Contoh Perhitungan Menggunakan Software ETABSFull description
Contoh Perhitungan Menggunakan Software ETABS
Boundary Element Method for FEA design
BOQ for boundary wall and officeFull description
Boundary wall
Full description
Full description
Full description
APA Shear WallFull description
Sistem struktur shear wall ( dinding geser )
Design of shear walls
Full description
Design of shear wall as per ACi method
Hand Calculation of Coupled Shear Wall
Descripción: Shear Wall Design Note
Bar Bending ScheduleFull description
shear
Design of shear walls
DINDING GESER UNTUK BANGUNAN BERTINGKAT BANYAK
Structural Design Calculation
SHEAR WALL BOUNDARY ELEMENT (AS PER ACI318M-11)
Published by: E.G Navarro CE- Mindanao University of Science and Technology 20-May-14
1
Structural Design Calculation DESIGN OF BOUNDARY ELEMENT PARAMETERS fc' = fy = Lw = b= C= Mu = Vu = cc = d= dhoop =
32.0 MPa 460.0 MPa 3000.0 mm 300.0 mm 502.0 mm 2700.0 KN-m 450.0 KN 30 mm 16 mm 10 mm
(concrete compressive stregth) (yeild strength of reinforcement) ( length of wall) (thickness of wall) (neutral axis depth from etabs) (ultimate moment from etabs) (ultimate shear from etabs) (clear concrete cover) (size of vertical bars) (size of boundary ties/hoop)
BOUNDARY ELEMENT CHECK ( STRESS BASE) Stress Compression Left top Right top Left bot Right bot
= = = =
1555.56 1555.56 7765.56 7765.56
( ACI 21.9.6.3 ) Stress Limit
< < > >
= = = =
not required! not required! boundary element required! boundary element required!
6400.00 6400.00 6400.00 6400.00
1
Structural Design Calculation HEIGHT OF BOUNDARY ELEMENT ( Hb)
( ACI 21.9.6.2b )
The special boundary element reinforcement must extend vertically from the critical section a distance not less than the larger of Lw or Mu/4Vu. Lw = 3000.0 mm Mu/4Vu = 2,700.0 / 4 x 450.0 = 1500.0 mm
boundary element
Hb
Hb = 3000.0 mm
LENGTH OF BOUNDARY ELEMENT ( Lb)
( ACI318-11, section 21.9.6.4a )
The special boundary element reinforcement must extend horizontally from the extreme compression fiber a distance not less than the larger C-0.1Lw or C/2. C-0.1Lw = 502.0 - 0.1 x 3,000.0 = 202.0 mm C/2 = 502.0 / 2 = 251.0 mm Lb = 251.0 mm Lbprovided = 300.0 mm
(boundary element length provided)
HOOP REINFORCEMENT (Ash)
( ACI318-11, section 21.6.6.4b )
Lbprovided Ash = 0.09.S. bc. fc'/fy S = 200.0 mm bc = 188.0 mm
(spacing of hoops) (as per figure)
b
Hoop minimum reinforcement equals to maximum of ( Ash1 or Ash2) Ash1 = 0.3.S. bc. fc'/fy ( Ag/Ach -1) = 0.3x200.0 x 188.0 x 32.0 / 460.0 (( 900,000.0 / 705,600.0- 1)) = 216.2 mm² Ag = 900000.00 mm² Ach = 705600.00 mm²
bc
(gross area of concrete section) (cross section area of concrete measured from outside of transverse reinforcement)
Ash2 = 0.09.S. bc. fc'/fy = 0.09x200.0 x 188.0 x 32.0 / 460.0 = 235.4 mm² Using Ash provided = 235.62 mm²
T10
@
200mm c/c >
3 LEGS 235.41 mm²
2
OK!
Structural Design Calculation BOUNDARY ELEMENT DETAIL 300.0 mm