Gpon – Basic Command Olt Huawei – Networking.from.Zero

5/3/2018

GPON – Basic Command OLT Huawei – NETWORKING.FROM.ZERO

NETWORKING.FROM.ZERO Keep Your Spirit To Learn , and Never Give up To Learn WRITTEN BY NETWORKINGFROMZEROMARCH 31, 2017JUNE 20, 2017

GPON – Basic Command OLT Huawei Continuing previous article about some Basic Command in OLT ZTE. Now, it’s time to share about some basic Commands at OLT Huawei. Nowadays GPON Technologies have adopted to many brands Like Cisco , Alcatel Lucent / Nokia , Huawei , ZTE , Fiberhome , and etc. I have knowledge with some brands like ZTE , Huawei , Fiberhome , and Alcatel Lucent. but mostly with ZTE and Huawei. At Least Their Concept is all same. That’s same like Topology Below :

There is Always OLT and ONT. Okay , Here we go of some basic Commands At OLT Huawei.

Checking OLT Uptime https://networkingfromzero.wordpress.com/2017/03/31/gpon-basic-command-olt-huawei/

1/22

5/3/2018


OL01#display sysuptime System up time: 324 day 20 hour 55 minute 38 second

Checking OLT Board OL01#display board 0 ————————————————————————SlotID BoardName Status SubType0 SubType1 Online/Offline ————————————————————————0 1 H805GPFD Normal 2 H805GPFD Normal 3 H805GPFD Normal 4 H805GPFD Normal 5 H805GPFD Normal 6 H805GPFD Normal 7 H802SCUN Active_normal –> Control Module 8

H802SCUN Standby_normal

–> Control Module

9 10 11 12 13 14 15 16 17

H805GPFD H805GPFD H805GPFD H805GPFD H805GPFD H805GPFD H805GPFD H805GPFD H801X2CS

Normal Normal Normal Normal Normal Normal Normal Normal Normal

–> Uplink Module

18

H801X2CS Normal

–> Uplink Module

19 H801PRTE Normal 20 H801PRTE Normal ————————————————————————OL01#

Checking OLT processor and Memory per Slot

https://networkingfromzero.wordpress.com/2017/03/31/gpon-basic-command-olt-huawei/

2/22

5/3/2018


OL01#display mem 0/1 Memory occupancy: 33% OL01#display cpu 0/1 Send message for inquiring board cpu occupancy successfully, board executing… CPU occupancy: 15% OL01#

Checking OLT Temperature OL01#display temperature 0 SlotID: 1 BoardName: H805 SlotID: 2 BoardName: H805

Temperature: 42C( 107F) Temperature: 41C( 105F

Finding ONT by SN number


3/22

5/3/2018


OL01#display ont info by-sn ABCDEF —————————————————————————– In Huawei port 1 = port 0 at system F/S/P : 0/1/0 (remember) this ONT Meaning that locate at slot 1 port 0 onu id 2 ONT-ID :2 Control flag : active Run state : offline Config state : initial Match state : initial DBA type : SR ONT distance(m) :– ONT baery state :– Memory occupation :– CPU occupation :– Temperature :– Authentic type : SN-auth SN : ABCDEF (HWTC-07930A53) Management mode : OMCI Software work mode : normal Isolation state : normal ONT IP 0 address/mask : – Description : IRONMAN Last down cause : dying-gasp –> down caused by dying gasp (dying-gasp = ont off ) Last up time

: 2016-11-11 17:52:08+07:00 –> Log Last Uptime

Last down time : 2016-11-15 09:23:27+07:00 Last dying gasp time : 2016-11-15 09:23:27+07:00 ONT online duration : – Type C support : Not support Interoperability-mode : Unknown

Checking ONT Status OL01#display ont info 0 1 0 all —————————————————————————– F/S/P ONT SN Control Run Config Match Protect ID flag state state state side —————————————————————————– 0/ 1/0 1 ABCDEF deactivated offline initial initial no 0/ 1/0 2 REZABU active offline initial initial no — 0/ 1/0 4 BAREZU active online normal match no –> ONT online


4/22

5/3/2018


Checking ONT History Logs OL01#config OL01(config)#interface gpon 0/1 OL01(config-if-gpon-0/1)#display ont register-info 0 1 —————————————————————————— Index : 10 Auth-type : SN-auth SN : ABCDEF (HWTC-19698F53) TYPE : 245H UpTime : 2016-11-02 16:56:37+07:00 DownTime : 2016-11-04 07:52:15+07:00 DownCause : ONT dying-gasp —————————————————————————— Index :9 Auth-type : SN-auth SN : ABCDEF (HWTC-19698F53) TYPE : 245H UpTime : 2016-10-31 22:29:05+07:00 DownTime : 2016-11-02 16:42:36+07:00 DownCause : ONT dying-gasp —————————————————————————— Index :8 Auth-type : SN-auth SN : ABCDEF (HWTC-19698F53) TYPE : 245H UpTime : 2016-10-29 00:25:35+07:00 DownTime : 2016-10-31 22:13:03+07:00 DownCause : ONT dying-gasp

checking ONT mac address


5/22

5/3/2018


OL01#display mac-address port 0/1/0 ont 2 ———————————————————————– SRV-P BUNDLE TYPE MAC MAC TYPE F /S /P VPI VCI VLAN ID INDEX INDEX ———————————————————————– 2389 – gpon aaaa-bbbb-cccc dynamic 0 /1 /0 2 2 122 2388 – gpon bbbb-aaaa-cccc dynamic 0 /1 /0 2 1 212 ———————————————————————– Total: 2 Note: F–Frame, S–Slot, P–Port, F/S/P indicates PW Index for PW, A–The MAC address is learned or configured on the aggregation port, VPI indicates ONT ID for PON, VCI indicates GEM index for GPON, v/e–vlan/encap, pritag–priority-tagged, ppp–pppoe, ip–ipoe, ip4–ipv4oe, ip6–ipv6oe OL01#

Checking ONT power OL01#config OL01(config)#interface gpon 0/1 OL01(config-if-gpon-0/1)#display ont optical-info 0 all —————————————————————————– ONT Rx power Tx power OLT Rx ONT Temperature Voltage ID (dBm) (dBm) power(dBm) (C) (V) (mA) —————————————————————————– 4 -23.10 2.30 -24.21 56 3.260 13 6 -21.08 2.28 -21.49 44 3.240 13

Current

Checking ONT Version


6/22

5/3/2018


OL01#display ont version 0 1 0 4 ————————————————————————– F/S/P : 0/1/0 ONT-ID :4 Vendor-ID : HWTC ONT Version : 49 Product-ID :4 Equipment-ID : 24 Main Software Version : V3R0 Standby Software Version : V3R0 OntProductDescription : EchoLife Support XML Version : 1.3. OL01#

Checking ONT IP (Routing Mode) OL01#display ont wan-info 0/1 0 4 ——————————————————————— F/S/P : 0/1/0 ONT ID :4 ——————————————————————— Index :1 Name : OLT_C_INTERNET_DHCP_WAN Service type : Internet Connection type : IP routed IPv4 Connection status : Connected IPv4 access type : DHCP IPv4 address : 1.2.3.4 Subnet mask : 255.255.255.0 Default gateway : 1.2.3.1 Manage VLAN : 212 Manage priority :0 Option60 : Yes Switch : Enable MAC address : BBBB-AAAA-CCCC Priority policy : Specified L2 encap-type : IPoE IPv4 switch : Enable IPv6 switch : Disable ——————————————————————— OL01#

Checking ONT port status https://networkingfromzero.wordpress.com/2017/03/31/gpon-basic-command-olt-huawei/

7/22

5/3/2018


OL01#config OL01(config)#interface gpon 0/1 OL01(config-if-gpon-0/1)#display ont port state 0 4 eth-port all ————————————————————————– ONT-ID ONT ONT Speed(Mbps) Duplex LinkState RingStatus port-ID Port-type ————————————————————————– 4 1 GE – – down – 4 2 GE 100 full up – 4 3 GE – – down – 4 4 GE – – down – ————————————————————————– OL01(config-if-gpon-0/1)#

Checking ONT configuration OL01#display current-configuration ont 0/1/0 4 # [gpon] interface gpon 0/1 ont add 0 4 sn-auth “ABCDEF” omci ont-lineprofile-id 5 ont-srvprofile-id 1 desc “HULK” ont ipconfig 0 4 dhcp vlan 212 priority ont internet-config 0 4 ip-index 0 ont wan-config 0 4 ip-index 0 profile-id 1 ont port route 0 4 eth 1 enable –> routing mode ont port native-vlan 0 4 eth 2 vlan 122 priority 0 –> bridging mode ont port native-vlan 0 4 eth 3 vlan 122 priority 0 –> bridging mode ont port route 0 4 eth 4 enable –> routing mode # [bbs-config] service-port 2677 vlan 212 gpon 0/1/0 ont 4 gemport 1 multi-service user-vlan 212 tag-transform translate inbound traffic-table index 20 outbound traffic-table index 20 service-port 2678 vlan 122 gpon 0/1/0 ont 4 gemport 2 multi-service user-vlan 122 tag-transform translate inbound traffic-table index 0 outbound traffic-table index 0 return OL01#


8/22

5/3/2018


Checking ONT Configuration per-Port OL01#display current-configuration port 0/1/1 # [gpon] interface gpon 0/1 port 1 ont-auto-find enable –> Configuring this to detect your unregister ONU automatically

Checking How many Services per-ONT OL01#display service-port port 0/1/0 ont 4 { |e2e|gemport|sort-by }: Command: display service-port port 0/1/0 ont 4 Switch-Oriented Flow List —————————————————————————– INDEX VLAN VLAN PORT F/ S/ P VPI VCI FLOW FLOW RX TX STATE ID ATTR TYPE TYPE PARA —————————————————————————– 2677 212 common gpon 0/1 /0 4 1 vlan 212 20 20 up 2678 122 common gpon 0/1 /0 4 2 vlan 122 0 0 up —————————————————————————– Total : 2 (Up/Down : 2/0) Note : F–Frame, S–Slot, P–Port, VPI indicates ONT ID for PON, VCI indicates GEM index for GPON, OL01#

You can Ping From Your ONT :p


9/22

5/3/2018


OL01#config OL01(config)#interface gpon 0/1 OL01(config-if-gpon-0/1)#ont remote-ping 0 4 ip-address 8.8.8.8 OL01(config-if-gpon-0/1)# —————————————– ONT remote-ping information —————————————– F/S/P : 0/ 1/0 ONT-ID :4 ONT IP Index :0 IP address of ping : 8.8.8.8 Transmit packets : 4 Receive packets : 4 Lost packets :0 Lost packets ratio(%): 0 Min delay(ms) : 31 Max delay(ms) : 31 Average delay(ms) : 31 Error Code :– —————————————–

Reboot ONT OL01#config OL01(config)#interface gpon 0/1 OL01(config-if-gpon-0/1)#ont reset 0 4

Reset Factory ONT OL01#config OL01(config)#interface gpon 0/1 OL01(config-if-gpon-0/1)#ont factory-seing-restore 0 4

How To Release Renew ONT as DHCP client OL01#config OL01(config)#interface gpon 0/1 OL01(config-if-gpon-0/1)#ont ipconfig 0 4 dhcp reset


10/22

5/3/2018


Checking Rx Level For OLT Uplink OL01#config OL01(config)#interface giu 0/18 OL01(config-if-giu-0/18)#display port ddm-info 0 Temperature(C) : 38.640000 Supply voltage(V) : 3.260000 TX bias current(mA) : 38.000000 TX power(dBm) : 1.095110 RX power(dBm) : -14.659738 OL01(config-if-giu-0/18)#quit OL01(config)#quit OL01#

Reset Slot OL01#config OL01(config)#board reset 0/1

How To find ONT by Mac OL01#display location aaaa-bbbb-cccc { |fabric|ont }: Command: display location 4cf9-5dd3-1914 It will take several minutes, and console may be timeout, please use command idle-timeout to set time limit Are you sure to query MAC address location ? (y/n)[n]:y ———————————————————————– SRV-P BUNDLE TYPE MAC MAC TYPE F /S /P VPI VCI VLAN ID INDEX INDEX ———————————————————————– 5493 – gpon aaaa-bbbb-cccc dynamic 0 /6 /6 50 1 203 ———————————————————————– If U want to Explore More about other, My advice is using “?” symbol. I Hope this article can help you sometime.


11/22

5/3/2018


Report this ad

Report this ad POSTED IN GPON, HUAWEI.TAGGED #GPON #HUAWEI.

47 thoughts on “GPON – Basic Command OLT Huawei” 1.

PHAI VONE SAYS:

SEPTEMBER 19, 2017 AT 8:08 PM Thank you very much REPLY 2.

ANDERSON ANAEL SAYS:

JANUARY 3, 2018 AT 4:56 AM very important all command for OLT Huawei, tks a lot. Please, create article for configuration OLT Huawei MA5600T how-to REPLY https://networkingfromzero.wordpress.com/2017/03/31/gpon-basic-command-olt-huawei/

12/22

5/3/2018


1.

NETWORKINGFROMZERO SAYS:

JANUARY 3, 2018 AT 2:08 AM you’re welcome.. please see my other article.. how to register ont huawei..that’s how to create service REPLY NETWORKINGFROMZERO SAYS:

2.

JANUARY 3, 2018 AT 8:02 AM hps://networkingfromzero.wordpress.com/2017/06/21/how-to-register-ont-huawei/ REPLY 3.

ANDERSON ANAEL SAYS:

JANUARY 3, 2018 AT 8:20 PM my difficulty is being configure the OLT to work with the uplink port. I’m using the GICF 0/18 0 and VLAN150 board, my difficulty is being understand where tcon, gem, profile …. my goal is to just test in my office and leave OLT configured, tks a lot for all information REPLY 1.


JANUARY 4, 2018 AT 1:08 AM okay please try it and just modify vlan from my article.. i hope that’s configuration will be working..if any problem.. you can share here.. maybe i can help.. REPLY 4.

MARK SAYS:

JANUARY 9, 2018 AT 6:16 AM Hello, i got the script for changing traffic table display traffic table ip from-index 0 then service-port inbound traffice-table index outbound traffice-table index i change it to both service-port and the download rate changes, but the upload remain. can you please assist me why is that? thank you! REPLY 1.


JANUARY 9, 2018 AT 6:54 AM can you share full configuration about traffic table and service-port inbound above? REPLY 1.

NOKIE SAYS:

JANUARY 9, 2018 AT 7:40 AM


13/22

5/3/2018


———————————————— TD Index : 21 TD Name : Priority : 0 Copy Priority : – Mapping Index : – CTAG Mapping Priority: – CTAG Mapping Index : – CTAG Default Priority: 0 Priority Policy : local-pri CIR : 153600 kbps CBS : 4917200 bytes PIR : 512000 kbps PBS : 682750 bytes Fix : 0 kbps CAR Threshold Profile: – Color Mode : color-blind Color Policy : dei Referenced Status : used ———————————————— 2.


JANUARY 9, 2018 AT 11:12 AM maybe u can configure like this : UAWEI#display traffic table ip index 21 ———————————————— TD Index : 21 TD Name : ip-traffic-table_21 Priority : 0 Copy Priority : – Mapping Index : – CTAG Mapping Priority: – CTAG Mapping Index : – CTAG Default Priority: 0 Priority Policy : local-pri CIR : 153600 kbps CBS : 4917200 bytes PIR : 153600 kbps PBS : 4917200 bytes Fix : 0 kbps CAR Threshold Profile: – Color Mode : color-blind Color Policy : dei Referenced Status : used ———————————————— HUAWEI# https://networkingfromzero.wordpress.com/2017/03/31/gpon-basic-command-olt-huawei/

14/22

5/3/2018


###################################################### HUAWEI#display traffic table ip index 22 ———————————————— TD Index : 22 TD Name : ip-traffic-table_22 Priority : 0 Copy Priority : – Mapping Index : – CTAG Mapping Priority: – CTAG Mapping Index : – CTAG Default Priority: 0 Priority Policy : local-pri CIR : 512000 kbps CBS : 682750 bytes PIR : 512000 kbps PBS : 682750 bytes Fix : 0 kbps CAR Threshold Profile: – Color Mode : color-blind Color Policy : dei Referenced Status : used ———————————————— HUAWEI# ################## service-port xxxxx inbound traffic-table index 21 outbound traffic-table index 22 5.

PRINCE SHRESTHA SAYS:

JANUARY 31, 2018 AT 5:00 AM Can any one help me to display the optical power from all users from an OLT? REPLY 1.


JANUARY 31, 2018 AT 10:12 AM i never do it like that ,, but this is command for looking optical power from all ont in one port olt huawei HW01(config)#interface gpon 0/1 HW01(config-if-gpon-0/1)#display ont optical-info 0 all —————————————————————————– ONT Rx power Tx power OLT Rx ONT Temperature Voltage Current ID (dBm) (dBm) power(dBm) (C) (V) (mA) —————————————————————————– 3 -20.86 1.90 -23.02 42 3.300 16 6 -22.22 2.22 -23.38 43 3.240 13 8 -22.92 2.35 -25.09 50 3.240 17 https://networkingfromzero.wordpress.com/2017/03/31/gpon-basic-command-olt-huawei/

15/22

5/3/2018


9 -21.94 2.25 -22.45 41 3.200 12 10 -25.37 2.36 -23.47 54 3.280 12 11 -27.69 2.05 -24.82 58 3.280 15 12 -25.37 2.07 -24.32 54 3.280 14 13 -23.87 2.33 -26.39 54 3.240 14 14 -20.31 2.03 -21.94 45 3.240 14 17 -25.37 2.36 -26.39 58 3.240 17 25 -20.00 2.08 -22.22 47 3.260 12 27 -20.75 1.94 -21.37 42 3.320 14 31 -22.07 2.37 -22.84 42 3.300 13 33 -22.14 2.02 -22.76 50 3.260 12 34 -21.25 2.08 -23.38 42 3.300 13 —————————————————————————– REPLY 6.

NOKIE SAYS:

JANUARY 31, 2018 AT 10:28 AM Question, while you modified some adjustments via console, it is normal, it is not updating on the imanager u2000 Gui? It is much easier to update via console/cli How to check/modify/delete logs command by a specific ip address. Thank you. REPLY 1.


JANUARY 31, 2018 AT 10:35 AM i just more like to update via cli.. yes it will update and nms too when we do some changes via cli… do you mean log config ?? REPLY 1.

NOKIEV SAYS:

JANUARY 31, 2018 AT 10:52 AM yes, how to check/modify/delete log config of a particular ip address? 2.


FEBRUARY 1, 2018 AT 10:52 AM there only to check that log by name or index.. not in particular ip address.. that’s command is display log cli name xxxx 3.

NOKIEV SAYS:

JANUARY 31, 2018 AT 10:55 AM in regards with auto update modification via cli to gui, is there on/off switch with that? in case while doing testing? 4.


FEBRUARY 1, 2018 AT 10:50 AM https://networkingfromzero.wordpress.com/2017/03/31/gpon-basic-command-olt-huawei/

16/22

5/3/2018


why do you want to stop?? 7.

NOKIEV SAYS:

JANUARY 31, 2018 AT 10:39 AM another, how to check the configuration/commands of a particular ont-lineprofile profile-id. thank you! REPLY 1.


FEBRUARY 1, 2018 AT 10:53 AM display ont-line-profile gpon all REPLY 1.

NOKIE SAYS:

FEBRUARY 1, 2018 AT 10:56 AM “display ont-line-profile gpon all” I would like to know te line command of the current configuration of a particular ontlineprofile. its like the line command of a port-ont account. 2.


FEBRUARY 1, 2018 AT 12:20 PM display current-configuration ont 0/2/2 10 3.


FEBRUARY 1, 2018 AT 12:21 PM that’s mean u want to see configuration ont from slot 2 port 2 onu 10 8.

NOKIE SAYS:

JANUARY 31, 2018 AT 5:27 PM Question, while you modified some adjust via console, it is normal, it is not updating on the imanager u2000 Gui? It is much easier to update via console/cli How to check/modify/delete logs command by a specific ip address. Thank you. REPLY 9.

NOKIE SAYS:

FEBRUARY 1, 2018 AT 10:54 AM “why do you want to stop??” To avoid confusiong while doing a testing. how about the current configuration of ont-lineprofile, how to check it? REPLY 1.



17/22

5/3/2018


FEBRUARY 1, 2018 AT 11:15 AM display current-configuration section global-config REPLY 1.

NOKIE SAYS:

FEBRUARY 1, 2018 AT 12:16 PM “display current-configuration section global-config” it worked thank you! another question, how to check the total available/total bandwidth. 2.


FEBRUARY 1, 2018 AT 12:20 PM you’re welcome ..for the olt u mean,, u can check in uplink interace 10.

NOKIE SAYS:

FEBRUARY 1, 2018 AT 1:01 PM “you’re welcome ..for the olt u mean,, u can check in uplink interace ” what is the exact command? thank you! REPLY 1.


FEBRUARY 1, 2018 AT 2:21 PM it depends on your uplink device from olt .. for example your uplink olt connect to cisco switch.. just show interface in cisco switch you will see the utilization of olt.. that is an easy way if u check from olt .. tomorrow i will find a way how to check statistic from uplink REPLY 1.


FEBRUARY 15, 2018 AT 1:28 PM Here’s the command to check statistic from uplink port OL01-HW#config OL01-HW(config)#interface giu 0/18 OL01-HW(config-if-giu-0/18)#display port traffic 0 The received traffic of this port(packets/s) =307216 The received traffic of this port(octets/s) =370001834 The received traffic of this port(kbits/s) =2960014.7 The transmied traffic of this port(packets/s) =125081 The transmied traffic of this port(octets/s) =21000637 The transmied traffic of this port(kbits/s) =168005.1 https://networkingfromzero.wordpress.com/2017/03/31/gpon-basic-command-olt-huawei/

18/22

5/3/2018


OL01-HW(config-if-giu-0/18)# 11.

NOKIE SAYS:

FEBRUARY 15, 2018 AT 1:32 PM Here’s the command to check statistic from uplink port OL01-HW#config OL01-HW(config)#interface giu 0/18 OL01-HW(config-if-giu-0/18)#display port traffic 0 The received traffic of this port(packets/s) =307216 The received traffic of this port(octets/s) =370001834 The received traffic of this port(kbits/s) =2960014.7 The transmied traffic of this port(packets/s) =125081 The transmied traffic of this port(octets/s) =21000637 The transmied traffic of this port(kbits/s) =168005.1 OL01-HW(config-if-giu-0/18)# On the above example, is that right, it is a 3gbps connection? I’ll try it later. REPLY 1.


FEBRUARY 15, 2018 AT 1:33 PM yes 2,96 Gb actually REPLY 1.

NOKIE SAYS:

FEBRUARY 15, 2018 AT 1:45 PM One more question, how about the vlan 100/0 is not connected, only vlan 10/0. And it is fixed to a particular ip add/subnet mask? How to do that? 2.


FEBRUARY 15, 2018 AT 1:50 PM can you show me where is part the vlan 10 can connect and vlan 100 can’t connect because i’m still not understand the question .. beer we compare the configuration between both vlan .. that’s same or not?? 12.

NOKIE SAYS:

FEBRUARY 15, 2018 AT 1:57 PM can you show me where is part the vlan 10 can connect and vlan 100 can’t connect because i’m still not understand the question .. beer we compare the configuration between both vlan .. that’s same or not?? ================================= https://networkingfromzero.wordpress.com/2017/03/31/gpon-basic-command-olt-huawei/

19/22

5/3/2018


On this page, you can query the connection and line status of the WAN port. IPv4 Information WAN Name Connection Status IP Acquisition Mode IP Address Subnet Mask VLAN/Priority MAC Address Connected 1_TR069_R_VID_100 Connecting DHCP — — 100/0 AlwaysOn 2_INTERNET_R_VID_10 Connected DHCP 10.x.x.x 255.255.252.0 10/0 AlwaysOn The above is the status of the modem. Why is that? The vlan 100/0 is connecting/not connected, only the vlan 10/0. The ip address is fixed. 10.x.x.x 255.255.252.0 REPLY 1.


FEBRUARY 15, 2018 AT 2:58 PM if u disable vlan 10 .. vlan 100 is working ?? REPLY 1.


FEBRUARY 16, 2018 AT 3:57 AM i mean , try to delete vlan 10 and that service .. and see what happen for vlan 100 , is it work or not ? if work maybe we can just activate for 1 dhcp service .. actually i am not ever set for 2 dhcp service in huawei , but in olt zte i already tried and it is work .. 13.

EUGENE ANCAJAS SAYS:

FEBRUARY 15, 2018 AT 4:11 PM hello , i have a problem with my configuration on OLT, i have the 3rd gpon card to be configured on port 1. my command wont go through (config)#service-port 33002 looks like it maxed out of the service port. REPLY 1.


FEBRUARY 15, 2018 AT 1:14 PM can you share full information when you execute the command.. REPLY NETWORKINGFROMZERO SAYS:

2.

FEBRUARY 15, 2018 AT 1:31 PM hps://networkingfromzero.wordpress.com/2017/06/21/how-to-register-ont-huawei/ i think when you configure service above u don’t need to assign the number of service index like that (33002) just skip the number,, because that will numbering automatically.. you just need to configure like this for example : OL01(config)#service-port vlan 111 gpon 0/1/2 ont 100 gemport 1 multi-service user-vlan 111 tagtransform translate inbound traffic-table index 100 outbound traffic-table index 100 REPLY https://networkingfromzero.wordpress.com/2017/03/31/gpon-basic-command-olt-huawei/

20/22

5/3/2018


14.

NOKIE SAYS:

FEBRUARY 16, 2018 AT 7:29 PM another question, how to check if the configuration of IPTV is working? below is my current configuration. ont-srvprofile gpon profile-id 1 profile-name “Fiber_IPTV” ont-port eth adaptive 8 multicast-forward untag multicast mode olt-control port vlan eth 1 translation 10 user-vlan 10 port vlan eth 2 translation 10 user-vlan 10 port vlan eth 3 translation 10 user-vlan 10 port vlan eth 4 translation 3225 user-vlan 3225 commit ont-lineprofile gpon profile-id 1 profile-name “Fiber_IPTV” tcont 1 dba-profile-id 1 REPLY 1.


FEBRUARY 18, 2018 AT 1:04 AM that’s configuration is defined to port configuration in ont and you need applied first in one ont,, after that because you just set the bridging vlan.. you must check that mac-address can read at OLT from suitable VLAN, after that because that is bridging, you need to check that the device already goen IP address in another device outside the OLT the above topology from OLT or u can check from STB device REPLY 1.

NOKIE SAYS:

FEBRUARY 18, 2018 AT 2:04 AM that’s configuration is defined to port configuration in ont and you need applied first in one ont,, after that because you just set the bridging vlan.. you must check that mac-address can read at OLT from suitable VLAN, after that because that is bridging, you need to check that the device already goen IP address in another device outside the OLT the above topology from OLT or u can check from STB device Thanks, can you post a working iptv working configuration + a command or how to how to test if it is working? Thank you! 2.


FEBRUARY 18, 2018 AT 2:40 AM you’re welcome ..maybe later :p 15.

SURAJ SAYS:

APRIL 19, 2018 AT 8:35 AM https://networkingfromzero.wordpress.com/2017/03/31/gpon-basic-command-olt-huawei/

21/22

5/3/2018


How to delete SN/ont from the olt ? REPLY 1.


APRIL 19, 2018 AT 9:09 AM just delete the onu in the interface gpon,, how to do it ,, you can read my another article hps://networkingfromzero.wordpress.com/2017/06/21/how-to-register-ont-huawei/ REPLY


22/22

Gpon – Basic Command Olt Huawei – Networking.from.Zero

Recommend Documents