COMPLETE REVISION
PIP PNSMV005 Carbon Steel Check Valve Descriptions
March 2010
Description of CHECK Valve (CS03CA501): Type:............................. CHECK Valve Size:....................... NPS 26 -to- NPS 48 Class:............................ 300 Ends:............................. FLANGED RF Body:............................. ITCS (ASTM A352 - LCB or A352 - LCC) Cover/Bonnet:..................... ITCS (ASTM A352 - LCB or A352 - LCC) Trim:............................. 316 SS, API 600 TRIM 12 Hard Facing:...................... HALF Design Type:...................... SWING Cover/Bonnet Type:................ BOLTED Body-Bonnet Gaskets:.............. API 600 Body-Bonnet Bolting:.............. BOLTS: ASTM A320 - L7 NUTS: ASTM A194 - 4 Installation:..................... HORIZONTAL - COVER UP or VERTICAL - UPWARD FLOW The standards are: DESIGN ENDS RATING TESTING DIMENSIONAL
-
API 600, as applicable ASME B16.47 SERIES B ASME B16.34 API 598 ASME B16.10 (NPS 26 -to- NPS 36) MFG STD (NPS 38 -to- NPS 48)
Description of CHECK Valve (CS03CB500): Type:............................. CHECK Valve Size:....................... NPS 2 -to- NPS 24 Class:............................ 300 Ends:............................. FLANGED RF Body:............................. CS (ASTM A216 - WCB) Cover/Bonnet:..................... CS (ASTM A216 - WCB) Trim:............................. 13 CR, API 600 TRIM 8 Hard Facing:...................... HALF Design Type:...................... SWING Cover/Bonnet Type:................ BOLTED Body-Bonnet Gaskets:.............. API 600 Body-Bonnet Bolting:.............. BOLTS: ASTM A193 - B7 NUTS: ASTM A194 - 2H Installation:..................... HORIZONTAL - COVER UP or VERTICAL - UPWARD FLOW The standards are: DESIGN ENDS RATING TESTING DIMENSIONAL
` , , ` ` , , ` , , ` , , , , , ` ` , ` ` , ` ` , ` ` ` , ` ` ` , , ` , , ` , ` , , ` -
-
API 600, as applicable ASME B16.5 ASME B16.34 API 598 ASME B16.10
Description of CHECK Valve (CS03CB501): Type:............................. CHECK Valve Size:....................... NPS 26 -to- NPS 48 Class:............................ 300 Ends:............................. FLANGED RF Body:............................. CS (ASTM A216 - WCB) Cover/Bonnet:..................... CS (ASTM A216 - WCB) Trim:............................. 13 CR, API 600 TRIM 8 Hard Facing:...................... HALF Design Type:...................... SWING Cover/Bonnet Type:................ BOLTED Body-Bonnet Gaskets:.............. API 600 Body-Bonnet Bolting:.............. BOLTS: ASTM A193 - B7 NUTS: ASTM A194 - 2H Installation:..................... HORIZONTAL - COVER UP or VERTICAL - UPWARD FLOW The standards are: DESIGN ENDS RATING TESTING DIMENSIONAL
-
API 600, as applicable ASME B16.47 SERIES B ASME B16.34 API 598 ASME B16.10 (NPS 26 -to- NPS 36) MFG STD (NPS 38 -to- NPS 48)
Process Industry Practices Copyright Process Industry Practices Provided by IHS under license with PIP No reproduction or networking permitted without license from I HS
Page 19 of 23 Licensee=Jacobs ASTM & PIP Only/3219500105 Not for Resale, 06/25/2012 13:29:27 MDT
PURPOSE AND USE OF PROCESS INDUSTRY PRACTICES In an effort to minimize the cost of process industry facilities, this Practice has been prepared from the technical technical requirements in the existing standards of major industrial users, contractors, or standards organizations. By harmonizing these technical requirements into a single set of Practices, administrative, application, and engineering costs to both the purchaser and the manufacturer should be reduced. While this Practice is expected to incorporate the majority of requirements of most users, individual applications may involve requirements that will be appended to and take precedence over this Practice. Determinations concerning fitness for purpose and particular matters matters or application application of of the Practice Practice to particular particular project project or engineering engineering situations situations should should not be made solely on information contained in these materials. The use of trade names from time to time should not be viewed as an expression of preference but rather recognized as normal usage in the trade. Other brands having the same specifications are equally correct and may be substituted for those named. All Practices or guidelines are intended to be consistent with applicable laws and regulations including OSHA requirements. To the extent these Practices or guidelines should conflict with OSHA or other applicable laws or regulations, such laws or regulations must be followed. Consult an appropriate professional before applying or acting on any material contained in or suggested by the Practice.
This Practice is subject to revision at any time.
© Process Industry Practices (PIP), Construction Industry Institute, The University of Texas at Austin, 3925 West Braker Lane (R4500), Austin, Texas 78759. PIP Member Companies and Subscribers may copy this Practice for their internal use. Changes or modifications of any kind are not permitted permitted within within any PIP PIP Practice Practice withou withoutt the express express written written authoriz authorization ation of of PIP. Authorize Authorized d Users may attach addenda or overlays to clearly indicate modifications or exceptions to specific sections of PIP Practices. Authorized Users may provide their clients, suppliers and contractors with copies of the Practice solely for Authorized Users’ pu rposes. These purposes include but are not limited limited to the procureme procurement nt process process (e.g., as attachme attachments nts to requests requests for quotation/ quotation/ purchase purchase orders or requests requests for proposals/c proposals/contra ontracts) cts) and and preparati preparation on and and issue issue of design design engineeri engineering ng deliver deliverables ables for use on a specific specific project project by Authorize Authorized d User’s client. client. PIP’s PIP’s copyright copyright notices notices must be clearly clearly indicated indicated and unequivocally incorporated in documents where an Authorized User desires to provide any t hird party with copies of the Practice.