pharmaceutical factory design, working styles,problem solving , qc,qa, maintenance,
Site Master File
Mastering Paint.NetFull description
USBN BK
Descripción completa
masterFull description
SITELESS - 1001 Building forms
ReferenceDescription complète
site analysis
Site Instruction
ReferenceDescripción completa
qcFull description
masterDescription complète
Full description
qcDescription complète
hbhjbnjmFull description
SITELESS - 1001 Building formsFull description
site planeFull description
SITELESS - 1001 Building formsDescrição completa
site
architectureFull description
SITE MASTER INNO DS8000B
Created by: Engr Russell Salazar FM Engineer Mobily 3G Project
SETTING THE LANGUAGE Choose the Language from pop up Click the Instrument Settings soft key. Select Press Restart Enter. language the device. soft key. the System key. menu. Use Up/Down Key.
Enter
Chinese
Created by: Engr Russell Salazar FM Engineer Mobily 3G Project
DTF ( DISTANCE TO FAULT) MODE PROCEDURE: o o o o o o
o o
Enter the Start and Stop Frequency or choose the Band from Band List key. Choose which type of cable is used. Click Cable List menu. Calibrate the device. Set the total distance i.e. from NodeB to Antenna port (length of Jumper Cables–indoor and outdoor, and Feeder Cable) Set the Max and Minimum Amplitude, click Amplitude (1) soft key. Set the Marker (4) . Marker 1 (indoor jumper), Marker2 (Feeder), Marker3 (outdoor Jumper) Press Hold (+/-) button to start the measurement. Press Peak (6) button to see the maximum value of your measurement and see the corresponding distance from your marker.
Created by: Engr Russell Salazar FM Engineer Mobily 3G Project
DTF MODE FREQUENCY BAND Enter the Start and Stop Frequency or choose the Band from Band List key.
Created by: Engr Russell Salazar FM Engineer Mobily 3G Project
DTF MODE CABLE TYPE Choose which type of cable is used. Click Cable List menu.
Created by: Engr Russell Salazar FM Engineer Mobily 3G Project
DTF MODE CALIBRATE: OPEN Calibrate the device. Press Cal button key.
Connect OPEN to RF port and then press continue. Created by: Engr Russell Salazar FM Engineer Mobily 3G Project
DTF MODE CALIBRATE: SHORT
If OPEN calibration is completed, Connect SHORT to RF port and then press continue Created by: Engr Russell Salazar FM Engineer Mobily 3G Project
DTF MODE CALIBRATE: LOAD
If SHORT calibration is completed, Connect LOAD to RF port and then press continue.
Created by: Engr Russell Salazar FM Engineer Mobily 3G Project
DTF MODE DISTANCE Set the total distance i.e. from NodeB to Antenna port (length of Jumper Cables--indoor and outdoor, and Feeder Cable), then press Enter key.
Created by: Engr Russell Salazar FM Engineer Mobily 3G Project
DTF MODE AMPLITUDE Set the Max and Minimum Amplitude, press Amplitude (1) soft key Max (top) Min
Max value should be higher than the VSWR alarm value . For example, from LMT MML DSP VSWR, the value measured is 280(.01), Max value should be at least 4 or 5. Min value should at least be the ideal value, 1. Created by: Engr Russell Salazar FM Engineer Mobily 3G Project
DTF MODE MARKER Set the Marker (4) . Marker 1 (indoor jumper), Marker2 (Feeder), Marker3 (outdoor Jumper) Marker Select Marker Off on
Marker Edit
Mark the length of your cable, say indoor jumper cable=3m, feeder cable=35m,outdoor jumper cable=3m. M1=3, M2=38, M3=41. Created by: Engr Russell Salazar FM Engineer Mobily 3G Project
DTF MODE RUN/MEASURE Connect the RF cable to the RF Port. Press Hold (+/-) button to start the measurement
Created by: Engr Russell Salazar FM Engineer Mobily 3G Project
DTF MODE PEAK VALUE o Press Peak (6) button to see the maximum value of your measurement and see the corresponding distance from your marker.
Settings: START FREQ =1920 Mhz STOP FREQ = 2170 Mhz CAL ON DISTANCE = 40m M1=4m
M1
M1: 3.9m/2.0
Created by: Engr Russell Salazar FM Engineer Mobily 3G Project
DTF MODE LOAD SET-UP o If you have saved set-up configuration ( .sta), you can load it using the Load Button (7) . This will save time by not performing the calibration for the equipment. Only change the Cable type, Distance, Marker and or Amplitude if necessary.
Created by: Engr Russell Salazar FM Engineer Mobily 3G Project