MAINTENANCE MANUAL
KFS 576A CONTROL UNIT
Manual Number 006-15718-0000 Revision 0, Apr/2007
This document contains technical data and is subject to U.S. export regulations. These commodities, technology, or software were exported from the United States in accordance with the export administration regulations. Diversion contrary to U.S. law is prohibited.
Honeywell - Confidential THIS DOCUMENT AND ALL INFORMATION AND EXPRESSION CONTAINED HEREIN ARE THE PROPERTY OF HONEYWELL INTERNATIONAL INC., ARE PROVIDED IN C ONFIDENCE, AND MAY BE USED BY PERSONS REQUIRED BY FEDERAL AVIATION REGULATION PART 21.50 TO COMPLY WITH ANY OF THE TERMS OF THESE INSTRUCTIONS. INSTRUCTIONS. EXCEPT AS SET FORTH ABOVE, NO PERSON MAY, IN WHOLE OR IN PART, USE, DUPLICATE OR DISCLOSE THIS INFORMATION FOR ANY PURPOSE WITHOUT THE PRIOR WRITTEN PERMISSION OF HONEYWELL INTERNATIONAL INC.
This document contains technical data and is subject to U.S. export regulations. These commodities, technology, or software were exported from the United States in accordance with the export administration regulations. Diversion contrary to U.S. law is prohibited.
Honeywell - Confidential THIS DOCUMENT AND ALL INFORMATION AND EXPRESSION CONTAINED HEREIN ARE THE PROPERTY OF HONEYWELL INTERNATIONAL INC., ARE PROVIDED IN C ONFIDENCE, AND MAY BE USED BY PERSONS REQUIRED BY FEDERAL AVIATION REGULATION PART 21.50 TO COMPLY WITH ANY OF THE TERMS OF THESE INSTRUCTIONS. INSTRUCTIONS. EXCEPT AS SET FORTH ABOVE, NO PERSON MAY, IN WHOLE OR IN PART, USE, DUPLICATE OR DISCLOSE THIS INFORMATION FOR ANY PURPOSE WITHOUT THE PRIOR WRITTEN PERMISSION OF HONEYWELL INTERNATIONAL INC.
KFS 576A
Honeywell Materials License Agreement The documents and information contained herein ("the Materials") are the proprietary data of Honeywell International Inc. and Honeywell Intellectual Properties Inc (collectively "Honeywell"). These Materials are provided for the exclusive use of Honeywell Service Centers; Honeywell-authorized repair facilities; operators of Honeywell aerospace products subject to an applicable product support agreement, their wholly owned-subsidiaries or a formally designated third party service provider thereunder; and direct recipients of Materials from Honeywell's Aerospace Technical Publication Distribution. The terms and conditions of this this License Agreement govern your use of these Materials, except to the extent that any terms and conditions of another applicable agreement with Honeywell regarding the operation, maintenance, or repair of Honeywell aerospace products conflict with the terms and conditions of this License Agreement, in which case the terms and conditions of the other agreement will govern. However, this License Agreement will govern in the event of a conflict between its terms and conditions and those of a purchase order or acknowledgement. 1. License Grant Grant - If you are a party to an applicable product support agreement, a Honeywell Service Center agreement, or an authorized repair facility agreement, Honeywell hereby grants you a limited, non-exclusive license to use these Materials to operate, maintain, or repair Honeywell aerospace products only in accordance with that agreement. If you are a direct recipient of these Materials from Honeywell's Aerospace Technical Publication Distribution and are not a party to an agreement related to the operation, maintenance or repair of Honeywell aerospace products, Honeywell hereby grants you a limited, non-exclusive li cense to use these Materials to maintain or repair the subject Honeywell aerospace products only at the facili ty to which these Materials have been shipped ("the Licensed Facility"). Transfer of the Materials Materials to another facility owned by you is permitted only if the original Licensed Facility retains no copies of the Materials and you provide prior written notice to Honeywell. 2. Rights In Materials Materials - Honeywell retains all rights in these Materials and in any copies thereof that are not expressly granted to you, including all rights in patents, copyrights, trademarks, and trade trade secrets. No license to use any Honeywell trademarks or patents is granted under this License Agreement. 3. Confidentiality Confidentiality - You acknowledge that these Materials contain information that is confidential and proprietary to Honeywell. You agree to take all reasonable efforts to to maintain the confidentiality of these Materials. 4. Assignment And Transfer Transfer - This License Agreement may be assigned to a formally designated service designee to the extent allowed under an applicable product support agreement or transferred to a subsequent owner or operator of an aircraft containing the subject Honeywell aerospace products. However, the recipient of any such assignment or transfer must assume all of your obligations under this License Agreement. No assignment or transfer shall relieve any party of any obligation that such party then has hereunder. 5. Copies of Materials Materials - Unless you have the express written permission of Honeywell, you may not make or permit making of copies of of the Materials. Notwithstanding the foregoing, you you may make copies of only portions of the Material for your your internal use. You agree to return the Materials Materials and any copies thereof to Honeywell upon the request of Honeywell.
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission permission of Honeywell.
MLA-1
KFS 576A
6. Term Term - This License Agreement is effective effective until terminated as set forth forth herein. This License Agreement will terminate immediately, without notice from Honeywell, if you fail to comply with any provision of this License Agreement or will terminate simultaneously with the termination or expiration of your applicable product support agreement, authorized repair facility agreement, or your formal designation as a third party service provider. Upon termination of this License Agreement, you will return these Materials to Honeywell without retaining any copies and will have one of your authorized officers certify that all Materials have been returned with no copies retained. 7. Remedies Remedies - Honeywell reserves the right to pursue all available remedies and damages resulting from a breach of this License Agreement. 8. Limitation of Liability Liability - IN NO EVENT WILL HONEYWELL BE LIABLE FOR ANY INCIDENTAL DAMAGES, CONSEQUENTIAL DAMAGES, SPECIAL DAMAGES, INDIRECT DAMAGES, LOSS OF PROFITS, LOSS OF REVENUES, OR LOSS OF USE, EVEN IF INFORMED OF THE POSSIBILITY OF SUCH DAMAGES. TO THE EXTENT PERMITTED BY APPLICABLE LAW, THESE LIMITATIONS LIMITATIONS AND EXCLUSIONS WILL APPLY REGARDLESS OF WHETHER LIABILITY ARISES FROM BREACH OF CONTRACT, WARRANTY, TORT (INCLUDING BUT NOT LIMITED TO NEGLIGENCE), BY OPERATION OF LAW, OR OTHERWISE. 9. Controlling Law Law - This License shall be governed and construed in accordance with the laws of the State of New York without regard to the conflicts of laws provisions thereof. This license sets forth the entire agreement between you and Honeywell and may only be modified by a writing duly executed by the duly authorized representatives of the parties.
Copyright - Notice Copyright 2007 Honeywell 2007 Honeywell International Inc. All rights reserved.
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission permission of Honeywell.
MLA-2
KFS 576A
REVISION HIGHLIGHTS Par t Number 006-15718-0000
Rev 0, Apr/2007
Rev 0
Date Apr/2007
Description Original Is Issue.
©Honeywell International Inc. Do not print without express permission permission of Honeywell.
RH-1
KFS 576A
REVISION HIGHLIGHTS Par t Number
Rev 0, Apr/2007
Rev
Date
Description
©Honeywell International Inc. Do not print without express permission permission of Honeywell.
RH-2
KFS 576A
TABLE OF CONTENTS SECTION 4 THEORY OF OPERATION 4.1 4.2 4.2.1 4.2.2 4.2.3 4.2.4 4.2.5 4.2.6 4.2.7 4.2.8 4.2.9 4.2.10 4.3 4.3.1 4.3.1.1 4.3.1.2 4.3.2 4.3.2.1 4.3.2.2 4.3.2.3 4.3.2.4 4.3.2.5 4.3.2.6 4.3.2.7 4.3.2.8 4.3.3 4.3.3.1 4.3.3.2
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GENERAL CIRCUIT THEORY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CONTROL UNIT INPUTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FUNCTION SWITCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CODE SELECTOR SWITCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . IDENT SWITCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . OPERATING VOLTAGES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EEPROM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MULTIPLEX AND DISPLAY CIRCUITRY . . . . . . . . . . . . . . . . . . . . . . . . . . . CLOCK, STROBE AND SERIAL DATA OUTPUTS . . . . . . . . . . . . . . . . . . . . TRANSPONDER SELECT SWITCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 429 BUS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DETAILED CIRCUIT THEORY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . POWER SUPPLY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +5 VOLT REGULATOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . HIGH VOLTAGE CURRENT LIMITER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MICROPROCESSORS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ALTITUDE INPUTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . REPLY INPUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CLOCK, STROBE AND SERIAL DATA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . MODE A/B SELECT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 429 BUS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EEPROM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MICROPROCESSOR RESET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SWITCH INPUTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DISPLAY CIRCUITRY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ANODE AND CATHODE DRIVERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AUTOMATIC DIMMING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-1 4-1 4-1 4-1 4-2 4-2 4-2 4-2 4-2 4-3 4-3 4-3 4-3 4-3 4-3 4-4 4-4 4-4 4-4 4-4 4-5 4-5 4-6 4-6 4-6 4-7 4-7 4-8
SECTION 5 MAINTENANCE 5.1 5.2 5.2.1 5.2.2 5.2.3 5.2.4 5.2.4.1 5.2.4.2 5.2.4.3 5.2.4.4 5.2.4.5
GENERAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TEST AND ALIGNMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TEST EQUIPMENT REQUIRED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DESCRIPTION OF KFS 576A TEST PROGRAM . . . . . . . . . . . . . . . . . . . . . ALIGNMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FINAL TEST. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ON/OFF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DISPLAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FLIGHT LEVEL (FL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . IDENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CODE SELECTOR SWITCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
5-1 5-1 5-1 5-2 5-3 5-3 5-5 5-5 5-5 5-6 5-6
TOC-1
KFS 576A
TABLE OF CONTENTS 5.2.4.6 EMERGENCY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7 5.2.4.7 REPLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7 5.2.4.8 DIMMING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7 5.2.4.9 EXTERNAL STANDBY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7 5.2.4.10 CONTROL DISABLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7 5.2.4.11 NON VOLATILE MEMORY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7 5.2.4.12 CHANNELING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-8 5.2.4.13 429 I/O . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-8 5.2.4.14 VFR CODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-9 5.2.4.15 UNIT STATUS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-9 5.2.4.16 FINAL TEST DATA SHEET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-10 5.3 OVERHAUL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-12 5.3.1 VISUAL INSPECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-12 5.3.3 REPAIR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-14 5.3.4 DISASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-15 5.3.4.1 COVER REMOVAL (047-5021-02) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-15 5.3.4.2 MICROPROCESSOR BOARD REMOVAL (200-6580-XX) . . . . . . . . . . . . . 5-15 5.3.4.3 FRONT COVER/SWITCH BOARD REMOVAL (088-1166-XX/200-6589-XX) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-15 5.3.4.4 DRIVER BOARD REMOVAL (200-6626-XX) . . . . . . . . . . . . . . . . . . . . . . . 5-16 5.3.4.5 ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-16 5.4 TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-16 SECTION 6 ILLUSTRATED PARTS LIST 6.1 6.2
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1 BILL OF MATERIAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
TOC-2
KFS 576A
LIST OF FIGURES Figure 4-1 Figure 4-2 Figure 4-3 Figure 4-4 Figure 5-1 Figure 5-2 Figure 5-2 Figure 6-1 Figure 6-2 Figure 6-3 Figure 6-4 Figure 6-5 Figure 6-6 Figure 6-6 Figure 6-7 Figure 6-8 Figure 6-9 Figure 6-10 Figure 6-11 Figure 6-12 Figure 6-13 Figure 6-14 Figure 6-15 Figure 6-16
Rev 0, Apr/2007
KFS 576A Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-11 Waveform and Timing Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-13 Serial Data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-14 Display Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-15 Test Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4 KFS 576A Troubleshooting Flowchart. . . . . . . . . . . . . . . . . . . . . . . . 5-17 KFS 576A Troubleshooting Flowchart. . . . . . . . . . . . . . . . . . . . . . . . 5-19 Typical Bill of Material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-17 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-19 I/O Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-29 I/O Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-31 I/O Board Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-33 I/O Board Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-35 Microprocessor Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-41 Microprocessor Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-43 Microprocessor Board Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-45 Microprocessor Board Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-47 Switch Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-55 Switch Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-57 Switch Board Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-59 Driver Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-65 Driver Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-67 Driver Board Schematic. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-69
©Honeywell International Inc. Do not print without express permission of Honeywell.
LOF-1
KFS 576A
This Page Intentionally Left Blank
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
LOF-2
KFS 576A
SECTION 4 THEORY OF OPERATION 4.1 INTRODUCTION The KFS 576A is the cockpit-mounted Control Unit for the KXP 756 Transponder. It performs three main functions. First, that of converting switch inputs and information from the optional encoding altimeter into a serial data format and sending it to the transponder. Second, displaying the selected transponder code and mode of the transponder for the pilot via the gas-discharge display. Third, communicating status with an external unit via the 429 bus. 4.2 GENERAL CIRCUIT THEORY 4.2.1 CONTROL UNIT INPUTS The Control Unit signal inputs consist of the External Ident, Mode A/Mode B select, ten altitude (Mode C) inputs, 1/2 select, Master/Slave select, Emergency, Control Disable, External Standby and Reply input from the transponder. The External Ident input permits a remotely mounted switch to perform the same function as the Ident Button on the Control Unit. The Mode A/Mode B select input changes a bit in the serial data informing the transponder whether to reply to Mode A or Mode B interrogations. The altitude inputs are provided by an encoding altimeter. These inputs are serialized and transmitted to the transponder. The 1/2 select input determines the unit designation in a dual unit system. When the unit is designated a Master it initiates communications on the 429 bus. When it is a Slave it responds to interrogation on the 429 bus. When the Emergency input is active the code is replaced by 7700 when the cursor switch is held in for over 3 seconds. Activating Control Disable disables all the switch functions except the VFR Code recall. When the External Standby input is active the unit keeps the transponder in Standby mode. When the transponder is replying, it sends a signal to the Control Unit causing an “R” to be illuminated on the display. 4.2.2 FUNCTION SWITCH The switch is continuously rotatable in both directions and is used to select the desired mode of operation of the transponder. Nomenclature on the display indicates the position of the Function Switch.
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
4-1
KFS 576A
4.2.3 CODE SELECTOR SWITCH This switch is continuously rotatable in both directions and is used to change the transponder reply code. Momentarily depressing the switch knob changes the position of the cursor. The cursor points to the digit that will change when the Code Selector Switch is rotated. The cursor moves from left to right only. If the Code Selector Switch is held in continuously for approximately 3 seconds, the transponder code will change to the VFR code and the cursor will return to the leftmost position. 4.2.4 IDENT SWITCH Pressing the Ident Switch results in an ident pulse being sent to the transponder via the serial data line. This causes the transponder to transmit the SPI (Special Position Identification) pulse for approximately 23 seconds. The IDT nomenclature on the display, lights for approximately 23 seconds to indicate the transmission to the SPI pulse. The same action results when the External Ident input is activated. 4.2.5 OPERATING VOLTAGES All operating voltages, -26, +9.3 and +190V for the KFS 576A are externally supplied by the KXP 756 transponder. The +9.3V input is used to generate the +5V source by means of an I.C. regulator. The +190V is used to drive the gas discharge display. The -26V is regulated to -10V for the 429 circuitry. The KFS 576A is supplied in either a +5V or +28V bezel lighting version. 4.2.6 EEPROM An indicator without mechanical code selector switches is unable to “remember” its selected code when power is removed. To provide this feature an EEPROM is used. The Electrically Erasable Programmable Read Only Memory (EEPROM) “remembers” the transponder code when power is removed from the Control Unit. The code is automatically recalled from the EEPROM when power is applied to the Control Unit. 4.2.7 MULTIPLEX AND DISPLAY CIRCUITRY The KFS 576A uses a multiplexed gas-discharge display. The anodes of the display are energized sequentially. The data to be displayed on the cathodes is outputted synchronously with the clocking of the anodes. Each anode is energized for approximately 1 out of every 8msec. A photodetector activates the automatic dimming circuit and is used to adjust the display brightness in response to variations in ambient light levels.
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
4-2
KFS 576A
4.2.8 CLOCK, STROBE AND SERIAL DATA OUTPUTS As previously stated, all information inputted to the Control Unit is sent to the transponder in a serial data format. The Serial Data output contains all the information needed by the transponder to reply properly to an interrogation. The Strobe output indicates to the transponder the end of a valid sequence of serial data. The clock occurs only after a particular bit of data has stabilized on the Serial Data output causing the transponder to accept that particular bit of data. 4.2.9 TRANSPONDER SELECT SWITCH A Transponder Select Switch is installed on some versions of the KFS 576A and permits a single Control Unit to select one of two remote mounted transponders. This switch does not affect the operation of the indicator in any way other than determining which transponder is operational. 4.2.10 429 BUS The 429 Bus is used to communicate Control Unit status with external units. 4.3 DETAILED CIRCUIT THEORY The following is a detailed description of the KFS 576A circuit operation. The referenced schematics and timing diagrams should be used as an aid in understanding the theory. The following table lists component designators and the schematics on which they are found: Component Designations
Schematic
101-199 201-299 301-399 401-499
I/O Board Processor Board Driver Board Switch Board
4.3.1 POWER SUPPLY All operating voltages for the KFS 576A are externally provided (by the KXP 756 Transponder). 4.3.1.1 +5 VOLT REGULATOR I307 uses the +9.3 volt input to provide a +5 volt regulated output that is used to power the logic devices in the Control Unit. C311 provides filtering for the +5 volt line.
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
4-3
KFS 576A
4.3.1.2 HIGH VOLTAGE CURRENT LIMITER Q303 limits the current drawn from the +190 volt line to approximately 25mA. This provides protection for the anode and cathode drivers (I301, I302 and I303) and the gas discharge display in the event of a momentary short inside the display. 4.3.2 MICROPROCESSORS I202 and I203 are 8-bit, single chip microprocessors that control most of the operations in the Control Unit. A detailed description of the internal operation of the microprocessors or their interaction is not required for maintenance and is beyond the scope of this manual. Proper microprocessor operation is best determined by inputting of specific information and checking to see that the proper output is present. 4.3.2.1 ALTITUDE INPUTS Ten input lines from an encoding altimeter supply altitude information to the Control Unit. This data is then serialized and outputted to the transponder. The ten lines are multiplexed by I101 and I102. The multiplexed output from I101 and I102 is sent to microprocessor I202 pin 39 via J102 pin 16. 4.3.2.2 REPLY INPUT When the transponder replies to an interrogation, it sends a signal to the KFS 576A. As this signal falls below 2.5 volts it caused pin 1 of I204 to go low, which pulls pin 1 of I203 low. I203 subsequently causes the "R" nomenclature on the gas discharge to light indicating a transponder reply. A time delay in I203 causes the "R" to remain lit for about 250 msec after the Reply input returns to the high state. 4.3.2.3 CLOCK, STROBE AND SERIAL DATA Figure 4-2 Waveform and Timing Diagram shows typical clock, strobe and serial data waveforms. The clock and strobe lines are used by the transponder to decode the serial data information. Serial data is outputted from board 1 via board 2 to J5761-23. This data consists of 32 continuously repeating bits of information, each bit approximately 1 msec wide. The level of a particular bit, either high or low, represents some bit of information that must be sent from the KFS 576A to the transponder. For example, if the IDENT switch is pushed, the IDENT bit of serial data is low. Conversely, if the IDENT switch is not being pushed, the IDENT bit in the serial data is high. Figure 4-3 Serial Data shows the serial data and the information associated with each bit.
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
4-4
KFS 576A
Refer again to Figure 4-2 Waveform and Timing Diagram and notice the time relationship between the clock, strobe and serial data signals. The clock signal occurs only after the data bit has stabilized at which time the clock goes high. The data bit level during the rising edge determines what value of data will be "seen" by the transponder. After 32 bits of serial data have been transmitted, the strobe occurs which indicates the end of a 32 bit segment of data and the beginning of a new 32 bit segment. Q201, Q202, and Q203 invert and level shift the DATA STROBE, CLOCK BUS, and DATA BUS lines from I203 respectively. The output from Q201 is P201 pin 6, Q202 is P201 pin 13, and Q203 is P202 pin 19. 4.3.2.4 MODE A/B SELECT Grounding pin 9 of J5761 causes the A/B bit of the serial data to go low. This results in the transponder replying only to Mode B and Mode C interrogations. When pin 9 of J5761 is open to the A/B bit is high and the transponder replies only to Mode A and Mode C interrogations. Without a transponder, this bit can be checked by observing the serial data while pin 9 of J5761 is grounded and opened. 4.3.2.5 429 BUS When 429 data is received on J5762-1 and 2 it is buffered by I103A. The output of I103A is level shifted by R141 and R213. If the signal level is greater than 7.6 volts I206B pulls TP207 low interrupting the microprocessor I202. If the signal level is less than 3 volts I207A pulls TP207 low. When TP207 goes low TP208 reflects the state of the 429 data bit received so the microprocessor can read it on I202-1. When the microprocessor I202 transmits data on the 429 bus it first turns on the 429 bus drivers by pulling I202-38 low. The 429 bus drivers are composed of Q107 thru Q110 and associated components which supply +5, -10, and +9.3 volts to drive the 429 data bus components. Data is outputted on I202-33, 34. These two data lines are inverted by Q105 and Q106. These two signals are differentially amplified by I104A and I105A. The output of I105A is the inverse of I104A. When I202-33 and 34 are both high, J5762-1 and 2 are both 0 volts. When I202-33 is high and I202-34 is low J5762-1 is -5 volts and J5762-2 is +5 volts. When I202-33 is low and I202-34 is high J5762-1 is +5 volts and J5762-2 is -5 volts. When the microprocessor is finished transmitting a 32 bit word it turns off the 429 bus drivers by pulling I202-38 high.
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
4-5
KFS 576A
4.3.2.6 EEPROM I201 is an Electrically Erasable Programmable Read Only Memory (EEPROM). Data stored in memory I201 can only be erased electrically and remains stored even when power is removed. I201 has a RAM space that is bit for bit mapped over the EEPROM. Pin 11 controls reading and writing to the device RAM. Pin 9 of the EEPROM is the store line. When I201-9 goes low the contents of the RAM are stored in EEPROM. When power is applied to the control unit R212 and C201 hold I201-10 low for a short time after the 5 volt line is valid. This results in a power on recall from EEPROM to RAM of the last code that was programmed so the microprocessor can read it. To prevent the EEPROM from being needlessly updated, the microprocessors wait approximately 3 seconds after a digit has changed and if another digit does not change within that time, it updates the EEPROM with the new code. 4.3.2.7 MICROPROCESSOR RESET Pin 4 of both I202 and I203 are the reset inputs for the microprocessors and are used when power to I202 and I203 are interrupted. Pin 4 of I202 and I203 are held at +5V during normal operation. When a power interruption occurs, I202-4 and I203-4 must be brought to ground before power is reapplied. Pin 4 must then slowly rise to +5V. I204B senses a drop in the 9.3 volt supply and pulls pin 4 of I202 and I203 low. When power is reapplied, I204B pulls I202-4 and I203-4 low and then allows them to slowly rise to +5 volts through an external capacitor C208. 4.3.2.8 SWITCH INPUTS Pins 21, 22, 23 and 24 of I203 are the inputs to the microprocessor from the Function selector, Code selector, Ident, and Cursor switch. The DATA SEL and DATA SEL signals are complements of each other. Only one of the two signals can be low at a time. This enables the use of only four pins of I203 to input eight different sources of information through a multiplexing scheme. The Code selector switch is connected to E401 DATA SEL and the Function Switch to E402 DATA SEL. I203 alternately changes pin 17 from low, to check the status of the FUNCTION and IDENT SWITCH to high, to check the status of the CODE and CURSOR switches. The status of each switch is read by setting the appropriate DATA SEL line to low and checking the status of pins 21, 22, 23, and 24. I203 Pins 21 thru 23 are connected to the FUNCTION/CODE switches and I203 Pin 24 is the IDENT/CURSOR line. I203 interprets a low input to pin 21, 22, 23, or 24 during the time DATA SEL is low as an input from the Function and Ident Switches. A low on pins 21, 22, 23 or 24 of I203 during the time DATA SEL is low will be interpreted as an input from the Code Selector and Cursor Switches.
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
4-6
KFS 576A
4.3.3 DISPLAY CIRCUITRY The KFS 576A display circuitry consists of a gas discharge display and associated multiplexing and driving circuitry. This circuit sequentially fires the eight anodes and energizes the proper cathodes. Refer to Figure 4-4 Display Timing Diagram for display timing information. In addition, a programming current proportional to the ambient light level is supplied to the cathode drivers to provide automatic dimming of the gas discharge display. To insure proper display functioning under all ambient light and temperature conditions, two keep-alive anodes inside the gas discharge display (DS103) are continuously ionized. The keep-alive anodes connect to +190 volts through R401 and R402 and the keep-alive cathodes connect to ground through R323 and R324. 4.3.3.1 ANODE AND CATHODE DRIVERS The gas discharge display consists of 8 anodes and 13 cathode buses. Four of the anodes are associated with the 7-segment digits and their cursors. The remaining four anodes are used with the nomenclature. Each cathode bus is connected to the particular segment of a digit, a cursor, or one letter in the nomenclature. The corresponding segments of each digit are wired together to form the "a", "b", "c", "d", "e", "f" and "g" buses. For example, the "a" cathode bus (pin 11 of DS103) is connected to the top segment of all four digits. All of the cursors are wired together to form the "h" cathode bus. Cathode buses "i”, "j", "k", "l" and "m" are associated with letters in the nomenclature and they are formed in a similar manner. There is approximately +100 volts on the anodes of the display when they are not being fired, while the cathodes are approximately +70 volts. This +30 volt differential is not enough to ionize the gas and illuminate a display cathode segment. The corresponding anode must be pulled high (about +190 volts) by I302 and the cathode must be pulled low (about +15 volts) by I301 or I303. Once the segment is ionized the cathode voltage increases to about +35 volts and the resulting +155 volts between the anode and cathode is sufficient to sustain the ionization and illuminate a cathode segment. The anodes of the display are driven by I302 and fired sequentially in the following order: 2, 8, 3, 6, 4, 1, 5, 7. A high on an input of I302 raises the corresponding output from about +100 volts to about +190 volts. Anode driver I302 is driven by I304, an eight bit Johnson (ring) counter.
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
4-7
KFS 576A
Only one output of I304 is high at a time which results in only one anode being energized at a time. An output of I304 goes high on the rising edge of the clock bus line and remains high until the next rising edge at which time the next anode in the sequence is energized. The anode voltage, which is applied to I302-10, is turned on and off with the cathode by Q304 and Q305. As a result, if a segment is to be energized, the anode and cathode voltages are switched on and off together. Like the cathode voltage, the amount of time the anode voltage remains is dependent on the ambient light level. A Multiplex SYNC signal, P301-6, synchronizes the output of I304 with the data present on the cathode buses. This signal forces anode #2 to go high in the event I304 is falsely triggered and anode #2 is not already high, thus keeping the anode synchronous with the cathode data. The cathode firing sequence is such that a cathode associated with a digit is energized followed by an anode associated with a nomenclature in a continuous manner. I303 drives the nomenclature cathode buses while I301 drives the digit cathode buses. A high on the input of I303 pulls the corresponding output from about +70 volts to about +10 volts. This will cause ionization of the gas if the associated anode is energized at the same time. Some inputs and outputs of I303 are paralleled to provide increased driving current for the larger cathode segments in the nomenclature. I301 functions similar to I303 except that it contains a BCD to 7-segment decoder. Inputs D1, D2, D3, D4 and D8 contain bits 1, 2, 4 and 8 of the Binary Coded Decimal digit that is to be displayed. The decoder determines which cathode buses should be pulled low to display the digit. For example, if the digit "3" (binary 0011) is to be displayed as the leftmost digit, pins 4 and 5 of I301 are low while pins 2 and 3 of I301 are high. The decoder interprets this input as a three and pulls cathodes "a", "b", "c", "d" and "g" low. If anode #2 is energized a three will illuminate as the leftmost digit. The cursors in the display are energized by a low on I301-10 which pulls the "h" cathode bus low. Note that this input is different from all the others since a low signal pulls the cathode bus low. Q304 and Q305 form a voltage divider that supplies approximately +95 volts to the driving circuitry. 4.3.3.2 AUTOMATIC DIMMING The brightness of the gas discharge changes in response to varying ambient light as sensed by photodetector V401. Dimming is accomplished by varying both the duty cycle and the amplitude of the cathode driving current. A square wave present at TP302 varies its duty cycle as a function of ambient light. This is accomplished by means of a one-shot (I305), a constant current source (I306B) and a photodetector (V401). The current output of I306B decreases as the increasing ambient light level lowers the resistance of V401. This variable current varies the rate of charge of C308. The time constant of I305 is determined by the rate of charge of this capacitor. The minimum time constant is approximately 80 usec and can be adjusted by R327. Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
4-8
KFS 576A
As ambient light increases the pulse width at TP302 continues to increase. This pulse begins when the clock bus line on I305-2 and 4 goes high and triggers the one-shot and ends at the time determined by the rate of charge of C308. The maximum pulse width can be no longer than the time between the rising and falling edge of the clock bus line, approximately 1msec. This is because a low on I305-2 and 4 forces I305 to reset causing the output of I305 pin 3 change from high to low. The output of I305 is filtered by R314 and C301 to form a DC voltage proportional to the duty cycle of the square wave. This DC voltage is applied to I306A which is used as a voltage-to-current converter. The output of I306A is a current that is proportional to the voltage on C301. CR302 shunts this current to ground when the signal at TP302 is low resulting in a cathode driving current that varies in amplitude and duty cycle. R310 limits this current to the value required by cathode drivers I301 and I306. Each output of I301 and I303 acts as a constant current source. This source current is proportional to the current applied to pin 1 of I301 and I303. Since the programming current at pin 1 of the I.C.'s varies in amplitude and duration the cathode current is also varied and the brightness of the gas discharge display changes in response to ambient light level. A line from I203 microprocessor pin 17 is outputted to I205A inverter which is sent to P301 pin 7 “DIM 1” and I205A which inverts the signal and outputs it to P301 pin 11 “DIM 2”. DIM 2 is the inverse of the DIM 1. DIM 1 switches Q301 on allowing I301 to source current while DIM 2 switches Q302 off so I303 cannot source current. On the next falling edge of DATA SEL line I203 pin 17 the signals are inverted and I303 sources current and I301 does not.
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
4-9
KFS 576A
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
4-10
KFS 576A
Figure 4-1 KFS 576A Block Diagram (Dwg No 696-06837-0000 Rev 0) Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
4-11
KFS 576A
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
4-12
KFS 576A
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
4-12
KFS 576A
KFS 576A
Figure 4-2 Waveform and Timing Diagram
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
4-13
KFS 576A
Figure 4-3 Serial Data (Dwg No 696-06838-0000 Rev 0) Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
4-14
KFS 576A
Figure 4-4 Display Timing Diagram (Dwg No 696-06828-0001 Rev 0) Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
4-15
KFS 576A
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
4-16
KFS 576A
SECTION 5 MAINTENANCE 5.1 GENERAL INFORMATION This section contains test, alignment, inspection, cleaning, disassembly/assembly and troubleshooting procedures for the KFS 576A Transponder Control Unit. 5.2 TEST AND ALIGNMENT The preferred method of testing the KFS 576A Transponder Control Unit is using either an APPLE //e or an APPLE ][ PLUS or equivalent personal computer with a disk drive, 48K or memory and a monitor. The following procedure describes how to prepare the KFS 576A for testing. Refer to the test setup illustration in Figure 5-1 Test Setup. 5.2.1 TEST EQUIPMENT REQUIRED A. Power supply: +28 VDC @ 5A Sorensen PTM 28-6.0 or equivalent B. Oscilloscope: Tektronics 465 or equivalent C. Digital voltmeter: Fluke 8000A or equivalent D. Apple test system: 1. Apple //e or Apple ][ plus with 48 K memory or equivalent. 2. Apple Disk ][ and controller card, 5 1/4 inch or equivalent. 3. Video monitor. E. KCT 110 Test Set, PN 050-02260-0010, which contains: 1. KCA 110 Test set Adapter, PN 071-05084-0000. 2. KFS 564/A Test disk, PN 222-00002-0000. 3. KFS 586/A Test disk, PN 222-00003-0000. 4. KFS 579/A Test disk, PN 222-00004-0000. 5. KFS 576/A Test disk, PN 222-00005-0000. 6. KFS 598/A Test disk, PN 222-00006-0000.
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
5-1
KFS 576A
F. Async Card Kit, PN 050-02605-0000, which contains: 1. Async card, PN 200-07157-0000. 2. Async cable P1, PN 155-05664-0016. 3. Async cable P2, PN 155-05664-0006. 4. Async cable P3, PN 155-05664-0012. G. Sync Card Kit, PN 050-02606-0000, which contains: 1. Sync card, PN 200-07164-0000. 2. Sync cable P2, PN 155-05664-0007. 3. Sync cable P3, PN 155-05664-0017. 5.2.2 DESCRIPTION OF KFS 576A TEST PROGRAM Testing of the KFS 576A requires the ability to receive and display the King serial data messages which are used to set up the mode of the KXP 756 transponder. It is also necessary to send a selected, as well as display a received, ARINC 429 serial data message. The ARINC 429 serial data message is used to communicate between master and slave KFS 576A’s in a tandem installation or a KFS 576A and a KNS 660 system for frequency management. The KCT 110 computer test system used in conjunction with an Apple or Apple equivalent computer system, as described in section 5.2.1. will provide all of the necessary serial interface and control function interface to the KFS 576A . The KCT 110 consists of two PC boards which will be inserted in the appropriate card slots of the computer. The KCA 110 interface box contains break out of necessary test points, four cables which connect the KFS 576A and the KCA 110 interface box to the computer, and a floppy disk containing the test program. The KCA 110 will supply power to the control unit. The KFS 576A test program is set up to follow the test procedures and test data sheet in section 5.2.4. of this manual. The test program will ask for the specific part number of the control unit to be tested, so that a menu of tests can be displayed on the screen. Once the menu is displayed you may choose to step through in sequence, filling out a test data sheet and completing a final test data sheet, or go directly to a specific test in an attempt to verify a complaint or performance of a unit function. The last step on the menu, unit status, is not part of the final test procedure. The unit status portion of the program displays all functions except auto dim override and ARINC 429. The unit status will be valuable for trouble-shooting the commonly used functions of a KFS 576A.
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
5-2
KFS 576A
5.2.3 ALIGNMENT A. Display dimming is the only adjustment necessary for the KFS 576A. B. To adjust the brightness, connect an oscilloscope to TP 302. Cover the photodetector with an opaque material. A finger is not opaque and will not block sufficient light to correctly set the brightness. Adjust R 327 until the pulse width is 80us wide. Remove opaque material from detector. 5.2.4 FINAL TEST The following tests (in the KFS 576A Test Program) should be run to determine if the KFS 576A is operating properly. If it is not, refer to the alignment and troubleshooting sections of this manual for guidance in locating the problem. TEST SETUP 1. The bench test setup should be connected as shown in Figure 5-1 Test Setup. 2. Connect the monitor and disk drive to the computer per the instructions in the owners manual. 3. Confirm that the computer system is operating properly. Refer to owners manual. 4. Make sure power is turned off to both the KFS 576A and the APPLE computer. 5. Remove the cover on the APPLE computer and insert the sync card in any slot except 0 (5 is preferred), and the async card in any slot except 0 (7 is preferred). 6. Connect the ribbon cables from the King sync card to the KCA 110 interface box and the ribbon cable from the King async card to the KCA 110 interface box and put the cover back on computer. 7. Connect the KFS 576A interface harness to the Interface Box and the KFS 576A. 8. Insert the diskette containing the KFS 576A Test Program into the disk drive and turn on computer. The top menu will then appear on the monitor. Select the KFS 576A Test Program. The test program requires about 30 seconds to load. 9. Apply +28 VDC to the interface box, then turn on the control unit (if equipped with an ON/OFF switch). At this time the KFS 576A should have all voltages necessary to operate and should come on. 10.Follow the instructions displayed on the monitor and any supplemental instructions in the corresponding paragraphs in this section. Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
5-3
KFS 576A
Figure 5-1 Test Setup NOTE:1.The scope.DVM.and audio gen. Connect to test points and test connectors on the front of the KCA 110 during testing per the final test procedures. During alignment the scope is used to monitor a test point inside the control unit. 2.The sync card is inserted into any slot except 0, however 5 is preferred. The async card is inserted into any slot except 0, however 7 is preferred. The KCA 110 cables reach through the rear of the computer to the cards. NOTE The slot 0 applies only to the Apple ][ plus. 3. The KCA 110 cable #4 connects the KFS control unit to the KCA 110 via P1014. Cable 4 has connectors for all of the control units. Observe the connector markings and connect the appropriate connector to the unit to be tested. Do not connect more than one control unit at a time. 4. Unless otherwise indicated, when instructions are given on the Apple screen or in the Maintenance manual to press a key it is implied that the key stroke is momentary. If the key is held down the function may be repeated. Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
5-4
KFS 576A
5.2.4.1 ON/OFF A. 071-1276-19/20/21/22: If unit is not equipped with an ON/OFF switch, verify that the display of the unit is illuminated when power is applied to the KCA 110. B. 071-1276-08/09/10/11/18: Turn the On/Off knob from the OFF position to the ON position and verify that the display of the unit is illuminated when power is applied to the KCA 110. C. 071-1276-13/14/15/16: Turn the 1/OFF/2 knob from the OFF position to the 1 position. Verify that the display of the unit is illuminated in the 1 position and not illuminated in the OFF position. Turn the 1/OFF/2 knob to the 2 position. Verify that the display is illuminated and that TP11 ON 1 is high. D. 071-1276-23/24/25/26: Turn the 1/2 knob to the 1 position. Verify that the display of the unit is illuminated. Turn the 1/2 knob to the 2 position. Verify that the display is illuminated and that TP11 ON 1 is high. 5.2.4.2 DISPLAY A. Verify that the display does not flicker in a dark environment. B. All segments shall be of uniform brightness with no arcing between segments. C. Use the selector switch (S1) on the KCA 110 to verify that the lighting is working correctly. 5.2.4.3 FLIGHT LEVEL (FL) To test Flight Level (FL) ground External Standby (J5761 pin 17). This should place the unit in SBY mode. Turn the function switch clockwise to view Flight Level. Verify that the Flight Level on the control head display is the same as the Flight Level selected on the Apple screen. Use the <- and -> cursor keys to increment/decrement the Flight Levels on Apple.
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
5-5
KFS 576A
1. A zero indicates that the corresponding pin of J5761 is open; a one indicates that the pin is shorted to ground. 2. Altitude is displayed only in TEST mode and Flight Level mode. 5.2.4.4 IDENT Verify that when the IDT button is pushed or the external ident line (J 5761 pin 21) is grounded IDT should light in the lower right corner of the control head display and stay lit for 23 ±4 seconds. NOTE: IDT will not light in standby mode, unless otherwise desired leave External Ident in the non-active state. 5.2.4.5 CODE SELECTOR SWITCH NOTE: There should be a change in code for every increment or decrement. A. Verify that clockwise rotation increments the digit above the cursor in the control head display. B. Verify that counter-clockwise rotation decrements the digit above the cursor in the control head display. C. Digits should rollover from 7 to 0 and roll under from 0 to 7. NOTE: There should be a change in cursor position each time the cursor switch is pushed. D. When the cursor switch is pushed the control head display cursor should move from left to right. If the cursor is pointing to the right most digit when the switch is pushed the cursor should move to the left most digit. The cursor will remain under a digit for approximately 5 seconds and if the code selector switch is not rotated during that 5 second period the cursor will return to the leftmost digit and the new code is transmitted from the RT. Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
5-6
KFS 576A
5.2.4.6 EMERGENCY Verify that when Emergency (J5762 pin 4) is grounded the channeling code should change to 7700 when the cursor is held in for at least 3 seconds. NOTE: Unless otherwise desired leave emergency in the non-active state. 5.2.4.7 REPLY Verify that when Reply (J5761 pin 11) is grounded the “R” in the upper left corner should light. NOTE: Unless otherwise desired leave reply in the non-active state. 5.2.4.8 DIMMING A. Verify that the display dims evenly in a dark environment. B. Verify that grounding automatic dimmer override (J5761 pin 25) disables dimming from the photo-cell and the display goes to maximum brightness. 5.2.4.9 EXTERNAL STANDBY When the External Standby (J5761 pin 17) is grounded the unit should go to standby mode. When the line is ungrounded the unit should return to the mode it was in prior to activating the line. NOTE: Unless otherwise desired leave external standby in the non-active state. 5.2.4.10 CONTROL DISABLE Verify that the when Control Disable (J5762 pin 5) is grounded, the cursor is extinguished. NOTE: Before going on to another step leave control disable not active. 5.2.4.11 NON VOLATILE MEMORY A. Change Transponder Code. B. Observe display. C. Wait at least 5 seconds. D. Remove power from the unit.
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
5-7
KFS 576A
E. Reapply power to the unit. F. Verify that display is the same as observed in step B. 5.2.4.12 CHANNELING NOTE: The information on the Apple screen is a display of what is on the serial synthesizer bus. A. Verify that the Xpond data bus transmits the serial data from the control head display to the Apple screen. Refer to the table below for appropriate voltage levels for the Xpond Clock TP 3. Xpond Data TP 4, Xpond Strobe TP 5 lines. XPOND CLK TP3
XPOND DATA TP 4
XPOND TP 5
VOLTAGE HIGH
8.0V min
10.0V max
VOLTAGE LOW
0.0V min
0.5V max
5.2.4.13 429 I/O A. UNIT ONE 1. Place control head in Unit No. 1 and Slave modes. Verify that there is no data present on TP 1 (data A) and TP 2 (data B). 2. Send a frequency from the apple key board to the control head. Verify that the control head display duplicates the key board. (Note: 429 data will appear in this test) B. UNIT TWO 1. Place control head in Unit No. 2. and Master modes. Verify that the voltages between the data line A, TP 1 and B, TP 2 are. VOLTAGE HIGH
9.0V MIN
11.0V MAX
VOLTAGE NULL
-0.5V MIN
0.5V MAX
VOLTAGE LOW
-11.0V MIN
-9.0V MAX
NOTE: Place TP 1 on channel 1 of the Oscilloscope. Place TP 2 on channel 2 of the Oscilloscope. Invert channel 2 and add the two channels.
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
5-8
KFS 576A
5.2.4.14 VFR CODE To program the VFR code: Rotate the function selector knob to standby, select the VFR code as required, press the IDT and Cursor buttons simultaneously. The displayed code should be stored as the VFR code. To select the VFR code: When the cursor switch is held in for at least 3 seconds, the display code should be replaced with the last VFR code programmed. 5.2.4.15 UNIT STATUS This test is only intended to be used as a troubleshooting aid.
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
5-9
KFS 576A
5.2.4.16 FINAL TEST DATA SHEET NOTE: The term "OK" indicates that particular function is operating properly. 1.
On/Off
2.
Display
3.
4.
5.
OK
a.
Display
OK
b.
Lighting
OK
Flight Level Display matches Apple screen
OK
a.
IDENT button
OK
b.
External IDENT
OK
Ident
Code selector switch a.
Clockwise rotation
OK
b.
Counter-clockwise rotation
OK
c.
Rollover
OK
d.
Cursor switch
OK
6.
Emergency
(7700)OK
7.
Reply “R” lit
OK
8.
Dimming
9.
a.
Display dims evenly
OK
b.
Pulse width 80us
OK see para. 5.2.3 alignment
c.
Display goes to max bright
OK
d.
Photo-cell is disabled
OK
External Standby
Rev 0, Apr/2007
OK
©Honeywell International Inc. Do not print without express permission of Honeywell.
5-10
KFS 576A
10.
Control disable a.
Cursor not lit
11
Memory
12.
Channeling a.
OK
Control head matches Apple
OK
1.
Xpond clock TP 3
OK logic high greater than 8v
Xpond clock TP 3
OK logic low less than .5v
Xpond Data TP 4
OK logic high greater than 8v
Xpond Data TP 4
OK logic low less than .5v
Xpond strobe TP 5
OK logic high greater than 8v
Xpond strobe TP 5
OK logic low less than .5v
2.
3.
13.
429 I/O a.
UNIT ONE 1. 2.
b.
Unit 1, Slave. No data on A and B
OK
Apple keyboard changes display
OK
UNIT TWO 1.
2. 14.
OK
Unit 2, Master
OK
Voltage between A and B
OK logic high greater than +9V
Voltage between A and B logic null less than +.5V
OK
Voltage between A and B logic low less than -9V
OK
Apple screen matches control head
OK
VFR code a.
Stores VFR code
OK
b.
Selects VFR code
OK
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
5-11
KFS 576A
5.3 OVERHAUL 5.3.1 VISUAL INSPECTION This section contains instructions to assist in determining, by inspection, the condition of the KFS 576A assemblies. Defects resulting from wear, physical damage, deterioration or other causes can be found by these inspection procedures. To aid inspection, detailed procedures are arranged in alphabetical order. A. Capacitors, Fixed Inspect capacitors for case damage, body damage, and cracked, broken, or charred insulation. Check for loose, broken, or corroded terminal studs, lugs, or leads. Inspect for loose, broken, or improperly soldered connections. B. Capacitors, Variable Inspect trimmers for chipped and cracked bodies, damaged dielectrics and damaged contacts. C. Chassis Inspect the chassis for deformation, dents, punctures, badly worn surfaces, damaged connectors, damaged fastener devices, loose or missing hardware, component corrosion, and damage to the finish. D. Connectors Inspect connectors for broken parts, deformed shells or clamps, and other irregularities. Inspect for cracked or broken insulation and for contacts that are broken, deformed or out of alignment. Also, check for corroded or damaged plating on contacts and for loose, improperly soldered, broken, or corroded terminal connections. E. Covers and Shields Inspect covers and shields for punctures, deep dents, and badly worn surfaces. Also, check for damaged fastener devices, corrosion and damage to finish. F. Fuse and Clips Inspect for blown fuse and check clips for loose or corroded connections.
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
5-12
KFS 576A
G. Insulators Inspect insulators for evidence of damage, such as broken or chipped edges, burned areas, and presence of foreign matter. H. Jacks Inspect all jacks for corrosion, rust, deformations, loose or broken parts, cracked insulation, bad contacts, or other irregularities. I. Potentiometers Inspect all potentiometers for evidence of damage or loose terminals, cracked insulation or other irregularities. J. Resistors, Fixed Inspect the fixed resistors for cracked, broken, blistered, or charred bodies and loose, broken, or improperly soldered connections. K. RF Coils Inspect all RF coils for broken leads, loose mountings, and loose, improperly soldered, or broken terminal connections. Check for crushed, scratched, cut or charred windings. Inspect the windings, leads, terminals and connections for corrosion or physical damage. Check for physical damage to forms and tuning slug adjustment screws. L. Terminal Connections Soldered 1. Inspect for cold-soldered or rosin joints. These joints present a porous or dull, rough appearance. Check for strength of bond using the points of a tool. 2. Examine the terminals for excess solder, protrusions from a joint, pieces adhering to adjacent insulation, and particles lodged between joints, conductors, or other components. 3. Inspect for insufficient solder and unsoldered strands of wire protruding from the conductor at terminal. Check for insulation that is stripped back too far from the terminal. 4. Inspect for corrosion at the terminal.
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
5-13
KFS 576A
M. Transformers 1. Inspect for signs of excessive heating, physical damage to case, cracked or broken insulation, and other abnormal conditions. 2. Inspect for corroded, poorly soldered, or loose connecting leads or terminals. N. Wiring/Coaxial Cable Inspect open and laced wiring of the chassis, subassembly chassis and parts of equipment for breaks in insulation, conductor breaks, cut or broken lacing and improper dress in relation to adjacent wiring or chassis. 5.3.3 CLEANING A. Using a clean, lint-free cloth lightly moistened with a regular cleaning detergent, remove the foreign matter from the equipment case and unit front panels. Wipe dry using a clean, dry, lint-free cloth. B. Using a hand controlled dry air jet (not more than 15psi), blow the dust from inaccessible areas. Care should be taken to prevent damage by the airblast. C. Clean the receptacles and plugs with a hand controlled dry air jet (not more than 25psi), and a clean, lint-free cloth lightly moistened with an approved cleaning solvent. Wipe dry with a clean, dry, lint-free cloth. 5.3.3 REPAIR This section describes the procedure along with any special techniques for replacing damaged or defective components. A. Connectors When replacing a connector, refer to the appropriate PC board assembly drawing and follow notes to insure correct mounting and mating of each connector. B. Crystal The use of other than a King approved crystal is considered an unauthorized modification. C. Diodes Diodes used are silicon and germanium; use long nose pliers as a heat sink under normal soldering conditions. Note the diode polarity before removal.
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
5-14
KFS 576A
D. Wiring/Coaxial Cables When repairing a wire that has broken from its terminal, remove all old solder and pieces of wire from the terminal, restrip the wire to the necessary length and resolder the wire to the terminal. Replace the damaged wire or coax with one of the same type, size and length. 5.3.4 DISASSEMBLY Refer to Figure 6-1. 5.3.4.1 COVER REMOVAL (047-05021-0002) A. Remove the two screws at the back of the unit cover, and the two screws which are located on the top and bottom of the unit. Remove unit cover. 5.3.4.2 MICROPROCESSOR BOARD REMOVAL (200-6580-XX) A. Remove the two screws at the rear and front of the Microprocessor board. B. Carefully remove the Board by sliding the board outward from the connector pins till the board is disconnected from the I/O board (200-06579-XXXX) connector pins. 5.3.4.3 FRONT COVER/SWITCH BOARD REMOVAL (088-01166-XXXX/ 200-06589-XXXX) A. Remove front knobs from unit. B. Remove the four screws that hold the front cover to the unit, remove front cover. C. Remove display (037-00083-0000) from board. D. Disconnect switch (200-06579-XXXX).
board
harness
connector
from
the
I/O
board
E. Remove the three screws holding the Display board to the unit. F. The switch board can then be removed by sliding the board forward till the driver board pins and the switch board connector are disconnected from each other.
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
5-15
KFS 576A
5.3.4.4 DRIVER BOARD REMOVAL (200-06626-XXXX) A. Remove the rear two screws and the front three screws. B. The board can now be pulled away from the center mounted I/O board (200-06579-XXXX), being careful not to damage the I/O board (200-06579-XXXX) connector pins or the connector on the driver board. 5.3.4.5 ASSEMBLY A. To reassemble the unit, reverse disassembly procedures. 5.4 TROUBLESHOOTING To troubleshoot the KFS 576A consult the schematics for waveform and voltage data, and refer to the troubleshooting flowchart in Figure 5-2 KFS 576A Troubleshooting Flowchart for troubleshooting information. The following voltages should be checked before troubleshooting is attempted. A. J5761-7
+190V
B. J5761-10
+9.3V
C. I106-3
-26V
D. J103-7
Lighting +28VDC or +5VDC as appropriate
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
5-16
KFS 576A
Figure 5-2 KFS 576A Troubleshooting Flowchart (Dwg No 696-02376-0000 Rev 0) (Sheet 1 of 2) Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
5-17
KFS 576A
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
5-18
KFS 576A
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
5-18
KFS 576A
Figure 5-2 KFS 576A Troubleshooting Flowchart (Dwg No 696-02376-0000 Rev 0) (Sheet 2 of 2) Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
5-19
KFS 576A
Figure 5-2 KFS 576A Troubleshooting Flowchart (Dwg No 696-02376-0000 Rev 0) (Sheet 2 of 2) Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
5-19
KFS 576A
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
5-20
KFS 576A
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
5-20
KFS 576A
SECTION 6 ILLUSTRATED PARTS LIST 6.1 INTRODUCTION This Illustrated Parts List (IPL) provides for the proper identification of replacement parts. Individual Bills of Material (BOM) within this IPL are arranged in numerical order by BOM number. Each BOM is followed by the Assembly Drawing and Schematic Diagram for that assembly. Parts identified in this IPL by Honeywell Part Number meet design specifications for this equipment and are the recommended replacement parts. Warranty information concerning Honeywell replacement parts are contained in Service Memo #1, P/N 600-08001-XXXX. 6.2 BILL OF MATERIAL DESCRIPTION This section describes the various items that appear on the Bills of Material. A sample BOM is included in this section as Figure 6-1 Typical Bill of Material . NOTE: To facilitate a common Part Number System between ATAD and GAAD, the existing 9-digit numbering system is being expanded to 12 digits by the addition of 3 zeros. Add one zero to the center set and two zeros to the dash number
KFS 576A
SECTION 6 ILLUSTRATED PARTS LIST 6.1 INTRODUCTION This Illustrated Parts List (IPL) provides for the proper identification of replacement parts. Individual Bills of Material (BOM) within this IPL are arranged in numerical order by BOM number. Each BOM is followed by the Assembly Drawing and Schematic Diagram for that assembly. Parts identified in this IPL by Honeywell Part Number meet design specifications for this equipment and are the recommended replacement parts. Warranty information concerning Honeywell replacement parts are contained in Service Memo #1, P/N 600-08001-XXXX. 6.2 BILL OF MATERIAL DESCRIPTION This section describes the various items that appear on the Bills of Material. A sample BOM is included in this section as Figure 6-1 Typical Bill of Material . NOTE: To facilitate a common Part Number System between ATAD and GAAD, the existing 9-digit numbering system is being expanded to 12 digits by the addition of 3 zeros. Add one zero to the center set and two zeros to the dash number (XXX-0XXX-00XX). Parts or documents represented either by the existing 9-digit or expanded 12-digit part number are identical and interchangeable. A. BOM Number The Bill of Material Number appears at the top of the BOM as a 9-digit number which is also the Honeywell Part Number for the assembly. The BOM Number is followed by the assembly description and the revision level of the BOM. B. Symbol Column This column contains the Reference Designators of the electrical components of the assembly. Mechanical parts are not assigned Reference Designators. The Reference Designator consists of a letter abbreviation which indicates the type of component followed by the number assigned to that part (C101, Q101, etc). Common Reference Designator abbreviations are listed below.
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-1
KFS 576A
C
Capacitor
P
Plug
CJ
Circuit Jumper
R
Resistor
CR
Diode
S
Switch
DS
Lamp
T
Transformer
F
Fuse
TP
Test Point
FL
Filter
U
Resistor/Capacitor Network
I
Integrated Circuit
V
Photocell/tube
J
Fixed Connector
WG
Waveguide
L
Inductor
Y
Crystal
Q
Transistor
C. Part Number Column This column contains the King Part Number for each part. Special purpose 999-9999-XX series part numbers may appear in the BOM and are described below. 1. CR401
999-9999-99
DO NOT USE
The component designator CR401 has been previously used on the assembly and then deleted; therefore it cannot be reassigned. 2. CR401
999-9999-98
NOT USED
The component designator CR401 is available for future assignment and is not presently a part of the PC board/Final assembly. 3. CR401
999-9999-97
SEE NEXT ASSEMBLY
The component designator CR401 is used as part of the electrical circuit assembly but because of assembly or testing requirements may be part of another assembly. 4. CR401
999-9999-96
RESERVED
The component designator CR 401 is reserved for future usage.
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-2
KFS 576A
D. Description Column This column contains the description of each part in the assembly. Common abbreviations which may appear in this column are listed below.
AL
Aluminum
PC
Polycarbonate
BIFLR
Bifilar
PF
Precision Film
BOM
Bill of Material
PP
Paper
CC
Carbon Composite
PS
Polystrene
CF
Carbon Film
QW
Quarter Watt
CH
Choke
RES
Resistor
CAP
Capacitor
S
Silicon
CAP CR
Ceramic
SCR
Screw
DC
Disk Ceramic
SM
Silver Mica
DIO
Diode
STDF
Standoff
EL
Electrolytic
SW
Switch
FC
Fixed Composition
TERM
Terminal
FERR
Ferrite
TN
Tantalum
FLTR
Filter
TST PT
Test Point
FT
Feedthru
TW
Tenth Watt
HV
High Voltage
VA
Variable
HW
Half Watt
WW
Wire Wound
IC
Integrated Circuit
XFMR
Transformer
MC
Monolithic Ceramic
XSTR
Transistor
MY
Mylar
XTAL
Crystal
E. Assembly (A) Column An "A" in this column indicates that the part indicated is an assembly. If the PN and description reads "200-XXXXX-0099 COMMON BOM" the parts for that assembly are included in the same BOM. The parts breakdown for an assembly with any other PN will be found in the BOM with the same number.
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-3
KFS 576A
F. Unit of Measure (UM) Column This column indicates the Unit of Measure for each part. Common abbreviations found in this column are listed below.
EA Each FT Foot AR As Required G. Quantity and Version Columns Individual versions of an assembly are identified by the last two digits of the PN. Part quantities for each version will be indicated under headings numbered 0000 through 0099 as required. The parts indicated in the 0099 Column are common to all other versions of the assembly and are considered the Common Bill of Material for the assembly.
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-4
KFS 576A
Figure 6-1 Typical Bill of Material Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission permission of Honeywell.
6-5
KFS 576A
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission permission of Honeywell.
6-6
KFS 576A
PN DESCRIPTION REV ---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------071-1276-08 XPDR CTRL BK 28V 2 071-1276-09 XPDR CTRL BK 5V 2 071-1276-10 XPDR CTRL GY 28V 2 071-1276-99 COMMON DFSD AD ---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------SYMBOL PART NUMBER FIND NO DESCRIPTION UM -0008 -0009 -0010 -0099 ---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------REF1 300-03119-0000 FINAL ASSEMBLY RF . 00 . 00 . 00 . REF100 000-00388-0000 FLOW CHT KFS0576A RF .00 .00 . 00 . REF4 004-00448-0000 MPS KFS0576A RF . 00 .00 .00 . 012-01005-0002 TAPE MYLAR .500 W IN . . . 4 . 80 012-01127-0000 TAG COVER EA . . . 1.0 0 016-01412-0000 LOCTITE 425 AR . . . 1.00 035-01909-0001 PROTECTIVE COVER EA . . . 1.00 037-00083-0000 KFS 576A DISPLAY EA . . . 1.00 047-05021-0002 COVER W/FINISH EA . . . 1.00 057-01540-0000 WARNING HV TAG EA . . . 1 . 00 057-01764-0000 WRN TAG 5V LGT EA . 1 .00 . . 057-01764-0002 WRN TAG 28V LGT EA 1 . 00 . 1.00 . 057-02203-0008 FLAVOR STCKR EA 1 . 00 . . . 057-02203-0009 FLAVOR STCKR EA . 1.00 . . 057-02203-0010 FLAVOR STICKER EA . . 1.00 . 057-02337-0000 PRTCTV CVR DECAL EA . . . 1.0 0 057-02742-0000 S/N TAG, KFS 576A EA . . . 1.0 0 057-02831-0001 KFS DUP S/N TAG EA . . . 1 . 00 057-02834-0000 ESD TAG EA . . . 1.00 057-02888-0000 DECAL D.O.C. EA . . . 1.0 0 057-02890-0027 SCT KFS576A EA . . . 1.0 0 071-01276-0099 COMMON DFSD EA 1.00 1.00 1.00 . 073-00504-0003 BEZEL BLK EA 1 . 0 0 1 . 00 . . 073-00504-0004 BEZEL GRAY EA . . 1 . 00 . 073-00551-0004 KNOB W/H EA . . . 1.0 0 073-00553-0006 KNOB W/H EA 1.00 1.00 1.00 . 073-00554-0008 KNOB W/H EA . . . 1.0 0 076-00111-0001 STAND-OFF .605 EA . . . 1.00 088-01166-0002 INSERT -00 W/LENS EA 1.00 1.00 . . 088-01166-0004 INSERT -03 W/LENS EA . . 1. 0 0 . 089-05874-0003 SCR PHP 2-56X3/16 EA . . . 2.00 089-05874-0004 SCR PHP 2-56X1/4 EA . . . 9.0 0 089-05874-0005 SCR PHP 2-56X5/16 EA . . . 3.00 089-05874-0006 SCR PHP 2-56X3/8 EA . . . 1.0 0 089-06000-0003 SCR FHP 0-80X3/16 EA . . . 4 . 00 089-06004-0003 SCR FHP 2-56X3/16 EA . . . 2 . 00 089-06584-0000 SCR PHP 6-32X 1/2 EA . . . 2 . 00 090-00990-0001 PROTECTIVE CAP, SUB-D, 9P EA . . . 1 . 00 090-00990-0003 PROTECTIVE CAP, SUB-D, 15P EA EA . . . 1 . 00 091-00637-0002 INSULATOR, MYLAR EA . . . 1 .00 150-00018-0010 TUBING SHRINK WHT IN . . . 2 .00 150-00020-0010 TUBING SHRINK 18G IN . . . . 40 200-06579-0000 I/O BOARD ASSY EA 1 . 00 . 1.00 . 200-06579-0001 I/O BOARD ASSY EA . 1 . 00 . . 200-06580-0000 MICROPROCESSOR BD EA . . . 1.0 0 200-06589-0000 SW BD 28V W/SW EA 1 . 00 . 1.00 . 200-06589-0001 SW BD 5V W/SW EA . 1.0 0 . . 200-06626-0000 DRIVER BD EA . . . 1.00
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission permission of Honeywell.
6-7
KFS 576A
PN DESCRIPTION REV ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------071-1276-11 XPDR CTRL GY 5V 2 071-1276-13 XPDR CTRL BK 28V 2 071-1276-14 XPDR CTRL BK 5V 2 071-1276-99 COMMON DFSD AD ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------SYMBOL PART NUMBER FIND NO DESCRIPTION UM -0011 -0013 -0014 -0099 ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------REF1 300-03119-0000 FINAL ASSEMBLY RF .00 .00 .00 . REF100 000-00388-0000 FLOW CHT KFS0576A RF .00 .00 .00 . REF4 004-00448-0000 MPS KFS0576A RF .00 .00 .00 . 012-01005-0002 TAPE MYLAR .500 W IN . . . 4.80 012-01127-0000 TAG COVER EA . . . 1.00 016-01412-0000 LOCTITE 425 AR . . . 1.00 035-01909-0001 PROTECTIVE COVER EA . . . 1.00 037-00083-0000 KFS 576A DISPLAY EA . . . 1.00 047-05021-0002 COVER W/FINISH EA . . . 1.00 057-01540-0000 WARNING HV TAG EA . . . 1.00 057-01764-0000 WRN TAG 5V LGT EA 1.00 . 1.00 . 057-01764-0002 WRN TAG 28V LGT EA . 1.00 . . 057-02203-0011 FLAVOR STICKER EA 1.00 . . . 057-02203-0013 FLAVOR STCKR EA . 1.00 . . 057-02203-0014 FLAVOR STCKR EA . . 1.00 . 057-02337-0000 PRTCTV CVR DECAL EA . . . 1.00 057-02742-0000 S/N TAG, KFS 576A EA . . . 1.00 057-02831-0001 KFS DUP S/N TAG EA . . . 1.00 057-02834-0000 ESD TAG EA . . . 1.00 057-02888-0000 DECAL D.O.C. EA . . . 1.00 057-02890-0027 SCT KFS576A EA . . . 1.00 071-01276-0099 COMMON DFSD EA 1.00 1.00 1.00 . 073-00504-0003 BEZEL BLK EA . 1.00 1.00 . 073-00504-0004 BEZEL GRAY EA 1.00 . . . 073-00551-0004 KNOB W/H EA . . . 1.00 073-00553-0006 KNOB W/H EA 1.00 1.00 1.00 . 073-00554-0008 KNOB W/H EA . . . 1.00 076-00111-0001 STAND-OFF .605 EA . . . 1.00 088-01166-0004 INSERT -03 W/LENS EA 1.00 . . . 088-01166-0006 INSERT -05 W/LENS EA . 1.00 1.00 . 089-05874-0003 SCR PHP 2-56X3/16 EA . . . 2.00 089-05874-0004 SCR PHP 2-56X1/4 EA . . . 9.00 089-05874-0005 SCR PHP 2-56X5/16 EA . . . 3.00 089-05874-0006 SCR PHP 2-56X3/8 EA . . . 1.00 089-06000-0003 SCR FHP 0-80X3/16 EA . . . 4.00 089-06004-0003 SCR FHP 2-56X3/16 EA . . . 2.00 089-06584-0000 SCR PHP 6-32X 1/2 EA . . . 2.00 090-00990-0001 PROTECTIVE CAP, SUB-D, 9P EA . . . 1.00 090-00990-0003 PROTECTIVE CAP, SUB-D, 15P EA . . . 1.00 091-00637-0002 INSULATOR, MYLAR EA . . . 1.00 150-00018-0010 TUBING SHRINK WHT IN . . . 2.00 150-00020-0010 TUBING SHRINK 18G IN . . . .40 200-06579-0000 I/O BOARD ASSY EA . 1.00 . . 200-06579-0001 I/O BOARD ASSY EA 1.00 . 1.00 . 200-06580-0000 MICROPROCESSOR BD EA . . . 1.00 200-06589-0001 SW BD 5V W/SW EA 1.00 . . . 200-06589-0002 SW BD 28V SW 1/2 EA . 1.00 . . 200-06589-0003 SW BD 5V SW 1/2 EA . . 1.00 . 200-06626-0000 DRIVER BD EA . . . 1.00
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-8
KFS 576A
PN DESCRIPTION REV ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------071-1276-15 XPDR CTRL GY 28V 2 071-1276-16 XPDR CTRL GY 5V 2 071-1276-18 XPDR CTRL BK 28V 2 071-1276-99 COMMON DFSD AD ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------SYMBOL PART NUMBER FIND NO DESCRIPTION UM -0015 -0016 -0018 -0099 ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------REF1 300-03119-0000 FINAL ASSEMBLY RF .00 .00 .00 . REF100 000-00388-0000 FLOW CHT KFS0576A RF .00 .00 .00 . REF4 004-00448-0000 MPS KFS0576A RF .00 .00 .00 . 012-01005-0002 TAPE MYLAR .500 W IN . . . 4.80 012-01127-0000 TAG COVER EA . . . 1.00 016-01412-0000 LOCTITE 425 AR . . . 1.00 035-01909-0001 PROTECTIVE COVER EA . . . 1.00 037-00083-0000 KFS 576A DISPLAY EA . . . 1.00 047-05021-0002 COVER W/FINISH EA . . . 1.00 057-01540-0000 WARNING HV TAG EA . . . 1.00 057-01764-0000 WRN TAG 5V LGT EA . 1.00 . . 057-01764-0002 WRN TAG 28V LGT EA 1.00 . 1.00 . 057-02203-0015 FLAVOR STCKR EA 1.00 . . . 057-02203-0016 FLAVOR STCKR EA . 1.00 . . 057-02203-0018 FLAVOR STCKR EA . . 1.00 . 057-02337-0000 PRTCTV CVR DECAL EA . . . 1.00 057-02742-0000 S/N TAG, KFS 576A EA . . . 1.00 057-02831-0001 KFS DUP S/N TAG EA . . . 1.00 057-02834-0000 ESD TAG EA . . . 1.00 057-02888-0000 DECAL D.O.C. EA . . . 1.00 057-02890-0027 SCT KFS576A EA . . . 1.00 071-01276-0099 COMMON DFSD EA 1.00 1.00 1.00 . 073-00504-0003 BEZEL BLK EA . . 1.00 . 073-00504-0004 BEZEL GRAY EA 1.00 1.00 . . 073-00551-0004 KNOB W/H EA . . . 1.00 073-00553-0006 KNOB W/H EA 1.00 1.00 1.00 . 073-00554-0008 KNOB W/H EA . . . 1.00 076-00111-0001 STAND-OFF .605 EA . . . 1.00 088-01166-0001 INSERT -00 W/LENS EA . . 1.00 . 088-01166-0008 INSERT -07 W/LENS EA 1.00 1.00 . . 089-05874-0003 SCR PHP 2-56X3/16 EA . . . 2.00 089-05874-0004 SCR PHP 2-56X1/4 EA . . . 9.00 089-05874-0005 SCR PHP 2-56X5/16 EA . . . 3.00 089-05874-0006 SCR PHP 2-56X3/8 EA . . . 1.00 089-06000-0003 SCR FHP 0-80X3/16 EA . . . 4.00 089-06004-0003 SCR FHP 2-56X3/16 EA . . . 2.00 089-06584-0000 SCR PHP 6-32X 1/2 EA . . . 2.00 090-00990-0001 PROTECTIVE CAP, SUB-D, 9P EA . . . 1.00 090-00990-0003 PROTECTIVE CAP, SUB-D, 15P EA . . . 1.00 091-00637-0002 INSULATOR, MYLAR EA . . . 1.00 150-00018-0010 TUBING SHRINK WHT IN . . . 2.00 150-00020-0010 TUBING SHRINK 18G IN . . . .40 200-06579-0000 I/O BOARD ASSY EA 1.00 . 1.00 . 200-06579-0001 I/O BOARD ASSY EA . 1.00 . . 200-06580-0000 MICROPROCESSOR BD EA . . . 1.00 200-06589-0000 SW BD 28V W/SW EA . . 1.00 . 200-06589-0002 SW BD 28V SW 1/2 EA 1.00 . . . 200-06589-0003 SW BD 5V SW 1/2 EA . 1.00 . . 200-06626-0000 DRIVER BD EA . . . 1.00
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-9
KFS 576A
PN DESCRIPTION REV ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------071-1276-19 XPDR CTRL BK 28V 2 071-1276-20 XPDR CTRL BK 5V 2 071-1276-21 XPDR CTRL GY 28V 2 071-1276-99 COMMON DFSD AD ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------SYMBOL PART NUMBER FIND NO DESCRIPTION UM -0019 -0020 -0021 -0099 ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------REF1 300-03119-0000 FINAL ASSEMBLY RF .00 .00 .00 . REF100 000-00388-0000 FLOW CHT KFS0576A RF .00 .00 .00 . REF4 004-00448-0000 MPS KFS0576A RF .00 .00 .00 . 012-01005-0002 TAPE MYLAR .500 W IN . . . 4.80 012-01127-0000 TAG COVER EA . . . 1.00 016-01412-0000 LOCTITE 425 AR . . . 1.00 035-01909-0001 PROTECTIVE COVER EA . . . 1.00 037-00083-0000 KFS 576A DISPLAY EA . . . 1.00 047-05021-0002 COVER W/FINISH EA . . . 1.00 057-01540-0000 WARNING HV TAG EA . . . 1.00 057-01764-0000 WRN TAG 5V LGT EA . 1.00 . . 057-01764-0002 WRN TAG 28V LGT EA 1.00 . 1.00 . 057-02203-0019 FLAVOR STCKR EA 1.00 . . . 057-02203-0020 FLAVOR STCKR EA . 1.00 . . 057-02203-0021 FLAVOR STCKR EA . . 1.00 . 057-02337-0000 PRTCTV CVR DECAL EA . . . 1.00 057-02742-0000 S/N TAG, KFS 576A EA . . . 1.00 057-02831-0001 KFS DUP S/N TAG EA . . . 1.00 057-02834-0000 ESD TAG EA . . . 1.00 057-02888-0000 DECAL D.O.C. EA . . . 1.00 057-02890-0027 SCT KFS576A EA . . . 1.00 071-01276-0099 COMMON DFSD EA 1.00 1.00 1.00 . 073-00504-0003 BEZEL BLK EA 1.00 1.00 . . 073-00504-0004 BEZEL GRAY EA . . 1.00 . 073-00551-0004 KNOB W/H EA . . . 1.00 073-00554-0008 KNOB W/H EA . . . 1.00 076-00111-0001 STAND-OFF .605 EA . . . 1.00 088-01166-0010 INSERT -09 W/LENS EA 1.00 1.00 . . 088-01166-0012 INSERT -11 W/LENS EA . . 1.00 . 089-05874-0003 SCR PHP 2-56X3/16 EA . . . 2.00 089-05874-0004 SCR PHP 2-56X1/4 EA . . . 9.00 089-05874-0005 SCR PHP 2-56X5/16 EA . . . 3.00 089-05874-0006 SCR PHP 2-56X3/8 EA . . . 1.00 089-06000-0003 SCR FHP 0-80X3/16 EA . . . 4.00 089-06004-0003 SCR FHP 2-56X3/16 EA . . . 2.00 089-06584-0000 SCR PHP 6-32X 1/2 EA . . . 2.00 090-00990-0001 PROTECTIVE CAP, SUB-D, 9P EA . . . 1.00 090-00990-0003 PROTECTIVE CAP, SUB-D, 15P EA . . . 1.00 091-00637-0002 INSULATOR, MYLAR EA . . . 1.00 150-00018-0010 TUBING SHRINK WHT IN . . . 2.00 150-00020-0010 TUBING SHRINK 18G IN . . . .40 200-06579-0000 I/O BOARD ASSY EA 1.00 . 1.00 . 200-06579-0001 I/O BOARD ASSY EA . 1.00 . . 200-06580-0000 MICROPROCESSOR BD EA . . . 1.00 200-06589-0004 SW BD 28V NO SW EA 1.00 . 1.00 . 200-06589-0005 SW BD 5V NO SW EA . 1.00 . . 200-06626-0000 DRIVER BD EA . . . 1.00
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-10
KFS 576A
PN DESCRIPTION REV ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------071-1276-22 XPDR CTRL GY 5V 2 071-1276-23 XPDR CTRL BK 28V 2 071-1276-24 XPDR CTRL BK 5V 2 071-1276-99 COMMON DFSD AD ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------SYMBOL PART NUMBER FIND NO DESCRIPTION UM -0022 -0023 -0024 -0099 ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------REF1 300-03119-0000 FINAL ASSEMBLY RF .00 .00 .00 . REF100 000-00388-0000 FLOW CHT KFS0576A RF .00 .00 .00 . REF4 004-00448-0000 MPS KFS0576A RF .00 .00 .00 . 012-01005-0002 TAPE MYLAR .500 W IN . . . 4.80 012-01127-0000 TAG COVER EA . . . 1.00 016-01412-0000 LOCTITE 425 AR . . . 1.00 035-01909-0001 PROTECTIVE COVER EA . . . 1.00 037-00083-0000 KFS 576A DISPLAY EA . . . 1.00 047-05021-0002 COVER W/FINISH EA . . . 1.00 057-01540-0000 WARNING HV TAG EA . . . 1.00 057-01764-0000 WRN TAG 5V LGT EA 1.00 . 1.00 . 057-01764-0002 WRN TAG 28V LGT EA . 1.00 . . 057-02203-0022 FLAVOR STCKR EA 1.00 . . . 057-02203-0023 FLAVOR STCKR EA . 1.00 . . 057-02203-0024 FLAVOR STCKR EA . . 1.00 . 057-02337-0000 PRTCTV CVR DECAL EA . . . 1.00 057-02742-0000 S/N TAG, KFS 576A EA . . . 1.00 057-02831-0001 KFS DUP S/N TAG EA . . . 1.00 057-02834-0000 ESD TAG EA . . . 1.00 057-02888-0000 DECAL D.O.C. EA . . . 1.00 057-02890-0027 SCT KFS576A EA . . . 1.00 071-01276-0099 COMMON DFSD EA 1.00 1.00 1.00 . 073-00504-0003 BEZEL BLK EA . 1.00 1.00 . 073-00504-0004 BEZEL GRAY EA 1.00 . . . 073-00551-0004 KNOB W/H EA . . . 1.00 073-00553-0006 KNOB W/H EA . 1.00 1.00 . 073-00554-0008 KNOB W/H EA . . . 1.00 076-00111-0001 STAND-OFF .605 EA . . . 1.00 088-01166-0012 INSERT -11 W/LENS EA 1.00 . . . 088-01166-0014 INSERT -13 W/LENS EA . 1.00 1.00 . 089-05874-0003 SCR PHP 2-56X3/16 EA . . . 2.00 089-05874-0004 SCR PHP 2-56X1/4 EA . . . 9.00 089-05874-0005 SCR PHP 2-56X5/16 EA . . . 3.00 089-05874-0006 SCR PHP 2-56X3/8 EA . . . 1.00 089-06000-0003 SCR FHP 0-80X3/16 EA . . . 4.00 089-06004-0003 SCR FHP 2-56X3/16 EA . . . 2.00 089-06584-0000 SCR PHP 6-32X 1/2 EA . . . 2.00 090-00990-0001 PROTECTIVE CAP, SUB-D, 9P EA . . . 1.00 090-00990-0003 PROTECTIVE CAP, SUB-D, 15P EA . . . 1.00 091-00637-0002 INSULATOR, MYLAR EA . . . 1.00 150-00018-0010 TUBING SHRINK WHT IN . . . 2.00 150-00020-0010 TUBING SHRINK 18G IN . . . .40 200-06579-0000 I/O BOARD ASSY EA . 1.00 . . 200-06579-0001 I/O BOARD ASSY EA 1.00 . 1.00 . 200-06580-0000 MICROPROCESSOR BD EA . . . 1.00 200-06589-0005 SW BD 5V NO SW EA 1.00 . . . 200-06589-0006 SW BD 28V 1/2 EA . 1.00 . . 200-06589-0007 SW BD 5V 1/2 EA . . 1.00 . 200-06626-0000 DRIVER BD EA . . . 1.00
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-11
KFS 576A
PN DESCRIPTION REV ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------071-1276-25 XPDR CTRL BY 28V 2 071-1276-26 XPDR CTRL GY 5V 2 071-1276-99 COMMON DFSD AD ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------SYMBOL PART NUMBER FIND NO DESCRIPTION UM -0025 -0026 -0099 ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------REF1 300-03119-0000 FINAL ASSEMBLY RF .00 .00 . REF100 000-00388-0000 FLOW CHT KFS0576A RF .00 .00 . REF4 004-00448-0000 MPS KFS0576A RF .00 .00 . 012-01005-0002 TAPE MYLAR .500 W IN . . 4.80 012-01127-0000 TAG COVER EA . . 1.00 016-01412-0000 LOCTITE 425 AR . . 1.00 035-01909-0001 PROTECTIVE COVER EA . . 1.00 037-00083-0000 KFS 576A DISPLAY EA . . 1.00 047-05021-0002 COVER W/FINISH EA . . 1.00 057-01540-0000 WARNING HV TAG EA . . 1.00 057-01764-0000 WRN TAG 5V LGT EA . 1.00 . 057-01764-0002 WRN TAG 28V LGT EA 1.00 . . 057-02203-0025 FLAVOR STCKR EA 1.00 . . 057-02203-0026 FLAVOR STCKR EA . 1.00 . 057-02337-0000 PRTCTV CVR DECAL EA . . 1.00 057-02742-0000 S/N TAG, KFS 576A EA . . 1.00 057-02831-0001 KFS DUP S/N TAG EA . . 1.00 057-02834-0000 ESD TAG EA . . 1.00 057-02888-0000 DECAL D.O.C. EA . . 1.00 057-02890-0027 SCT KFS576A EA . . 1.00 071-01276-0099 COMMON DFSD EA 1.00 1.00 . 073-00504-0004 BEZEL GRAY EA 1.00 1.00 . 073-00551-0004 KNOB W/H EA . . 1.00 073-00553-0006 KNOB W/H EA 1.00 1.00 . 073-00554-0008 KNOB W/H EA . . 1.00 076-00111-0001 STAND-OFF .605 EA . . 1.00 088-01166-0016 INSERT -15 W/LENS EA 1.00 1.00 . 089-05874-0003 SCR PHP 2-56X3/16 EA . . 2.00 089-05874-0004 SCR PHP 2-56X1/4 EA . . 9.00 089-05874-0005 SCR PHP 2-56X5/16 EA . . 3.00 089-05874-0006 SCR PHP 2-56X3/8 EA . . 1.00 089-06000-0003 SCR FHP 0-80X3/16 EA . . 4.00 089-06004-0003 SCR FHP 2-56X3/16 EA . . 2.00 089-06584-0000 SCR PHP 6-32X 1/2 EA . . 2.00 090-00990-0001 PROTECTIVE CAP, SUB-D, 9P EA . . 1.00 090-00990-0003 PROTECTIVE CAP, SUB-D, 15P EA . . 1.00 091-00637-0002 INSULATOR, MYLAR EA . . 1.00 150-00018-0010 TUBING SHRINK WHT IN . . 2.00 150-00020-0010 TUBING SHRINK 18G IN . . .40 200-06579-0000 I/O BOARD ASSY EA 1.00 . . 200-06579-0001 I/O BOARD ASSY EA . 1.00 . 200-06580-0000 MICROPROCESSOR BD EA . . 1.00 200-06589-0006 SW BD 28V 1/2 EA 1.00 . . 200-06589-0007 SW BD 5V 1/2 EA . 1.00 . 200-06626-0000 DRIVER BD EA . . 1.00
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-12
KFS 576A
THE FOLLOWING IS THE PARTS LIST FROM THE PREVIOUS REVISION AND IS PROVIDED FOR REFERENCE ONLY.
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-13
KFS 576A
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-14
KFS 576A
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-15
KFS 576A
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-16
KFS 576A
Figure 6-2 Final Assembly (Dwg No 300-03119-0000 Rev AD) Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-17
KFS 576A
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-18
KFS 576A
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-18
KFS 576A
Figure 6-3 Final Assembly (Dwg No 300-03119-0000 Rev 7) (For Reference Only) Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-19
KFS 576A
Figure 6-3 Final Assembly (Dwg No 300-03119-0000 Rev 7) (For Reference Only) Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-19
KFS 576A
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-20
KFS 576A
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-20
KFS 576A
PN DESCRIPTION REV ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------200-06579-0000 I/O BOARD ASSY AA 200-06579-0001 I/O BOARD ASSY 3 200-06579-0099 COMMON I/O BD ASSY AA ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------SYMBOL PART NUMBER FIND NO DESCRIPTION UM -0000 -0001 -0099 ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------C101 111-00001-0017 CAP CR 180PF 50V EA . . 1.00 C102 111-00001-0017 CAP CR 180PF 50V EA . . 1.00 C103 999-09999-0098 PLACE HOLDER RF .00 .00 . C104 999-09999-0098 PLACE HOLDER RF .00 .00 . C105 096-01082-0010 CAP TN 10UF 35V EA . . 1.00 C106 096-01082-0005 CAP TN 10UF 20V EA . . 1.00 C107 999-09999-0098 PLACE HOLDER RF .00 .00 . C108 111-00001-0001 CAP CR .1UF 50V EA . . 1.00 C109 111-00001-0001 CAP CR .1UF 50V EA . . 1.00 C110 111-00001-0017 CAP CR 180PF 50V EA . . 1.00 C111 111-00001-0066 CAP CR 33PF 50V EA . . 1.00 C112 111-00001-0066 CAP CR 33PF 50V EA . . 1.00 C113 111-00001-0017 CAP CR 180PF 50V EA . . 1.00 C114 111-00001-0017 CAP CR 180PF 50V EA . . 1.00 C115 111-00001-0017 CAP CR 180PF 50V EA . . 1.00 CJ101 026-00018-0001 WIRE CKTJMPR 24AWG EA . 1.00 . CJ102 026-00018-0001 WIRE CKTJMPR 24AWG EA 1.00 . . CR101 007-06016-0000 DIO S 1N4154 EA . . 1.00 CR102 007-06016-0000 DIO S 1N4154 EA . . 1.00 CR103 007-06016-0000 DIO S 1N4154 EA . . 1.00 CR104 007-06016-0000 DIO S 1N4154 EA . . 1.00 CR105 007-06016-0000 DIO S 1N4154 EA . . 1.00 CR106 007 06016 0000 DIO S 1N4154 EA 1 00
KFS 576A
PN DESCRIPTION REV ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------200-06579-0000 I/O BOARD ASSY AA 200-06579-0001 I/O BOARD ASSY 3 200-06579-0099 COMMON I/O BD ASSY AA ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------SYMBOL PART NUMBER FIND NO DESCRIPTION UM -0000 -0001 -0099 ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------C101 111-00001-0017 CAP CR 180PF 50V EA . . 1.00 C102 111-00001-0017 CAP CR 180PF 50V EA . . 1.00 C103 999-09999-0098 PLACE HOLDER RF .00 .00 . C104 999-09999-0098 PLACE HOLDER RF .00 .00 . C105 096-01082-0010 CAP TN 10UF 35V EA . . 1.00 C106 096-01082-0005 CAP TN 10UF 20V EA . . 1.00 C107 999-09999-0098 PLACE HOLDER RF .00 .00 . C108 111-00001-0001 CAP CR .1UF 50V EA . . 1.00 C109 111-00001-0001 CAP CR .1UF 50V EA . . 1.00 C110 111-00001-0017 CAP CR 180PF 50V EA . . 1.00 C111 111-00001-0066 CAP CR 33PF 50V EA . . 1.00 C112 111-00001-0066 CAP CR 33PF 50V EA . . 1.00 C113 111-00001-0017 CAP CR 180PF 50V EA . . 1.00 C114 111-00001-0017 CAP CR 180PF 50V EA . . 1.00 C115 111-00001-0017 CAP CR 180PF 50V EA . . 1.00 CJ101 026-00018-0001 WIRE CKTJMPR 24AWG EA . 1.00 . CJ102 026-00018-0001 WIRE CKTJMPR 24AWG EA 1.00 . . CR101 007-06016-0000 DIO S 1N4154 EA . . 1.00 CR102 007-06016-0000 DIO S 1N4154 EA . . 1.00 CR103 007-06016-0000 DIO S 1N4154 EA . . 1.00 CR104 007-06016-0000 DIO S 1N4154 EA . . 1.00 CR105 007-06016-0000 DIO S 1N4154 EA . . 1.00 CR106 007-06016-0000 DIO S 1N4154 EA . . 1.00 CR107 007-06016-0000 DIO S 1N4154 EA . . 1.00 CR108 007-06016-0000 DIO S 1N4154 EA . . 1.00 CR109 007-06016-0000 DIO S 1N4154 EA . . 1.00 CR110 007-06016-0000 DIO S 1N4154 EA . . 1.00 CR111 007-06016-0000 DIO S 1N4154 EA . . 1.00 CR112 007-06016-0000 DIO S 1N4154 EA . . 1.00 CR113 007-06016-0000 DIO S 1N4154 EA . . 1.00 CR114 007-06016-0000 DIO S 1N4154 EA . . 1.00 CR115 007-06016-0000 DIO S 1N4154 EA . . 1.00 CR116 007-06016-0000 DIO S 1N4154 EA . . 1.00 CR117 007-06016-0000 DIO S 1N4154 EA . . 1.00 CR118 007-06016-0000 DIO S 1N4154 EA . . 1.00 CR119 007-06016-0000 DIO S 1N4154 EA 1.00 1.00 . CR120 007-06025-0000 DIO S 1N4003 EA . . 1.00 CR121 007-06025-0000 DIO S 1N4003 EA . . 1.00 CR122 007-06025-0000 DIO S 1N4003 EA . . 1.00 CR123 007-06025-0000 DIO S 1N4003 EA . . 1.00 I101 120-06116-0000 IC HEF4512BTD EA . . 1.00 I102 120-06116-0000 IC HEF4512BTD EA . . 1.00 I103 120-03174-0001 IC TDB0082FP EA . . 1.00 I104 120-03174-0001 IC TDB0082FP EA . . 1.00 I105 120-03174-0001 IC TDB0082FP EA . . 1.00 I106 120-03116-0003 IC LM137H EA . . 1.00 J101 030-02458-0014 CONN STRGT 14P EA . . 1.00 J102 030-02322-0019 HEADER 19P EA . . 1.00 J103 030-02174-0004 PIN CONTACT EA . . 11.00 J5761 030-02358-0007 CONN SUB-D PC 29P EA . . 1.00 J5762 030-02346-0008 CONN SUB-D CA 9P EA . . 1.00 L101 013-00006-0003 FERR BEAD EA . . 1.00 L102 013-00006-0003 FERR BEAD EA . . 1.00 L103 013-00006-0003 FERR BEAD EA . . 1.00 L104 013-00006-0003 FERR BEAD EA . . 1.00 L105 013-00006-0003 FERR BEAD EA . . 1.00
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-21
KFS 576A
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------SYMBOL PART NUMBER FIND NO DESCRIPTION UM -0000 -0001 -0099 ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------L106 013-00006-0003 FERR BEAD EA . . 1.00 L107 013-00006-0003 FERR BEAD EA . . 1.00 L108 013-00006-0003 FERR BEAD EA . . 1.00 L109 013-00006-0003 FERR BEAD EA . . 1.00 L110 013-00006-0003 FERR BEAD EA . . 1.00 L111 013-00006-0003 FERR BEAD EA . . 1.00 L112 013-00006-0003 FERR BEAD EA . . 1.00 L113 013-00006-0003 FERR BEAD EA . . 1.00 L114 013-00006-0003 FERR BEAD EA . . 1.00 L115 013-00006-0003 FERR BEAD EA . . 1.00 L116 013-00006-0003 FERR BEAD EA . . 1.00 L117 013-00006-0003 FERR BEAD EA . . 1.00 L118 013-00006-0003 FERR BEAD EA . . 1.00 L119 013-00006-0003 FERR BEAD EA . . 1.00 L120 013-00006-0003 FERR BEAD EA . . 1.00 L121 013-00006-0003 FERR BEAD EA . . 1.00 L122 999-09999-0098 PLACE HOLDER RF . . .00 L123 013-00006-0003 FERR BEAD EA . . 1.00 L124 013-00006-0003 FERR BEAD EA . . 1.00 L125 013-00006-0003 FERR BEAD EA . . 1.00 L126 013-00006-0003 FERR BEAD EA . . 1.00 L127 013-00006-0003 FERR BEAD EA . . 1.00 L128 013-00006-0003 FERR BEAD EA . . 1.00 L129 013-00006-0003 FERR BEAD EA . . 1.00 Q101 007-00467-0000 XSTR S NPN MMBTA06 EA . . 1.00 Q102 007-00466-0000 XSTR S PNP MMBTA56 EA . . 1.00 Q103 007-00467-0000 XSTR S NPN MMBTA06 EA . . 1.00 Q104 007-00466-0000 XSTR S PNP MMBTA56 EA . . 1.00 Q105 007-00467-0000 XSTR S NPN MMBTA06 EA . . 1.00 Q106 007-00467-0000 XSTR S NPN MMBTA06 EA . . 1.00 Q107 007-00466-0000 XSTR S PNP MMBTA56 EA . . 1.00 Q108 007-00467-0000 XSTR S NPN MMBTA06 EA . . 1.00 Q109 007-00467-0000 XSTR S NPN MMBTA06 EA . . 1.00 Q110 007-00466-0000 XSTR S PNP MMBTA56 EA . . 1.00 R101 131-00223-0013 RES CF 22K EW 5% EA . . 1.00 R102 131-00223-0013 RES CF 22K EW 5% EA . . 1.00 R103 131-00223-0013 RES CF 22K EW 5% EA . . 1.00 R104 131-00223-0013 RES CF 22K EW 5% EA . . 1.00 R105 131-00223-0013 RES CF 22K EW 5% EA . . 1.00 R106 131-00223-0013 RES CF 22K EW 5% EA . . 1.00 R107 131-00223-0013 RES CF 22K EW 5% EA . . 1.00 R108 131-00223-0013 RES CF 22K EW 5% EA . . 1.00 R109 131-00223-0013 RES CF 22K EW 5% EA . . 1.00 R110 131-00223-0013 RES CF 22K EW 5% EA . . 1.00 R111 131-00223-0013 RES CF 22K EW 5% EA . . 1.00 R112 131-00223-0013 RES CF 22K EW 5% EA . . 1.00 R113 131-00223-0013 RES CF 22K EW 5% EA . . 1.00 R114 131-00223-0013 RES CF 22K EW 5% EA . . 1.00 R115 131-00223-0013 RES CF 22K EW 5% EA . . 1.00 R116 131-00223-0013 RES CF 22K EW 5% EA . . 1.00 R117 131-00103-0013 RES CF 10K EW 5% EA . . 1.00 R118 131-00103-0013 RES CF 10K EW 5% EA . . 1.00 R119 131-00223-0013 RES CF 22K EW 5% EA . . 1.00 R120 131-00223-0013 RES CF 22K EW 5% EA . . 1.00 R121 131-00360-0023 RES CF 36 QW 5% EA . . 1.00 R122 131-00330-0023 RES CF 33 QW 5% EA . . 1.00 R123 131-00102-0013 RES CF 1K EW 5% EA . . 1.00 R124 131-00273-0013 RES CF 27K EW 5% EA . . 1.00 R125 131-00273-0013 RES CF 27K EW 5% EA . . 1.00 R126 131-00203-0013 RES CF 20K EW 5% EA . . 1.00 R127 131-00203-0013 RES CF 20K EW 5% EA . . 1.00 R128 131-00102-0013 RES CF 1K EW 5% EA . . 1.00
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-22
KFS 576A
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------SYMBOL PART NUMBER FIND NO DESCRIPTION UM -0000 -0001 -0099 ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------R129 131-00102-0013 RES CF 1K EW 5% EA . . 1.00 R130 131-00203-0013 RES CF 20K EW 5% EA . . 1.00 R131 131-00203-0013 RES CF 20K EW 5% EA . . 1.00 R132 131-00273-0013 RES CF 27K EW 5% EA . . 1.00 R133 131-00273-0013 RES CF 27K EW 5% EA . . 1.00 R134 131-00102-0013 RES CF 1K EW 5% EA . . 1.00 R135 131-00360-0023 RES CF 36 QW 5% EA . . 1.00 R136 131-00330-0023 RES CF 33 QW 5% EA . . 1.00 R137 131-00104-0013 RES CF 100K EW 5% EA . . 1.00 R138 131-00104-0013 RES CF 100K EW 5% EA . . 1.00 R139 131-00104-0013 RES CF 100K EW 5% EA . . 1.00 R140 131-00104-0013 RES CF 100K EW 5% EA . . 1.00 R141 131-00822-0013 RES CF 8.2K EW 5% EA . . 1.00 R142 999-09999-0098 PLACE HOLDER RF .00 .00 . R143 999-09999-0098 PLACE HOLDER RF .00 .00 . R144 999-09999-0098 PLACE HOLDER RF .00 .00 . R145 999-09999-0098 PLACE HOLDER RF .00 .00 . R146 999-09999-0098 PLACE HOLDER RF .00 .00 . R147 999-09999-0098 PLACE HOLDER RF .00 .00 . R148 999-09999-0098 PLACE HOLDER RF .00 .00 . R149 999-09999-0098 PLACE HOLDER RF .00 .00 . R150 999-09999-0098 PLACE HOLDER RF .00 .00 . R151 131-00103-0013 RES CF 10K EW 5% EA . . 1.00 R152 131-00103-0013 RES CF 10K EW 5% EA . . 1.00 R153 131-00103-0013 RES CF 10K EW 5% EA . . 1.00 R154 131-00103-0013 RES CF 10K EW 5% EA . . 1.00 R155 131-00433-0013 RES CF 43K EW 5% EA . . 1.00 R156 131-00102-0013 RES CF 1K EW 5% EA . . 1.00 R157 131-00102-0013 RES CF 1K EW 5% EA . . 1.00 R158 131-00103-0013 RES CF 10K EW 5% EA . . 1.00 R159 131-00102-0013 RES CF 1K EW 5% EA . . 1.00 R160 131-00241-0013 RES CF 240 EW 5% EA . . 1.00 R161 131-00162-0013 RES CF 1.6K EW 5% EA . . 1.00 R162 131-00103-0013 RES CF 10K EW 5% EA . . 1.00 R163 131-00103-0013 RES CF 10K EW 5% EA . . 1.00 R164 131-00104-0013 RES CF 100K EW 5% EA . . 1.00 REF1 300-06579-0000 I/O BOARD RF .00 .00 .00 TP101 008-00096-0001 TERMINAL TEST PNT EA . . 1.00 TP102 008-00096-0001 TERMINAL TEST PNT EA . . 1.00 TP103 008-00096-0001 TERMINAL TEST PNT EA . . 1.00 TP104 008-00096-0001 TERMINAL TEST PNT EA . . 1.00 TP105 008-00096-0001 TERMINAL TEST PNT EA . . 1.00 U101 015-00039-0000 RES MOD 10K150V2% EA . . 1.00 U102 015-00039-0000 RES MOD 10K150V2% EA . . 1.00 U103 015-00064-0013 8P CAP 220PF 10% EA . . 1.00 U104 015-00064-0013 8P CAP 220PF 10% EA . . 1.00 U105 015-00064-0013 8P CAP 220PF 10% EA . . 1.00 002-06579-0000 SCH I/O BD KFS 576A RF .00 . . 008-00038-0001 TERM BIFUR .084L EA . . 6.00 009-06579-0000 PC BD I/O EA . . 1.00 016-01040-0000 COATING TYPE AR AR . . .00 025-00018-0011 WIRE 26 BRN IN . . 6.00 025-00018-0022 WIRE 26 RED IN . . 6.00 025-00018-0033 WIRE 26 ORG IN . . 6.00 025-00018-0044 WIRE 26 YEL IN . . 6.00 025-00018-0055 WIRE 26 GRN IN . . 6.00 025-00018-0066 WIRE 26 BLU IN . . 6.00 030-02352-0000 LOCK TAB EA . . 2.00 073-00454-0004 CAST MOD W/F EA . . 1.00 076-00741-0009 STANDOFF .120 EA . . 3.00 076-00741-0011 STANDOFF .120 EA . . 1.00 089-05874-0004 SCR PHP 2-56X1/4 EA . . 6.00
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-23
KFS 576A
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------SYMBOL PART NUMBER FIND NO DESCRIPTION UM -0000 -0001 -0099 ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------091-00025-0000 WSHR XSTR INSUL EA . . 1.00 091-00109-0000 CABLE TIE EA . . 2.00 150-00018-0010 TUBING SHRINK WHT AR . . 1.00 192-06579-0000 KFS 576A I/O BOARD ASSY RF .00 . .00 200-06579-0099 COMMON I/O BD ASSY EA 1.00 1.00 .
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-24
KFS 576A
THE FOLLOWING IS THE PARTS LIST FROM THE PREVIOUS REVISION AND IS PROVIDED FOR REFERENCE ONLY.
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-25
KFS 576A
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-26
KFS 576A
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-27
KFS 576A
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-28
KFS 576A
Figure 6-4 I/O Board (Dwg No 300-06570-0000 Rev 1) Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-29
KFS 576A
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-30
KFS 576A
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-30
KFS 576A
Figure 6-5 I/O Board (Dwg No 300-06579-0000 Rev 0) (For Reference Only) Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-31
KFS 576A
Figure 6-5 I/O Board (Dwg No 300-06579-0000 Rev 0) (For Reference Only) Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-31
KFS 576A
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-32
KFS 576A
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-32
KFS 576A
Figure 6-6 I/O Board Schematic (Dwg No 002-06579-0000 Rev 3) (Sheet 1 of 2) Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-33
KFS 576A
Figure 6-6 I/O Board Schematic (Dwg No 002-06579-0000 Rev 3) (Sheet 1 of 2) Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-33
KFS 576A
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-34
KFS 576A
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-34
KFS 576A
Figure 6-6 I/O Board Schematic (Dwg No 002-06579-0000 Rev 3) (Sheet 2 of 2) Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-35
KFS 576A
Figure 6-6 I/O Board Schematic (Dwg No 002-06579-0000 Rev 3) (Sheet 2 of 2) Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-35
KFS 576A
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-36
KFS 576A
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-36
KFS 576A
PN DESCRIPTION REV ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------200-06580-0000 MICROPROCESSOR BD AA ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------SYMBOL PART NUMBER FIND NO DESCRIPTION UM -0000 ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------C201 111-00001-0032 CAP CR 1UF 50V EA 1.00 C202 111-00001-0013 CAP CR .1UF 50V EA 1.00 C203 111-00001-0013 CAP CR .1UF 50V EA 1.00 C204 111-00001-0077 CAP CR 12PF 100V EA 1.00 C205 111-00001-0077 CAP CR 12PF 100V EA 1.00 C206 111-00001-0077 CAP CR 12PF 100V EA 1.00 C207 111-00001-0077 CAP CR 12PF 100V EA 1.00 C208 096-01082-0015 CAP TN 2.2UF 15V EA 1.00 I201 120-02119-0000 NONVOLATILE RAM EA 1.00 I202 125-00036-0000 429 I/O MICRO EA 1.00 I203 125-00035-0001 576A DSPLY MICRO EA 1.00 I204 120-03127-0008 IC LM2903N DIP, INDUSTRIAL EA 1.00 I205 120-06025-0001 IC SCL4049ABC+ EA 1.00 I206 120-03127-0008 IC LM2903N DIP, INDUSTRIAL EA 1.00 I207 120-03127-0008 IC LM2903N DIP, INDUSTRIAL EA 1.00 P201 030-01117-0000 RECEPTACLE EA 13.00 P202 030-01117-0000 RECEPTACLE EA 19.00 Q201 007-00180-0000 XSTR S NPN 2N4401 EA 1.00 Q202 007-00180-0000 XSTR S NPN 2N4401 EA 1.00 Q203 007-00180-0000 XSTR S NPN 2N4401 EA 1.00 R201 131-00103-0013 RES CF 10K EW 5% EA 1.00 R202 131-00752-0013 RES CF 7.5K EW 5% EA 1.00 R203 131-00153-0013 RES CF 15K EW 5% EA 1.00 R204 131-00103-0013 RES CF 10K EW 5% EA 1.00 R205 131 00103 0013 RES CF 10K EW 5% EA 1 00
KFS 576A
PN DESCRIPTION REV ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------200-06580-0000 MICROPROCESSOR BD AA ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------SYMBOL PART NUMBER FIND NO DESCRIPTION UM -0000 ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------C201 111-00001-0032 CAP CR 1UF 50V EA 1.00 C202 111-00001-0013 CAP CR .1UF 50V EA 1.00 C203 111-00001-0013 CAP CR .1UF 50V EA 1.00 C204 111-00001-0077 CAP CR 12PF 100V EA 1.00 C205 111-00001-0077 CAP CR 12PF 100V EA 1.00 C206 111-00001-0077 CAP CR 12PF 100V EA 1.00 C207 111-00001-0077 CAP CR 12PF 100V EA 1.00 C208 096-01082-0015 CAP TN 2.2UF 15V EA 1.00 I201 120-02119-0000 NONVOLATILE RAM EA 1.00 I202 125-00036-0000 429 I/O MICRO EA 1.00 I203 125-00035-0001 576A DSPLY MICRO EA 1.00 I204 120-03127-0008 IC LM2903N DIP, INDUSTRIAL EA 1.00 I205 120-06025-0001 IC SCL4049ABC+ EA 1.00 I206 120-03127-0008 IC LM2903N DIP, INDUSTRIAL EA 1.00 I207 120-03127-0008 IC LM2903N DIP, INDUSTRIAL EA 1.00 P201 030-01117-0000 RECEPTACLE EA 13.00 P202 030-01117-0000 RECEPTACLE EA 19.00 Q201 007-00180-0000 XSTR S NPN 2N4401 EA 1.00 Q202 007-00180-0000 XSTR S NPN 2N4401 EA 1.00 Q203 007-00180-0000 XSTR S NPN 2N4401 EA 1.00 R201 131-00103-0013 RES CF 10K EW 5% EA 1.00 R202 131-00752-0013 RES CF 7.5K EW 5% EA 1.00 R203 131-00153-0013 RES CF 15K EW 5% EA 1.00 R204 131-00103-0013 RES CF 10K EW 5% EA 1.00 R205 131-00103-0013 RES CF 10K EW 5% EA 1.00 R206 131-00103-0013 RES CF 10K EW 5% EA 1.00 R207 131-00102-0013 RES CF 1K EW 5% EA 1.00 R208 131-00102-0013 RES CF 1K EW 5% EA 1.00 R209 131-00102-0013 RES CF 1K EW 5% EA 1.00 R210 131-00302-0013 RES CF 3K EW 5% EA 1.00 R211 131-00302-0013 RES CF 3K EW 5% EA 1.00 R212 131-00102-0013 RES CF 1K EW 5% EA 1.00 R213 131-00752-0013 RES CF 7.5K EW 5% EA 1.00 R214 131-00622-0013 RES CF 6.2K EW 5% EA 1.00 R215 131-00105-0013 RES CF 1M EW 5% EA 1.00 R216 131-00105-0013 RES CF 1M EW 5% EA 1.00 R217 131-00912-0013 RES CF 9.1K EW 5% EA 1.00 R218 131-00682-0013 RES CF 6.8K EW 5% EA 1.00 R219 131-00822-0013 RES CF 8.2K EW 5% EA 1.00 R220 131-00823-0013 RES CF 82K EW 5% EA 1.00 R221 131-00204-0013 RES CF 200K EW 5% EA 1.00 R222 131-00223-0013 RES CF 22K EW 5% EA 1.00 R223 131-00223-0013 RES CF 22K EW 5% EA 1.00 R224 131-00473-0013 RES CF 47K EW 5% EA 1.00 R225 131-00472-0013 RES CF 4.7K EW 5% EA 1.00 REF1 300-06580-0000 MICROPROCESSOR BD. RF .00 TP201 008-00096-0001 TERMINAL TEST PNT EA 1.00 TP202 008-00096-0001 TERMINAL TEST PNT EA 1.00 TP203 008-00096-0001 TERMINAL TEST PNT EA 1.00 TP204 008-00096-0001 TERMINAL TEST PNT EA 1.00 TP205 008-00096-0001 TERMINAL TEST PNT EA 1.00 TP206 008-00096-0001 TERMINAL TEST PNT EA 1.00 TP207 008-00096-0001 TERMINAL TEST PNT EA 1.00 TP208 008-00096-0001 TERMINAL TEST PNT EA 1.00 Y201 044-00128-0000 CR RSNR 11.0MHZ EA 1.00 Y202 044-00128-0000 CR RSNR 11.0MHZ EA 1.00 002-06580-0000 SCH UPROCESSOR BD RF .00 KFS 576A
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-37
KFS 576A
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------SYMBOL PART NUMBER FIND NO DESCRIPTION UM -0000 ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------009-06580-0000 PC BD UPROCESSOR EA 1.00 016-01040-0000 COATING TYPE AR AR .00 033-00092-0012 IC DIP SCKT 18C EA 1.00 033-00114-0017 SCKT IC DIP 40C EA 2.00 192-06580-0000 KFS 576A MICROPROCESSOR RF .00 BD ASSY
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-38
KFS 576A
THE FOLLOWING IS THE PARTS LIST FROM THE PREVIOUS REVISION AND IS PROVIDED FOR REFERENCE ONLY.
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-39
KFS 576A
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-40
KFS 576A
Figure 6-7 Microprocessor Board (Dwg No 300-06580-0000 Rev 4) Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-41
KFS 576A
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-42
KFS 576A
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-42
KFS 576A
Figure 6-8 Microprocessor Board (Dwg No 300-06580-0000 Rev 1) (For Reference Only) Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-43
KFS 576A
Figure 6-8 Microprocessor Board (Dwg No 300-06580-0000 Rev 1) (For Reference Only) Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-43
KFS 576A
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-44
KFS 576A
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-44
KFS 576A
Figure 6-9 Microprocessor Board Schematic (Dwg No 002-06580-0000 Rev 7) Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-45
KFS 576A
Figure 6-9 Microprocessor Board Schematic (Dwg No 002-06580-0000 Rev 7) Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-45
KFS 576A
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-46
KFS 576A
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-46
KFS 576A
Figure 6-10 Microprocessor Board Schematic (Dwg No 002-06580-0000 Rev 6) (For Reference Only) Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-47
KFS 576A
Figure 6-10 Microprocessor Board Schematic (Dwg No 002-06580-0000 Rev 6) (For Reference Only) Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-47
KFS 576A
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-48
KFS 576A
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-48
KFS 576A
PN DESCRIPTION REV ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------200-06589-0000 SW BD 28V W/SW 3 200-06589-0001 SW BD 5V W/SW 3 200-06589-0002 SW BD 28V SW 1/2 3 200-06589-0099 COMMON BM AB ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------SYMBOL PART NUMBER FIND NO DESCRIPTION UM -0000 -0001 -0002 -0099 ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------CR401 007-06016-0000 DIO S 1N4154 EA . . . 1.00 CR402 007-06016-0000 DIO S 1N4154 EA . . . 1.00 CR403 007-06016-0000 DIO S 1N4154 EA . . . 1.00 CR404 007-06016-0000 DIO S 1N4154 EA . . . 1.00 CR405 007-06016-0000 DIO S 1N4154 EA . . . 1.00 CR406 007-06016-0000 DIO S 1N4154 EA . . . 1.00 CR407 007-06016-0000 DIO S 1N4154 EA . . . 1.00 CR408 007-06016-0000 DIO S 1N4154 EA . . . 1.00 DS401 037-00034-0000 LMP 7715 T1 5V EA . 1.00 . . DS401 037-00034-0001 LMP 7839 T1 28V EA 1.00 . 1.00 . DS402 037-00034-0000 LMP 7715 T1 5V EA . 1.00 . . DS402 037-00034-0001 LMP 7839 T1 28V EA 1.00 . 1.00 . P402 030-02200-0008 VERT CRD CONN 8P EA . . . 1.00 P404 030-02200-0008 VERT CRD CONN 8P EA . . . 2.00 R401 131-00334-0013 RES CF 330K EW 5% EA . . . 1.00 R402 131-00334-0013 RES CF 330K EW 5% EA . . . 1.00 R403 131-00334-0013 RES CF 330K EW 5% EA . . . 1.00 R404 131-00334-0013 RES CF 330K EW 5% EA . . . 1.00 REF1 300-06589-0000 SWITCH BD KFS 576A RF .00 .00 .00 . S401 031-00443-0001 SW ROTARY AJ-20 EA . . 1.00 . S401 031-00443-0003 SWITCH 2P EA 1.00 1.00 . . S402 031 00372 0001 SWITCH SLIDE SPDT EA 1 00
KFS 576A
PN DESCRIPTION REV ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------200-06589-0000 SW BD 28V W/SW 3 200-06589-0001 SW BD 5V W/SW 3 200-06589-0002 SW BD 28V SW 1/2 3 200-06589-0099 COMMON BM AB ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------SYMBOL PART NUMBER FIND NO DESCRIPTION UM -0000 -0001 -0002 -0099 ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------CR401 007-06016-0000 DIO S 1N4154 EA . . . 1.00 CR402 007-06016-0000 DIO S 1N4154 EA . . . 1.00 CR403 007-06016-0000 DIO S 1N4154 EA . . . 1.00 CR404 007-06016-0000 DIO S 1N4154 EA . . . 1.00 CR405 007-06016-0000 DIO S 1N4154 EA . . . 1.00 CR406 007-06016-0000 DIO S 1N4154 EA . . . 1.00 CR407 007-06016-0000 DIO S 1N4154 EA . . . 1.00 CR408 007-06016-0000 DIO S 1N4154 EA . . . 1.00 DS401 037-00034-0000 LMP 7715 T1 5V EA . 1.00 . . DS401 037-00034-0001 LMP 7839 T1 28V EA 1.00 . 1.00 . DS402 037-00034-0000 LMP 7715 T1 5V EA . 1.00 . . DS402 037-00034-0001 LMP 7839 T1 28V EA 1.00 . 1.00 . P402 030-02200-0008 VERT CRD CONN 8P EA . . . 1.00 P404 030-02200-0008 VERT CRD CONN 8P EA . . . 2.00 R401 131-00334-0013 RES CF 330K EW 5% EA . . . 1.00 R402 131-00334-0013 RES CF 330K EW 5% EA . . . 1.00 R403 131-00334-0013 RES CF 330K EW 5% EA . . . 1.00 R404 131-00334-0013 RES CF 330K EW 5% EA . . . 1.00 REF1 300-06589-0000 SWITCH BD KFS 576A RF .00 .00 .00 . S401 031-00443-0001 SW ROTARY AJ-20 EA . . 1.00 . S401 031-00443-0003 SWITCH 2P EA 1.00 1.00 . . S402 031-00372-0001 SWITCH SLIDE SPDT EA . . . 1.00 S403 031-00399-0002 SWITCH ASSY IDT EA . . . 1.00 V401 134-05005-0000 PHOTODETECTOR EA . . . 1.00 009-06589-0000 PC BD SWITCH EA . . . 1.00 012-01299-0000 INSULATING WASHER EA . . . 1.00 016-01013-0000 VAC GREASE DC 976 AR . . . .00 016-01040-0000 COATING TYPE AR AR . . . .00 025-00018-0099 WIRE 26 WHT IN . . . 7.20 030-01185-0000 CONNECTOR SOCKET EA . . . 25.00 047-05798-0000 DETENT SPRING .030 EA . . . 1.00 047-05798-0001 DETENT SPRING .025 EA . . . 1.00 047-06689-0002 BRACKET ASSEMBLED EA . . . 1.00 073-00505-0002 BRACKET EA . . . 1.00 073-00550-0002 SHAFT W/F EA . . . 1.00 076-01232-0003 SHAFT W/F EA . . . 1.00 076-01433-0001 SPOOL W/F EA . . . 1.00 078-00116-0000 SPRING COMPRESSION EA . . . 1.00 088-00769-0000 SLEEVE LOCKING EA . . . 1.00 088-00971-0000 SPCR PHOTODETECTOR EA . . . 1.00 088-01022-0001 CONTACT ASSY EA . . . 2.00 088-01053-0000 SWITCH HOUSING EA . . . 1.00 088-01084-0000 SWITCH HOUSING EA . . . 1.00 089-02136-0000 NUT LOCK 2-56 EA . . . 2.00 089-05899-0011 SCR PHP 2-56X11/16 EA . . . 2.00 089-06004-0003 SCR FHP 2-56X3/16 EA . . . 3.00 089-08023-0030 WSHR FLT STD #2 EA . . . 1.00 090-00019-0005 RING RTNR .188 EA . . . 2.00 090-00036-0004 RING RTNR .051 EA . . . 1.00 092-05009-0004 RVT BH 1/16X.125 EA . . . 2.00 155-02169-0000 CABLE ASSY SW BD EA . . . 1.00 200-06589-0099 COMMON BM EA 1.00 1.00 1.00 .
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-49
KFS 576A
PN DESCRIPTION REV ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------200-06589-0003 SW BD 5V SW 1/2 3 200-06589-0004 SW BD 28V NO SW 4 200-06589-0005 SW BD 5V NO SW AA 200-06589-0099 COMMON BM AB ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------SYMBOL PART NUMBER FIND NO DESCRIPTION UM -0003 -0004 -0005 -0099 ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------CJ1 026-00030-0000 WIRE, CU, 24AWG, TINNED IN . . 1.00 . CR401 007-06016-0000 DIO S 1N4154 EA . . . 1.00 CR402 007-06016-0000 DIO S 1N4154 EA . . . 1.00 CR403 007-06016-0000 DIO S 1N4154 EA . . . 1.00 CR404 007-06016-0000 DIO S 1N4154 EA . . . 1.00 CR405 007-06016-0000 DIO S 1N4154 EA . . . 1.00 CR406 007-06016-0000 DIO S 1N4154 EA . . . 1.00 CR407 007-06016-0000 DIO S 1N4154 EA . . . 1.00 CR408 007-06016-0000 DIO S 1N4154 EA . . . 1.00 DS401 037-00034-0000 LMP 7715 T1 5V EA 1.00 . 1.00 . DS401 037-00034-0001 LMP 7839 T1 28V EA . 1.00 . . DS402 037-00034-0000 LMP 7715 T1 5V EA 1.00 . 1.00 . DS402 037-00034-0001 LMP 7839 T1 28V EA . 1.00 . . P402 030-02200-0008 VERT CRD CONN 8P EA . . . 1.00 P404 030-02200-0008 VERT CRD CONN 8P EA . . . 2.00 R401 131-00334-0013 RES CF 330K EW 5% EA . . . 1.00 R402 131-00334-0013 RES CF 330K EW 5% EA . . . 1.00 R403 131-00334-0013 RES CF 330K EW 5% EA . . . 1.00 R404 131-00334-0013 RES CF 330K EW 5% EA . . . 1.00 REF1 300-06589-0000 SWITCH BD KFS 576A RF .00 .00 .00 . S401 031-00443-0001 SW ROTARY AJ-20 EA 1.00 . . . S402 031-00372-0001 SWITCH SLIDE SPDT EA . . . 1.00 S403 031-00399-0002 SWITCH ASSY IDT EA . . . 1.00 V401 134-05005-0000 PHOTODETECTOR EA . . . 1.00 009-06589-0000 PC BD SWITCH EA . . . 1.00 012-01299-0000 INSULATING WASHER EA . . . 1.00 016-01013-0000 VAC GREASE DC 976 AR . . . .00 016-01040-0000 COATING TYPE AR AR . . . .00 025-00018-0099 WIRE 26 WHT IN . . . 7.20 026-00030-0000 WIRE, CU, 24AWG, TINNED IN . 1.00 . . 030-01185-0000 CONNECTOR SOCKET EA . . . 25.00 047-05798-0000 DETENT SPRING .030 EA . . . 1.00 047-05798-0001 DETENT SPRING .025 EA . . . 1.00 047-06689-0002 BRACKET ASSEMBLED EA . . . 1.00 073-00505-0002 BRACKET EA . . . 1.00 073-00550-0002 SHAFT W/F EA . . . 1.00 076-01232-0003 SHAFT W/F EA . . . 1.00 076-01433-0001 SPOOL W/F EA . . . 1.00 078-00116-0000 SPRING COMPRESSION EA . . . 1.00 088-00769-0000 SLEEVE LOCKING EA . . . 1.00 088-00971-0000 SPCR PHOTODETECTOR EA . . . 1.00 088-01022-0001 CONTACT ASSY EA . . . 2.00 088-01053-0000 SWITCH HOUSING EA . . . 1.00 088-01084-0000 SWITCH HOUSING EA . . . 1.00 089-02136-0000 NUT LOCK 2-56 EA . . . 2.00 089-05899-0011 SCR PHP 2-56X11/16 EA . . . 2.00 089-06004-0003 SCR FHP 2-56X3/16 EA . . . 3.00 089-08023-0030 WSHR FLT STD #2 EA . . . 1.00 090-00019-0005 RING RTNR .188 EA . . . 2.00 090-00036-0004 RING RTNR .051 EA . . . 1.00 092-05009-0004 RVT BH 1/16X.125 EA . . . 2.00 155-02169-0000 CABLE ASSY SW BD EA . . . 1.00 200-06589-0099 COMMON BM EA 1.00 1.00 1.00 .
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-50
KFS 576A
PN DESCRIPTION REV ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------200-06589-0006 SW BD 28V 1/2 3 200-06589-0007 SW BD 5V 1/2 1 200-06589-0099 COMMON BM AB ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------SYMBOL PART NUMBER FIND NO DESCRIPTION UM -0006 -0007 -0099 ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------CR401 007-06016-0000 DIO S 1N4154 EA . . 1.00 CR402 007-06016-0000 DIO S 1N4154 EA . . 1.00 CR403 007-06016-0000 DIO S 1N4154 EA . . 1.00 CR404 007-06016-0000 DIO S 1N4154 EA . . 1.00 CR405 007-06016-0000 DIO S 1N4154 EA . . 1.00 CR406 007-06016-0000 DIO S 1N4154 EA . . 1.00 CR407 007-06016-0000 DIO S 1N4154 EA . . 1.00 CR408 007-06016-0000 DIO S 1N4154 EA . . 1.00 DS401 037-00034-0000 LMP 7715 T1 5V EA . 1.00 . DS401 037-00034-0001 LMP 7839 T1 28V EA 1.00 . . DS402 037-00034-0000 LMP 7715 T1 5V EA . 1.00 . DS402 037-00034-0001 LMP 7839 T1 28V EA 1.00 . . P402 030-02200-0008 VERT CRD CONN 8P EA . . 1.00 P404 030-02200-0008 VERT CRD CONN 8P EA . . 2.00 R401 131-00334-0013 RES CF 330K EW 5% EA . . 1.00 R402 131-00334-0013 RES CF 330K EW 5% EA . . 1.00 R403 131-00334-0013 RES CF 330K EW 5% EA . . 1.00 R404 131-00334-0013 RES CF 330K EW 5% EA . . 1.00 REF1 300-06589-0000 SWITCH BD KFS 576A RF .00 .00 . S401 031-00443-0002 SW ROTARY AJ-7 EA 1.00 1.00 . S402 031-00372-0001 SWITCH SLIDE SPDT EA . . 1.00 S403 031-00399-0002 SWITCH ASSY IDT EA . . 1.00 V401 134-05005-0000 PHOTODETECTOR EA . . 1.00 009-06589-0000 PC BD SWITCH EA . . 1.00 012-01299-0000 INSULATING WASHER EA . . 1.00 016-01013-0000 VAC GREASE DC 976 AR . . .00 016-01040-0000 COATING TYPE AR AR . . .00 025-00018-0099 WIRE 26 WHT IN . . 7.20 030-01185-0000 CONNECTOR SOCKET EA . . 25.00 047-05798-0000 DETENT SPRING .030 EA . . 1.00 047-05798-0001 DETENT SPRING .025 EA . . 1.00 047-06689-0002 BRACKET ASSEMBLED EA . . 1.00 073-00505-0002 BRACKET EA . . 1.00 073-00550-0002 SHAFT W/F EA . . 1.00 076-01232-0003 SHAFT W/F EA . . 1.00 076-01433-0001 SPOOL W/F EA . . 1.00 078-00116-0000 SPRING COMPRESSION EA . . 1.00 088-00769-0000 SLEEVE LOCKING EA . . 1.00 088-00971-0000 SPCR PHOTODETECTOR EA . . 1.00 088-01022-0001 CONTACT ASSY EA . . 2.00 088-01053-0000 SWITCH HOUSING EA . . 1.00 088-01084-0000 SWITCH HOUSING EA . . 1.00 089-02136-0000 NUT LOCK 2-56 EA . . 2.00 089-05899-0011 SCR PHP 2-56X11/16 EA . . 2.00 089-06004-0003 SCR FHP 2-56X3/16 EA . . 3.00 089-08023-0030 WSHR FLT STD #2 EA . . 1.00 090-00019-0005 RING RTNR .188 EA . . 2.00 090-00036-0004 RING RTNR .051 EA . . 1.00 092-05009-0004 RVT BH 1/16X.125 EA . . 2.00 155-02169-0000 CABLE ASSY SW BD EA . . 1.00 200-06589-0099 COMMON BM EA 1.00 1.00 .
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-51
KFS 576A
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-52
KFS 576A
THE FOLLOWING IS THE PARTS LIST FROM THE PREVIOUS REVISION AND IS PROVIDED FOR REFERENCE ONLY.
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-53
KFS 576A
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-54
KFS 576A
Figure 6-11 Switch Board (Dwg No 300-06589-0000 Rev AC) Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-55
KFS 576A
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-56
KFS 576A
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-56
KFS 576A
Figure 6-12 Switch Board (Dwg No 300-06589-0000 Rev 5) (For Reference Only) Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-57
KFS 576A
Figure 6-12 Switch Board (Dwg No 300-06589-0000 Rev 5) (For Reference Only) Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-57
KFS 576A
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-58
KFS 576A
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-58
KFS 576A
Figure 6-13 Switch Board Schematic (Dwg No 002-06589-0000 Rev 1) Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-59
KFS 576A
Figure 6-13 Switch Board Schematic (Dwg No 002-06589-0000 Rev 1) Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-59
KFS 576A
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-60
KFS 576A
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-60
KFS 576A
PN DESCRIPTION REV ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------200-06626-0000 DRIVER BD AA ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------SYMBOL PART NUMBER FIND NO DESCRIPTION UM -0000 ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------C302 113-05331-0000 CAP DC 330PF 500V EA 1.00 C303 113-05331-0000 CAP DC 330PF 500V EA 1.00 C304 111-02104-0041 CAP MC 100KPF50V10 EA 1.00 C305 097-00103-0020 CAP AL 1.0UF 350V EA 1.00 C306 111-00001-0063 CAP CR .022UF 200V EA 1.00 C307 096-01006-0000 CAP TN 1.0UF 50V EA 1.00 C308 111-02103-0041 CAP MC 10KPF50V10% EA 1.00 C309 999-09999-0098 PLACE HOLDER RF .00 C310 096-01082-0009 CAP TN 15UF 20V EA 1.00 C311 096-01009-0000 CAP TN 22UF 15V EA 1.00 CR301 007-06111-0000 DIO S IN4157 EA 1.00 CR302 007-06016-0000 DIO S 1N4154 EA 1.00 CR303 007-06111-0000 DIO S IN4157 EA 1.00 CR304 007-06059-0000 DIO S FDH400 EA 1.00 CR305 007-06059-0000 DIO S FDH400 EA 1.00 I301 120-00163-0000 IC DI8884A EA 1.00 I302 120-00161-0000 HIGH VOLT DSPLY DR EA 1.00 I303 120-03138-0000 IC DI 240A EA 1.00 I304 120-06045-0001 IC SCL4022ABC+ EA 1.00 I305 120-03040-0000 IC SE555CN EA 1.00 I306 120-03053-0000 IC LM358N EA 1.00 I307 120-03025-0004 IC LM209H EA 1.00 J302 030-02217-0005 HEADER RTANG 8P EA 1.00 J304 030-02424-0002 HDR RTANG DBL 16P EA 1.00 P301 030 01117 0000 RECEPTACLE EA 14 00
KFS 576A
PN DESCRIPTION REV ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------200-06626-0000 DRIVER BD AA ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------SYMBOL PART NUMBER FIND NO DESCRIPTION UM -0000 ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------C302 113-05331-0000 CAP DC 330PF 500V EA 1.00 C303 113-05331-0000 CAP DC 330PF 500V EA 1.00 C304 111-02104-0041 CAP MC 100KPF50V10 EA 1.00 C305 097-00103-0020 CAP AL 1.0UF 350V EA 1.00 C306 111-00001-0063 CAP CR .022UF 200V EA 1.00 C307 096-01006-0000 CAP TN 1.0UF 50V EA 1.00 C308 111-02103-0041 CAP MC 10KPF50V10% EA 1.00 C309 999-09999-0098 PLACE HOLDER RF .00 C310 096-01082-0009 CAP TN 15UF 20V EA 1.00 C311 096-01009-0000 CAP TN 22UF 15V EA 1.00 CR301 007-06111-0000 DIO S IN4157 EA 1.00 CR302 007-06016-0000 DIO S 1N4154 EA 1.00 CR303 007-06111-0000 DIO S IN4157 EA 1.00 CR304 007-06059-0000 DIO S FDH400 EA 1.00 CR305 007-06059-0000 DIO S FDH400 EA 1.00 I301 120-00163-0000 IC DI8884A EA 1.00 I302 120-00161-0000 HIGH VOLT DSPLY DR EA 1.00 I303 120-03138-0000 IC DI 240A EA 1.00 I304 120-06045-0001 IC SCL4022ABC+ EA 1.00 I305 120-03040-0000 IC SE555CN EA 1.00 I306 120-03053-0000 IC LM358N EA 1.00 I307 120-03025-0004 IC LM209H EA 1.00 J302 030-02217-0005 HEADER RTANG 8P EA 1.00 J304 030-02424-0002 HDR RTANG DBL 16P EA 1.00 P301 030-01117-0000 RECEPTACLE EA 14.00 Q301 007-00383-0001 XSTR S NPN 2N2222A EA 1.00 (TO-18 PACKAGE) Q302 007-00383-0001 XSTR S NPN 2N2222A EA 1.00 (TO-18 PACKAGE) Q303 007-00409-0003 XSTR S MM5416 EA 1.00 Q304 007-00409-0000 XSTR S 2N3439 EA 1.00 Q305 007-00409-0003 XSTR S MM5416 EA 1.00 Q306 007-00383-0001 XSTR S NPN 2N2222A EA 1.00 (TO-18 PACKAGE) R301 131-00103-0013 RES CF 10K EW 5% EA 1.00 R302 131-00103-0013 RES CF 10K EW 5% EA 1.00 R303 131-00105-0013 RES CF 1M EW 5% EA 1.00 R304 131-00105-0013 RES CF 1M EW 5% EA 1.00 R305 131-00822-0013 RES CF 8.2K EW 5% EA 1.00 R306 999-09999-0098 PLACE HOLDER RF .00 R307 999-09999-0098 PLACE HOLDER RF .00 R308 131-00912-0013 RES CF 9.1K EW 5% EA 1.00 R309 131-00823-0013 RES CF 82K EW 5% EA 1.00 R310 131-00240-0013 RES CF 24 EW 5% EA 1.00 R311 131-00334-0013 RES CF 330K EW 5% EA 1.00 R312 131-00104-0013 RES CF 100K EW 5% EA 1.00 R313 131-00753-0013 RES CF 75K EW 5% EA 1.00 R314 131-00683-0013 RES CF 68K EW 5% EA 1.00 R315 131-00333-0013 RES CF 33K EW 5% EA 1.00 R316 131-00204-0013 RES CF 200K EW 5% EA 1.00 R317 131-00683-0013 RES CF 68K EW 5% EA 1.00 R318 131-00432-0013 RES CF 4.3K EW 5% EA 1.00 R319 131-00683-0013 RES CF 68K EW 5% EA 1.00 R320 131-00204-0013 RES CF 200K EW 5% EA 1.00 R321 131-00154-0013 RES CF 150K EW 5% EA 1.00 R322 131-00394-0013 RES CF 390K EW 5% EA 1.00 R323 131-00202-0013 RES CF 2K EW 5% EA 1.00 R324 131-00154-0013 RES CF 150K EW 5% EA 1.00
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-61
KFS 576A
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------SYMBOL PART NUMBER FIND NO DESCRIPTION UM -0000 ------------------------------------------------------------------------------------------------------------------------------------------------------------------------------R325 131-00394-0013 RES CF 390K EW 5% EA 1.00 R326 131-00512-0013 RES CF 5.1K EW 5% EA 1.00 R327 133-00122-0001 RES VA 2K HW 20% EA 1.00 R328 131-00105-0013 RES CF 1M EW 5% EA 1.00 R329 131-00105-0013 RES CF 1M EW 5% EA 1.00 R330 131-00823-0013 RES CF 82K EW 5% EA 1.00 R331 131-00103-0013 RES CF 10K EW 5% EA 1.00 REF1 300-06626-0000 DRIVER BD ASSY RF .00 REF2 002-06626-0000 SCH DRIVER BOARD KFS 576 RF .00 TP301 008-00096-0001 TERMINAL TEST PNT EA 1.00 TP302 008-00096-0001 TERMINAL TEST PNT EA 1.00 TP303 008-00096-0001 TERMINAL TEST PNT EA 1.00 TP304 008-00096-0001 TERMINAL TEST PNT EA 1.00 U301 015-00055-0001 NTWK RES 1M10%.125 EA 1.00 009-06626-0000 PC BD DRIVER EA 1.00 016-01040-0000 COATING TYPE AR AR .00 033-00092-0011 IC DIP SCKT 16C EA 1.00 033-00092-0012 IC DIP SCKT 18C EA 3.00 090-00307-0000 HEAT SINK FOR TO-5 EA 1.00 091-00025-0000 WSHR XSTR INSUL EA 2.00 091-00182-0000 CAP SEMICN TO-5 EA 2.00 192-06626-0000 KFS 576A DRIVER BOARD RF .00 ASSY
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-62
KFS 576A
THE FOLLOWING IS THE PARTS LIST FROM THE PREVIOUS REVISION AND IS PROVIDED FOR REFERENCE ONLY.
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-63
KFS 576A
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-64
KFS 576A
Figure 6-14 Driver Board (Dwg No 300-06626-0000 Rev 4) Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-65
KFS 576A
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-66
KFS 576A
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-66
KFS 576A
Figure 6-15 Driver Board (Dwg No 300-06626-0000 Rev 2) (For Reference Only) Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-67
KFS 576A
Figure 6-15 Driver Board (Dwg No 300-06626-0000 Rev 2) (For Reference Only) Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-67
KFS 576A
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-68
KFS 576A
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-68
KFS 576A
Figure 6-16 Driver Board Schematic (Dwg No 002-06626-0000 Rev 1) Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-69
KFS 576A
Figure 6-16 Driver Board Schematic (Dwg No 002-06626-0000 Rev 1) Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-69
KFS 576A
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-70
KFS 576A
Rev 0, Apr/2007
©Honeywell International Inc. Do not print without express permission of Honeywell.
6-70
THE END
THE END