En esta práctica de laboratorio, examinará el exterior del router para familiarizarse con las características y componentes de este, como el interruptor de alimentación, los puertos de admin…Descripción completa
chemistry form 4 preparing standard solutionFull description
Full description
Descripción completa
Deskripsi lengkap
Manual que te permite fabricar tu propio router para madera cnc.
routerDescripción completa
Descripción completa
Router MagicFull description
Full description
Descripción: Pack de Guias Practicas para ejercitarte en el mundo de las Redes.
Router esim Solution Lab_A
Here are the commands you enter to program Router A in the Esim…don’t type lines starting with *…those are just explanations I have put in for you !elow the explanation set is another copy without all the comments…much easier to use after you have done the reading part "nce you have programmed la# A go on and program the others in the $I% &ou should #e a#le to program the entire E'$im in under () minutes minutes once you get used to it Ena *Ena#le the router for programming +onfig t *+onfigure in terminal mode…li,e a one line -"$ mode Hostname .a#/A *0he name your are giving the router Ena#le secret class *0o get into the router next time you need to ,now the secret password…class password…class *1sing the word 2secret3 means the password will #e encrypted so people can’t see it on future output .ine con ) *&ou want to program the +onsole port…this is a physical port on the router…used normally to plug in a computer to program the router for initial setup 4assword cisco *to get in through the +onsole port you will #e as,ed next time for the password which is 2cisco3 2cisco3 .ogin *tells the router the person must .ogin to get in through the +onsole .ine vty ) 5 *there are 6 telnet lines 7vty lines8 )9:9(9; and 5…these are for connecting to the router over the internet using 0elnet *each of these lines could #e individually password protected instead of them all having the same password 4assword cisco *to get into the vty lines you now need a password .ogin *and you have to log in to get in through the vty lines Exit *exit out of the programming the vty lines Int e) *go into interface Ethernet ) 0hese Ethernet outlets usually connect to the .A<
Ip add :=(66: (66(66(66) *give it an ip address and a su#net mas, 7standard class + in this case8 6: (66(66(66) *ip and su#net for Ethernet : 6) *@e want our router to advertise to other routers that we have the ()6>6) networ, attached 6: ()::)):::
Ip host .a#/! (:=:>:)): :==?:;: ()::))::( Ip host .a#/+ ((;:6:: ()5()5>: :==?:;( Ip host .a#/- (:)=;:)6: ()5()5>( Ip host .a#/E (:)=;:)6( Exit *exit this mode Exit *exit this mode +opy run start *save the program we just wrote into the
Ena +onfig t Hostname .a#/A Ena#le secret class .ine con ) 4assword cisco .ogin .ine vty ) 5 4assword cisco .ogin Exit Int e) Ip add :=(66: (66(66(66) 6: (66(66(66) 6) 6: ()::))::: Ip host .a#/! (:=:>:)): :==?:;: ()::))::( Ip host .a#/+ ((;:6:: ()5()5>: :==?:;( Ip host .a#/- (:)=;:)6: ()5()5>(
Ip host .a#/E (:)=;:)6( Exit Exit +opy run start