
6.5.7 Processor I/O Check (46A)
This procedure displays the status of the sensors.
This procedure displays the status of the motors, solenoids and sensors.
“4 Setup and Maintenance” − “6 Processor Adjustment/Maintenance” − “C Processor Operation Data Display”
1
Enter level in the “Measurement level” box. Standard Level : 6
1
Click the [Close] button.
NOTE: The level may not be “6” according to the factory adjustment.
• Operation returns to the menu screen.
2 3
Click the [Set] button. Click the [Start] button for “Manual measurement” . • The required setting level is displayed in the “OK level” box.
4
Click the [Close] button. • Operation returns to the menu screen.
199
distributed by www.minilablaser.com
F570
6.6
Option Adjustment / Maintenance (7)
6.6.1 COM Port Setting (47A) Set the serial communication port for the PU800BA.
[Selection] “4 Setup and Maintenance” − “7 Option Ajustment / Maintenance” − “A COM Port Setting”
200
distributed by www.minilablaser.com
F570
6.7
Special Operations (9)
6.7.1 Paint (49A)
6.7.2 Explorer (49B)
Follow this procedure to use “Paint”.
Follow this procedure to use Explorer .
[Selection]
[Selection]
“4 Setup and Maintenance” − “9 Special Operations” − “A Paint”
“4 Setup and Maintenance” − “9 Special Operations” − “B Explorer”
NOTE: For information on “Paint” operations, see the Windows 2000 manual.
NOTE: For information on “Explorer” operations, see the WindowsR 2000 manual.
1 1
Click “File” and “Exit” in the upper left-hand corner of the screen.
Click “File” and “Exit” in the upper left-hand corner of the screen.
NOTE: Be sure not to click the emergency button.
NOTE: Be sure not to click the emergency button.
• Operation returns to the menu screen.
• Operation returns to the menu screen.
201
distributed by www.minilablaser.com
F570
6.7.3 Command (49C) Follow this procedure to perform MS-DOS command operations.
[Selection] “4 Setup and Maintenance” − “9 Special Operations” − ”C Command” NOTE: For information on “Command” operations, see the MS-DOSR manual.
1
Click the [X] button in the upper right-hand corner of the screen. • Operation returns to the menu screen.
202
distributed by www.minilablaser.com
7
Error Messages and Countermeasures
7.1
Error Indication Rule
7.1.1 Message Number
7.1.3 X-#### Actions
The messages are identified by the following four codes.
X-#### errors (software error) Take the following actions.
Symbol
Error
E
Trouble (Error requires action of the service representative.)
W
Mismatching of condition (Error can be corrected by the operator.)
I
Information
X
Software trouble
1. 2. 3. 4.
Write down the error No. Restart the system. Reinstall the software if the problem persists. Create the report in the specified format.
The first two digits indicate the location or operation of the error occurred. No.
Error Location
11XX
Scanner
12XX
CTB20 circuit board
13XX
Scanner image processing
14XX
Film carrier
15XX
Operation
21XX
Scanner to printer interface
22XX
Printer operation
23XX
Printer control
24XX
Paper feed
25XX
Laser printer
26XX
Processor
7.1.2 Message Icons Icon
Error Errors with code “E” (Take measures after turning OFF the power supply.)
Errors with code “E” , “W” or “X” (Error can be recovered.)
For code “I” (Information)
203
distributed by www.minilablaser.com
7.2 No W-1402
W-1403
W-1406
W-1408
Messages Message
Factor
Actions
Printer temperature adjustment not stabilized. perform pre-scan.
The printer laser temperature adjustment has not reached the specified value. (Not printed due to specification change)
—
Processor temperature adjustment not stabilized. perform Pre-scan.
The temperature adjustments of the processing tanks have not attained the specified values. (Not printed due to specification change)
—
"%MAGAZINE% not installed or paper end processing in progress. After green LED lights on magazine section door, install magazine and restart printing.
"Printing was performed without magazine installed.
Back print cannot be performed with specified paper. Press [Continue] to perform printing without back print.
Back printing command was issued for the medium weight paper. During the normal printing, the magazine with the postcard ID was detected. 1. Wrong magazine was used, or wrong print mode was selected.
—
2. Magazine ID sensor failure 3. Magazine malfunctions W-1418
I-1420
I-1421
W-1422
E-1425
W-1426
204
1. Install the correct magazine or select the postcard printing mode. 2. Replace the magazine ID sensor. 3. Replace the magazine.
%MAGAZINE% not installed or currently in paper end process. Install magazine and restart printing.
A magazine is not installed when the index format inconsistency ckeck is started.
Post-operational check cannot be started because printer is still processing another job.
Printing was in progress when starting the post-operational check.
—
Printer processor is busy. Please wait a moment, and then perform "Post-operational check“.
NG received from the printer during the post-operational check.
—
Connection with printer failed.
No response from the printer during the post-operational check. 1. 1394(interface cable) malfunction, disconnection or connection error of grounding wire. 2. 1394 CB failure
Printer initialization failed. Call technical representative. Press [Shutdown] to shutdown the system. Press [S-alone] to perform FMP Controller stand-alone operation at next start-up.
Initializing of printer failed at the system start-up. 1. 1394(interface cable) malfunction, disconnection or connection error of grounding wire. 2. 1394 CB failure 3. System software failure
Remote printer operation failed. and perss [Retry].
The printer's remote power ON failed at system start-up.
—
1. Connect the cable correctly, or replace the cable.
2. Replace the 1394 CB.
1. Connect the cable correctly, or replace the cable.
2. Replace the 1394 CB. 3. Restart the system software. If problems persist, reinstall it. —
distributed by www.minilablaser.com
No W-1427
W-1428
W-1441
Message Connection with printer failed. After connection is established, click [Retry].
Connection with printer failed. Confirm connection with printer, click [Retry].
Software error occurred. Restart the FMPC and printer.
Factor Error returned when the printer status registering command was issued at the system start-up. 1. 1394(interface cable) malfunction, disconnection or connection error of grounding wire. 2. System software failure
1. Connect the cable correctly, or replace the cable.
Error returned when magazine reading command was issued at the system start-up. 1. 1394(interface cable) malfunction, disconnection or connection error of grounding wire. 2. System software failure
1. Connect the cable correctly, or replace the cable.
NG returned when reading the parameter set from the resource manager. 1. System software failure 2. PC failure
W-1442
Software error occurred. Restart the FMPC and printer.
Error returned when JOB list was started. 1. System software failure 2. PC failure
E-1443
Communication error occurred while sending images from FMPC to printer. Inspect it referring to manual.
Error occurred when the images were transferred from FMPC to printer. 1. 1394(interface cable) malfunction, disconnection or connection error of grounding wire. 2. 1394 CB failure 3. System software failure 4. PC failure
W-1448
Back printer not installed. Install back printer properly.
Actions
Back printer not installed. 1. Installing of back printer failed. 2. Connection error or harness disconnection between the back printer sensor and PDC CB connector. 3. Back printer sensor failure. 4. PDC CB failure 5. CTL CB failure
2. Restart the system software. If problems persist, reinstall it.
2. Restart the system software. If problems persist, reinstall it.
1. Restart the system software. If problems persist, reinstall it. 2. Replace the PC.
1. Restart the system software. If problems persist, reinstall it. 2. Replace the PC.
1. Connect the cable correctly, or replace the cable.
2. Replace the 1394 CB. 3. Restart the system software. If problems persist, reinstall it. 4. Replace the PC. 1. Install the back printer correctly. 2. Connect the cable correctly, or replace the cable.
3. Replace the sensor. 4. Replace the PDC CB. 5. Replace the CTL CB.
W-1452
Printer cannot start printing because of %PRINTER_STATUS%.
Clear the problem and resume printing.
A printer on-line error occurred during the consistency check.
X-1454
Internal error.
Restart scanner and printer.
A JOB bag level error has occurred.
205
distributed by www.minilablaser.com
No E-1472
Message A communication error occurred between FMPC and printer. Call technical representative.
Factor Command sending error between FMPC and printer. 1. 1394(interface cable) malfunction, disconnection or connection error of grounding wire. 2. 1394 CB failure 3. System software failure
Actions
1. Connect thr cable correctly, or replace the cable.
2. Replace the 1394 CB. 3. Restart the system software. If problems persist, reinstall it.
W-1461
Reading digital image file failed. Digital image print cancelled.
Couldn't read the file print image from Imaging Controller.
1. Check the image file and its file format. 2. Restart the Imaging Controller.
W-1462
Digital image processing error. Printing digital image cancelled. File format incorrect.
File format error in DI Controller.
1. Restart the Imaging Controller. 2. Replace the Imaging Controller's hard disk.
I-1463
Digital image read cancelled due to error occurrence.
Some images may not be printed. Check print results. An error occurred while performing “File to print”.
—
Printer not in stand-by. Current printing order cancelled.
Printing command was issued while the printer was not in STANDBY.
—
Hard disk failure occurred during the data copy. Copying data cancelled.
Consult technical representative.
E-1482
Hard disk failure occurred. Consult technical representative.
Hard disk failure is detected during the file I/O.
W-1484
Initializing of printer failed. Press [S-alone] to perform FMP Controller stand-alone operation at next start-up.
Initializing of printer failed at the system start-up. 1. 1394 cable connection error
1. Connect the 1394 cable correctly. 2. Connect the connector correctly. 3. Replace CTP CB. 1. Match the paper types in upper and lower magazines.
W-1495
Auto is currently selected. Match the paper types of the upper and lower magazines. Press [Output] to output forcibly.
When switching the magazine, mismatch in paper type (surface or emulsion type) of upper and lower magazines occurred.
I-1501
Selected function cannot be used.
Unsupported function was selected.
—
I-1502
Insert FD.
FD insertion prompted at time of data backup.
—
W-1503
FD not inserted.
FD was not inserted during FD reading. 1. FD is not inserted. 2. FD drive failure
I-1504
W-1505
206
Insert next FD.
Wrong FD inserted. Insert correct FD.
When writing to multiple FDs at time of data backup, this message prompts you to insert the next FD. Incorrect FD is inserted. 1. FD is corrupted. 2. FD drive failure
1. Set the FD. 2. Replace the FDD. —
1. Set the correct FD. 2. Replace the FDD.
distributed by www.minilablaser.com
No E-1506
Message Reading of control information file failed. Selected image cannot be displayed.
Factor Files required to read the images couldn't be read. 1. System software failure 2. PC failure
I-1507
Data backup completed abnormally.
Data backup failure.
I-1508
Cancel data backup.
Data backup was cancelled by the command issued by operator.
W-1509
Not enough free space on hard disk. Unnecessary files have been deleted.
At the system start-up, specified HD free space for application was not reserved.
W-1510
Date value exceeds the limit. (1998/01/01 00:00:00 - 2100/12/31 23:59:59)
Date values exceeds the limit. 1. Incorrect date entry 2. System software failure 3. PC failure
W-1511
W-1512
W-1521
W-1522
W-1523
Next timer-ON time exceeds the limit. (1998/01/01 00:00:00 - 2100/ 12/31 23:59:59) Confirm the present time.
Insufficient FD free space. Insert correct FD.
Next start-up time exceeds the limit. 1. Incorrect date entry 2. System software failure
Actions
1. Restart the system software. If problems persist, reinstall it. 2. Replace the PC. — — 1. If there are unnecessary files in D drive, delete them.
1. Enter the correct date/time. 2. Restart the system software. If problems persist, reinstall it. 3. Replace the PC.
3. PC failure
1. Enter the correct date/time. 2. Restart the system software. If problems persist, reinstall it. 3. Replace the PC.
FD has not enough free space. 1. FD full 2. FDD failure
1. Insert the new FD. 2. Replace the FDD.
PU800B is not turned ON or is disconnected. Check the connection with PU800B. Press [Retry] to retry or [Cancel] to cancel.
—
PU800B is not turned ON or is disconnected. Check the connection with PU800B. Press [Retry] to retry or [Cancel] to cancel.
—
Retry it and if this error persists, consult your technical representative.
Retry it and if this error persists, consult your technical representative.
Pricing unit is not turned ON or is disconnected. Check the connection with PU800B. Press [Retry] to retry. To cancel printing invoice, press [Cancel]. To stop it, press [Stop].
—
W-1524
Backup data for PU800B cannot be read.
—
Consult your technical representative.
W-1525
Backup data for PU800B cannot be written.
—
Consult your technical representative.
I-1526
Production information log file not found. Create a new file.
Production information log file reading error
W-1527
Production information cannot be written into file.
Production information log file writing error. 1. System software failure 2. PC failure
Retry it and if this error persists, consult your technical representative.
—
1. Restart the system software. If problems persist, reinstall it. 2. Replace the PC.
Device registration to FDi failed. Check network connections. To retry the registration, press [Retry].
Factor Error in registering the FDiA logical output device. 1. Imaging Controller software failure. Error in registering the FDiA logical output device. 1. Imaging Controller is turned OFF. 2. LAN cable connection error 3. Imaging Controller software failure.
W-1534
Order not unlocked. Check the network connections.
Communication error from Imaging Controller occurred during the order processing in FRONTIER. 1. LAN cable connection error 2. Imaging Controller software failure.
W-1535
E-1536
E-1537
E-1539
W-1541
Cannot be serviced. Check the network connections.
Communication error from DI Controller occurred during the order processing in FRONTIER. 1. LAN cable connection error
1. Connect the LAN cable correctly. 2. Restart the system software. If problems persist, reinstall it.
Incorrect status or no device permission. 1. Imaging Controller software failure.
1. Restart the system software. If problems persist, reinstall it.
Cannot be serviced. Consult technical representative.
Other errors in FDiA 1. Imaging Controller software failure.
1. Restart the system software. If problems persist, reinstall it.
Cannot be serviced. Consult technical representative.
An order is in “waiting” status. 1. Imaging Controller software failure.
1. Restart the system software. If problems persist, reinstall it.
Print service not performed. Check the network connections.
Communication error from DI Controller occurred during the order processing in FRONTIER. 1. LAN cable connection error
Cannot be serviced. Consult technical representative.
Print service not performed. Check the network connections.
Error occurred when the status was changed during the normal printing. 1. LAN cable connection error
Print service not performed. Check the network connections.
Error occurred when the status was changed during the normal printing. 1. LAN cable connection error 2. Imaging Controller software failure.
208
1. Start up the Imaging Controller. 2. Connect the LAN cable correctly. 3. Restart the system software. If problems persist, reinstall it.
2. Imaging Controller software failure.
2. Imaging Controller software failure. W-1543
1. Restart the system software. If problems persist, reinstall it.
1. Connect the LAN cable correctly. 2. Restart the system software. If problems persist, reinstall it.
2. Imaging Controller software failure. W-1542
Actions
1. Connect the LAN cable correctly. 2. Restart the system software. If problems persist, reinstall it.
1. Connect the LAN cable correctly. 2. Restart the system software. If problems persist, reinstall it.
1. Connect the LAN cable correctly. 2. Restart the system software. If problems persist, reinstall it
distributed by www.minilablaser.com
No W-1544
Message Print service not performed. Check the network connections.
Factor Error occurred when order completion is noticed. 1. LAN cable connection error 2. Imaging Controller software failure.
W-1545
Print service not performed. Check the network connections.
Error occurred during order deletion. 1. LAN cable connection error 2. Imaging Controller software failure.
W-1546
Print service not performed. Check the network connections.
Error occurred when the status is changed while no order is registered. 1. LAN cable connection error 2. Imaging Controller software failure.
W-1547
Print service not performed. Check the network connections.
Error occurred during order reading process. 1. LAN cable connection error 2. Imaging Controller software failure.
W-1548
E-1549
The printer is not in STAND-BY. Press [Resume] to try again. Cannot be serviced. Consult technical representative.
1. Connect the LAN cable correctly. 2. Restart the system software. If problems persist, reinstall it.
Order that was not being processed was deleted. 1.Imaging Controller software failure.
1. Restart the system software. If problems persist, reinstall it.
E-1596
Service info cannot be read. Check the network connections.
FDI error occurred during reading the service name. 1. LAN cable connection error 2. Imaging Controller software failure.
As for the next piece of print, the width of paper is mismatched to the magazine.(???mm) Press [Order] to output forcibly per Order. Press [Image] to output forcibly per Image. When replacing the magazine, press [OK] after the initialization of printer is completed. To stop printing, press [Abort].
1. Connect the LAN cable correctly. 2. Restart the system software. If problems persist, reinstall it.
1. Turn the printer to STANDBY.
Image export/import service name reading message.
W-1621
1. Connect the LAN cable correctly. 2. Restart the system software. If problems persist, reinstall it.
1. Printer is not in STANDBY.
Reading service name list. Wait.
Uncompleted orders remain. They will be printed next time at the time of starting.
1. Connect the LAN cable correctly. 2. Restart the system software. If problems persist, reinstall it.
Printer STANDBY notice error.
I-1594
W-1620
Actions
—
1. Connect the LAN cable correctly. 2. Restart the system software. If problems persist, reinstall it.
—
If the [OK] button is pressed, the post-operational process will be started. To continue printing, press the [Cancel] button to proceed [Main Menu] - [2 Print].
—
Press the [Order] button to output all current images forcibly. Press the [Image] to output forcibly the image currently processed only. It is recommended that you replace the magazine for the correct one, then press the [OK] button after initializing the printer, and then perform printing again. If the [Abort] button is pressed, the printing process will be stopped.
209
distributed by www.minilablaser.com
No W-1622
W-1626
W-1627
W-1662
W-1751
Message As for the next piece of print, the paper type is mismatched to the magazine. Press [Order] to output forcibly per Order. Press [Image] to output forcibly per Image. When replacing the magazine, press [OK] after the initialization of printer is completed. To stop printing, press [Abort]. As for the next piece of print, the width of paper or the paper type is mismatched to the magazine.(???mm) Press [Order] to output forcibly per Order. Press [Image] to output forcibly per Image. When replacing the magazine, press [OK] after the initialization of printer is completed. To stop printing, press [Abort].
Factor
—
—
“Auto” is currently selected. Match the paper types of the upper and lower magazines. Press [Output] to output forcibly.
—
Work can't be finished because PU800B is while printing is processed. Wait to the printing management end for about %NUM% seconds.
—
Couldn’t send the status information. Check the network connections.
Status information sending error. 1. LAN cable connection error 2. DI Controller software failure.
W-1902
W-1903
W-1930
W-1931
W-1932
210
Actions Press the [Order] button to output the current images forcibly. Replace the magazine for the correct one, then press the [OK] button after initializing the printer, and then perform printing again. If the [Abort] button is pressed, the printing process will be stopped.
Press the [Order] button to output all current images forcibly. Press the [Image] to output forcibly the image currently processed only. It is recommended that you replace the magazine for the correct one, then press the [OK] button after initializing the printer, and then perform printing again. If the [Abort] button is pressed, the printing process will be stopped. Press the [Abort] button, then select [Upper] or [Lower] in “Switch Magazine”.
—
1. Connect the LAN cable correctly. 2. Restart the system software. If problems persist, reinstall it.
Cannot print because the printer memory is full. Retry printing when enough memory is reserved.
Enough memory cannot be reserved in operation SS because too many printing (scanning) requests are issued.
—
Cannot output because the image data occupy large amounts of memory. Wait until enough memory is reserved and retry.
Enough memory cannot be reserved in operation SS because too many outputting requests are issued.
—
%MAGAZINE% not installed or paper end processing in progress. After the door LED in the magazine section turns green, install magazine and restart printing.
The magazine is not installed.
%MAGAZINE% not installed or paper end processing in progress. After the door LED in the magazine section turns green, install magazine and restart printing.
A magazine not found when the index format inconsistency check is started.
Print size and magazine paper width mismatched, or change print size. Press [Output] to output forcibly.
The print size and the paper width of the selected magazine mismatched.
—
—
—
distributed by www.minilablaser.com
No W-1938
I-1939
W-8101
Message
Factor
Print size exceeds the limit. Change print size.
The selected print size (in feed direction) exceeds the value available in 10GD.
The post-operational check cannot be started because printing is in progress or the printed paper remains in the printer.
A post-operational check was started while the printer was in use.
Communication with Frontier Manager failed. The orders with the installed papers will be printed preferentially. To use scheduling function, return to Main Menu and check connection, then resume printing. —
W-8102
Paper (width and paper type) and magazines are mismatched to the next order. Exchange the magazine after the display to be able to exchange the magazine afterwards appears. Press [Output] output forcibly.
—
Actions —
—
Wait for a moment with no operation, so this message will disappears, then other print-waiting orders with the setting of paper that matches the currently installed paper will be printed automatically, while skipping the order with the mismatched paper setting. To replace the magazine with the correct one, click the [OK] button. Unless the orders with mismatched paper are urgent ones, it is recommended to print the possible orders first, then the remaining orders after replacing the magazine. To replace the magazine with the correct one, click the [OK] button. To output the current orders forcibly, press the [Output] button.
211
distributed by www.minilablaser.com
8
Measures against FMPC Failures
8.1
To Return to Direct-connecting Type in FRONTIER 350/370
To return to the direct-connecting type in FRONTIER 350/370, use the following procedures. (IEEE1394 board also functions as repeater.) Make sure that the FMPC is turned ON, and that at least one IEEE1394 board is normally operated.
1
On the “Main Menu” screen in the scanner (SP), select [4 Setup and Maintenance], then click the [OK] button.
3
4 If the "initializing of printer failed" message appears, click the [Retry] button to clear it, and then perform the procedures.
2
212
In the “Login” dialog, select [SE2] as user name and enter the password “7777”, and then click the [OK] button.
Select [41 System Operation Setup and Check] [41F Installation Information Setup], then click the [Start] button.
The “[41F] Installation Information Setup” screen appears.
distributed by www.minilablaser.com
5
6 7
8
Set to [ON] for [Printer].
On the “Main Menu” screen in the scanner (SP), select [3 Post-operational Check], then click the [OK] button, then shut down the scanner.
On the “Main Menu” screen in the FMPC, select [3 Post-operational Check], then click the [OK] button, then shut down the FMPC and printer (LP).
9
Connect the IEEE1394 cable from printer and the one from scanner to the connectors on the same board in the FMPC.
Switch the display to the FMPC by pressing the button in the switcher.
IEEE1394 from printer (LP)
IEEE1394 from scanner (SP)
MP019
The display can be switched also by pressing the [Ctrl] key twice swiftly.
MP011
10
Insert the FD without the system program into the FD drive of the FMPC, and then turn it ON. Make sure that the FD does not contain the executable file.
• After start-up, the error message “Non-System disk or disk error” appears, and the “Windows” is not started up.
213
distributed by www.minilablaser.com
11
Turn on the printer, then set the switch to STANDBY. In this case, the printer (LP) cannot be started up remotely by turning on the scanner (SP).
12
Turn on the scanner (SP).
EZ1192
13
After the restart, the “Main Menu” screen appears.
IMPORTANT To perform printing from the Imaging Controller, set up the FMPC logical device name on the administration screen in each DI application on the Imaging Controller.
214
distributed by www.minilablaser.com
8.2
To Return to Direct-connecting Type in FRONTIER 355/375
To return to the direct-connecting type in FRONTIER 355/375, use the following procedures. (IEEE1394 board also functions as repeater.)
1
On the “Main Menu” screen in the scanner (SP), click the [Setup and Maintenance] button.
If the “Setup and Maintenance” screen does not appear, start up the FRONTIER in the stand-alone mode.
2
4
5
Set to [ON] for [Printer].
Enter the password “7777”, and then click the [OK] button.
6 3
The [0140 Installation Information Setup] screen appears.
On the “Main Menu” screen in the scanner (SP), click the [Post-operational Check] button, then shut down the scanner.
Select [01 System Operation Setup and Check] [0140 Installation Information Setup].
215
distributed by www.minilablaser.com
7
Switch the display to the FMPC by pressing the button in the switcher.
10
Connect the IEEE1394 cable prom printer (LP) to the scanner (SP).
MP019 MP048
The display can be switched also by pressing the [Ctrl] key twice swiftly.
8
9
On the “Main Menu” screen in the FMPC, select [3 Post-operational Check], then click the [OK] button, then shut down the FMPC and printer (LP).
Turn on the printer (LP). In this case, the printer(LP) cannot be started up remotely by turning on the scanner (SP).
12
Turn on the scanner (SP).
ZII040
Disconnect the IEEE1394 cable from the scanner (SP).
MP047
216
11
distributed by www.minilablaser.com
13
After the restart, the “Main Menu” screen appears.
IMPORTANT To perform printing from the Imaging Controller, set up the FMPC logical device name on the administration screen in each DI application on the Imaging Controller.
217
distributed by www.minilablaser.com
9
Index
A [A1] Stand-alone Upgrade in SP [Ver.1.5 -> Ver.1.7] and DI Print/Data Writing Software [C4/C5] Client Installation in SP ......................87 [A1] Stand-alone Version-up and DI Print/Data Writing Software Installation in SP...................61 Accumulated Production Information (413) ......................................................... 105, 154 Auto Cleaning Output Measurement/Setting (462) ...................................................................192 Auto-cleaning Pump Output Measurement .........138
Creating Backup FD for SP-3000 and LP5700 ..... 30
D Data Backup (417) ......................................... 108, 157 Data Download (45U) .................................... 135, 184 Data Saving (45T) .......................................... 135, 183 DI Manager Administrative Setting (41I) ..... 110, 159 DI Print/Data Writing Software [C4/C5] Client Installation in FMPC ........................................... 69 Disabling Network Connection on SP Side ................................................... 38, 60, 86 Disabling of “Rack Auto Cleaning” ................... 53, 78
B B Laser (B-LD) Data (45F) .....................................178
E
B Laser (B-SHG) Data (45F) .................................128 Back Print Setup (42O) ...........................................117 Back Printer Test (45N) ..........................................134 Back Printing Setup (42O) .....................................164 Bios Setup ..................................................................16
Enabling of “Rack Auto Cleaning” .................... 73, 99 Error Indication Rule ............................................... 203 Error Information Check (415) ...................... 107, 156 Error Messages and Countermeasures ............... 203 Ethernet Cable ........................................................... 10 Evaporation Correction Rate Setting (465) ......... 142 Explorer (48B) .......................................................... 148 Explorer (49B) .......................................................... 201 Extension Cable for Keyboard ................................. 10
C Changing Mode from SP-3000 to FMPC ...............31 Checking the Kit Contents........................................11 Clear Error Log (41E)..................................... 109, 158 COM Port Setting (47A)..........................................200 Command (48C) ......................................................149 Command (49C) ......................................................202 Connecting FMPC, FRONTIER, LAN Cable and Monitor Switcher ............................ 31, 56, 81 Control Strip Processing .........................................113 Copying Print Size Table from SP to FD ...............30 Copying Print Size Table to FD then Copying LP1500/2000 Print Size Table to FMPC .........98 Copying Print Size Table to FD then Copying SP-3000 Print Size Table to FMPC .................71 Copying SP-3000 Print Size Table to FMPC ........40 Creating Backup FD for FMPC, SP1500/2000 and LP1500/2000 .............................................100 Creating Backup FD for FMPC, SP-3000 and LP1500/2000 ...............................................74 Creating Backup FD for FMPC/SP-3000 ...............50 Creating Backup FD for SP1500/2000, LP1500/2000 .......................................................79 Creating Backup FD for SP-3000 and LP1500/2000 .......................................................54
218
F Feeding Position Sensor Fine Adjustment (45b) ................................................................... 185 Filter Replacement History (45a) .......................... 184 FMPC [D20] Installation (Reinstall) with Printer’s Backup FD ........................................... 66 FMPC [D20] Software Installation (Reinstall) with Printer's Backup FD ................................... 92 FMPC Output Device Setting in Imaging Controller ................................................ 44, 72, 99
G G Laser (G-SHG) Data (45E) ....................... 128, 177 G Laser (SHG) Optimal Temperature Setup (454) ........................................................ 171 G, B Laser (SHG) Optimal Temperature Setup (454) ........................................................ 122
H How to Read This Manual .......................................... 9
distributed by www.minilablaser.com
I
N
IEEE1394 Board Installation ....................................15 IEEE1394 Driver Installation in SP .........................60 IEEE1394 Driver Pre-installation ............... 29, 63, 89 Image Position and Tilt Fine Adjustment (458) ...173 Image Position Fine Adjustment (458) .................124 Image Position Initial Setting (45c) .......................186 Input/Output Device Setup for FMPC .....................41 Installation for FRONTIER 350/370 ........................76 Installation for FRONTIER 355/375 ........................51 Installation for FRONTIER 570................................14 Installation Information Confirmation (416) .........108 Installation Information Reference (416)..............157 Installation Information Setup (41F) ............ 110, 159
M Main Scan/Laser Beam Sync. Rough Adjustment (45H) ..............................................179 Main Scanning Position Adjustment/Laser Beam Sync. Rough Adjustment (45H) ..........129 Maintenance Menu (FRONTIER 350/370/355/375).......................102 Maintenance Menu (FRONTIER 570) ..................150 Measures against FMPC Failures.........................212 Message Icons .........................................................203 Message Number ....................................................203 Messages..................................................................204
O Operational Check ...................................... 45, 75, 101 Operational Procedure................................... 102, 150 Option Adjustment / Maintenance (7) ................... 200 Output Device Setup for SP and Restarting SP ............................................... 70, 97
P Paint (48A) ................................................................ 148 Paint (49A) ................................................................ 201 Paper Condition Method Setup (42J) .......... 117, 163
219
distributed by www.minilablaser.com
Processor I/O Check (46A) ........................... 145, 197 Processor Operating Condition Setup (46B) .......................................................... 146, 198 Processor Operation Data Display 2 (46E) .........147 Processor Operation Data Display (46C) ... 146, 199 Processor Temperature Calibration (467) .. 143, 195 Production Information 1 (411) ..................... 103, 151 Production Information 2 (412) ..................... 104, 152 PS Liquid Concentration Management (46G) .....199
R R Laser (R-LD) Data (45D) ........................... 127, 177 Recommended Monitor Switcher ............................10 Recommended PC ....................................................10 Replacing the ROM for Printer ......................... 55, 80 Replenisher Pump Output Measurement ............137 Replenisher Pump Output Measurement/Setting (461) ...................................................................190 Replenisher Rate Setup (464) ...............................141 Required Tools and CDs ..........................................13
Starting-up LP in ROM Mode and Checking ROM Version (2.0-0x-000) ......................... 65, 90 Sub-scan Feeding Speed Adjustment (45d) ....... 187 Sub-scanning Soft Nip Fine Adjustment (45e).... 187 System Operation Setup and Check (1) .............. 151 System Operation Setup and Check (41) ............ 103 System Shutdown....................................... 50, 75, 101
T Test Pattern Printing (453) ............................ 121, 169 Timer Setup (414)........................................... 106, 155 Timer Setup in FMPC ............................................... 42 To Return to Direct-connecting Type in FRONTIER 350/370 ......................................... 212 To Return to Direct-connecting Type in FRONTIER 355/375 ......................................... 215 Turning on FMPC ............................................... 60, 85 Turning on FMPC and Installing LP5700 Driver .................................................................... 36 Turning on Imaging Controller ................................. 41 Turning on LP5700 .................................................... 35
S Scanning Position/Scanning Home Position Parameter Setup (45G) ...................................129 Scan/Scan Home Position Parameter (45G) ......178 Sensor Calibration (Daily) (45g) ............................189 Sensor Calibration (Initial) (45f).............................188 Setup of Remaining Space in Hard Disk ...............18 SP-3000 Monitor's Power Cable .............................10 Special Operations (48) ..........................................148 Special Operations (9) ............................................201
220
U User Registration ....................................................... 21
W Windows Settings ...................................................... 22 Windows XP Installation and Partitioning .............. 16
X X-#### Actions ......................................................... 203
distributed by www.minilablaser.com
FAX : 81-3-5484-0454
Questionnaire concerning This Manual Fujifilm’s Technical Division Photo Products Marketing would be most grateful if you would make copies of this form, then complete and send them to us by FAX. Your opinions will contribute greatly to an accurate assessment of the overall quality of each manual. All questions can be answered by ticking [✓] the appropriate box(es), but in addition to these answers, please provide us with your written comments in the lined spaces following each block of questions. Title : FRONTIER 350/370 355/375/570
Frontier Manager Printer Controller Ver.2.0 INSTALLATION/SERVICE MANUAL/PARTS LIST Reference Number : PP3-A1060E
Manual Title and Reference Number
Name :
Your Name and Company
Company :
E-mail Address :
Your E-mail Address and FAX Number
Question 1
•
•
Question 2
•
FAX Number :
How would you rate this manual overall? (1) Very easy to use and understand
(2) Fairly easy to use and understand
(3) Slightly difficult to use and understand
(4) Very difficult to use and understand
Please provide us with your reasons and comments.
Have you found any technical errors, errors in spelling, or missing words in this manual? Yes
Question 3
No
•
If you have ticked (Yes), please let us know what these errors and missing words are.
•
How would you rate the writing (language, choice of words/phrases, etc.) and the illustrations/ diagrams, etc.? (1) Clear and easy to follow
(2) Should be simplified
(3) Difficult to follow (1)’ [Illustrations, etc.] Of adequate size (2)’ [Illustrations, etc.] Too small (3)’ [Illustrations, etc.] Difficult to follow •
If you have ticked (2), (3) or (3)’, please give us your reasons.
Additional Comments/ Requests concerning This Manual Please return this questionnaire to :
FAX No. : Tokyo 81-3-5484-0454
distributed by www.minilablaser.com
FUJI PHOTO FILM CO., LTD. 26-30, Nishiazabu 2-chome, Minato-ku, Tokyo 106-8620, Japan. Printed on Recycled Paper Ref.No.PP3-A1060E ESD-05.01-FG Printed in Japan
